Audiovox Pursuit PRO-OE2 Betriebsanleitung

Model : PRO-OE2

TRANSMITTER PROGRAMMING GUIDE

The transmitters included with the system have been pre-programmed

at the factory, with each button pre-assigned to control a specific function

of the system. Although the system in the vehicle has eithera2or3

channel receiver, depending on the model, the transmitters included with

the system are capable of transmitting 3 distinct signals. This allows you

to program each transmitter to more than one vehicle in two car families,

and also allows you to change which button(s) control certain functions

of the system.

( Example: Transmitter channel 3 can be programmed to activate

Receiver channel 2. ) Refer to the chart below for access to each of the

transmitter channels, and for the standard factory button assignments.

TRANSMITTER SYSTEM RECEIVER

CHANNEL BUTTONS CHANNEL FUNCTION

1 LOCK 1 Remote Lock & Unlock

UNLOCK & or **Remote Arm/Disarm

**Remote Emergency Panic

2 OPTION 2 * Pulsed Output for Accessories

3 LOCK 3 * Switched Output for Accessories

UNLOCK * Second Vehicle Control

& OPTION

Some of the more common accessories for these additional

channels are;

*AS 9154 Remote Garage Door Interface

*AS 9075 Remote car starter

*AS 9153 Remote window roll up

*AS 9256 Remote trunk release relay

** Only Available With Some Systems

PROGRAMMING THE TRANSMITTERS

It is important to remember that during programming, each individual step

of the procedure must be executed within 15 seconds of the previous step.

When the 15 second time limit is allowed to expire, the system will

automatically terminate the programming mode. This is indicated by a long

chirp from the siren.

Additionally, the system will store codes from up to four different

transmitters. Ifa5thtransmitter is programmed to any receiver channel,

then the first transmitter programmed to that channel will be erased from

the system's memory.

NOTE:Some Keyless Entry Units do not include a sounding device

therefore may not respond with beep tones where indicated below.

Simply follow the proceedure and where where indicated, press

and hold the transmitter button for 3 seconds.

To program new or additional transmitters,

1. Enter the vehicle, and turn the ignition key to the " on " position.

2. Flip the valet switch on - off - on - off - on - then off.

3. The dash L.E.D. will flash one time, and the sounding device will beep

one time, indicating the system is ready to accept programming for

receiver channel 1.

4. Press and hold the Lock/Unlock Icon button until the sounding device

emits a long beep, indicating the signal has been stored into memory.

5. If you have additional transmitters ( up to 4 ) that need to be programmed,

repeat step 4 for each transmitter.

6. Flip the valet switch on then off.

7. The dash L.E.D. will flash two times, and the sounding device will beep

two times, indicating the system is ready to accept programming for

receiver channel 2.

8. Press and hold the Option transmitter button until the sounding device

emits a long beep, indicating the signal has been stored into memory.

9. Ifyouhaveadditional transmitters ( upto 4 ) thatneed to be programmed,

repeat step 8 for each transmitter.

10. Flip the valet switch on then off.

11. The dash L.E.D. will flash three times, and the sounding device will

beep three times, indicating the system is ready to acceptprogramming

for receiver channel 3 (only available on certain models).

13. Ifyouhave additional transmitter( up to4 ) thatneed to be programmed,

repeat step 12 for each transmitter.

14. Turn the ignition key off. The sounding device will emit one short beep

followed by one long beep indicating the system has terminated the

program mode.

TRANSMITTER BATTERY REPLACEMENT

You will notice a decrease in transmitter range as the battery condition

deteriorates. Transmitter battery replacement is recommended at least

every 10 to 12 months, depending upon how frequently the transmitter is

used.

The transmitter has a small red L.E.D. built into the case. This L.E.D. can

be used to indicate battery condition. If the L.E.D. does not illuminate, then

the battery is discharged, and must be replaced.

To replace the transmitter battery,

1. Remove the small phillips head screw from the bottom cover of the

transmitter.

2. Carefully unsnap the top cover of the transmitter from the bottom cover.

3. Remove the discharged battery, making note of the location of the +

and - contacts, and replace with a new type GP 27A 12 volt battery.

4. Replace the transmitter cover, taking care not to damage the L.E.D.

or switches on the circuit board, and secure with the small phillips

head screw.

ORDER FORM FOR 2 BUTTON TRANSMITTER

MODEL NO. PRO OE2

Please indicate which transmitter pad is used with your transmitter as shown,

PD20 WhiteText PD21Red & White Text or PD22

IMPORTANT : To help us expedite your order, please print all of the information

legibly, and mail this form and your payment according to the instructions below.

1.Name: ____________________________________________________

Address: _____________________________________________________

City : _____________________ State : _______ Zip Code : ____________

2. Telephone Number : ( _______ ) _________________________________

3. Enter the total number of transmitters required here : ________________

4. The cost per transmitter is $ 65.00.

5. Enter the total amount enclosed here : ____________________________

( New York state residents must include the appropriate sales tax.)

6. Method of payment; check one of the boxes below.

Mastercard Visa Check or money order*(donotsend cash )

* Make checks payable to Audiovox Corporation

7. Credit Card Number : __________________________________________

8. Credit Card Expiration Date : _____________________

Credit card purchasers can order additional or replacement

transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and follow

the instructions from the operator interface.

9. Mail this form, and your check, to ;

Audiovox Corporation, 150 Marcus Blvd., Hauppauge, N.Y., 11788

Attn : TRANSMITTER DEPARTMENT



Inhaltsverzeichnis

Andere Audiovox Sender Handbücher

Audiovox

Audiovox S1BTXA Betriebsanleitung

Audiovox

Audiovox AX-2K4 Betriebsanleitung

Audiovox

Audiovox Pursuit OE3-FT3 Betriebsanleitung

Audiovox

Audiovox 128-5971 Montageanleitung

Audiovox

Audiovox Pursuit PRO-OE3 Betriebsanleitung

Audiovox

Audiovox AA923-AA94BT Betriebsanleitung

Audiovox

Audiovox ACA300 Bedienungsanleitung

Audiovox

Audiovox Auto Security SS91 Betriebsanleitung

Audiovox

Audiovox UltraGuard UG-OE3 Betriebsanleitung

Audiovox

Audiovox PSI 95BT3 Betriebsanleitung

Audiovox

Audiovox PRO92BTINT Betriebsanleitung

Audiovox

Audiovox APS 95 BT3S Betriebsanleitung

Audiovox

Audiovox PRO-94FR Betriebsanleitung

Audiovox

Audiovox Pursuit 095BPr Betriebsanleitung

Audiovox

Audiovox Prestige 103BP Betriebsanleitung

Audiovox

Audiovox AA-99BT2 Betriebsanleitung

Audiovox

Audiovox Pursuit 093BPr Betriebsanleitung

Audiovox

Audiovox ADDP1 Betriebsanleitung

Audiovox

Audiovox PRO94BT3 Betriebsanleitung

Audiovox

Audiovox AUTO SECURITY Prestige OE3B4 Betriebsanleitung

Audiovox

Audiovox PRO-OE3C Fehlerbehebungshandbuch

Audiovox

Audiovox A1BTX Betriebsanleitung

Audiovox

Audiovox Prestige APS-2K4 Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE3B4 Betriebsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung