Audiovox AX-2K4 Betriebsanleitung

128-6987

1 of 6

BUTTON RECEIVER

CHANNEL SYSTEM FUNCTION

Lock And Arm Alarm, also initiate and

terminates *Panic

Unlock And Disarm, also initiates and

terminates *Panic. Programmable to

unlock drivers door and or all doors.

Lock and arm/unlock and disarm. May

be programmed to unlock driver's door

or all doors. Also will initiate and

terminate *Panic.

Pulsed or switched output to control

Remote Trunk Release or optional

device connected to channel 3.

When pressed and release two times,

will provide pulsed output or activate the

Remote Start option when installed.

When so equipped, this button can be

used to operate an optional device

connected to channel 4.

When so equipped, this button can be

used to operate an optional device

connected to channel 5.

These transmitters makes use of icons (symbols) to identify the reac-

tion your security system/keyless entry/and or remote start system,

where applicable, will have when any icon (button) is pressed.

These icons are programmed at time of installation to meet the needs of

the individual and to complement the vehicle that the system is installed

in. To replace a transmitter or add transmitters, please follow the

programming instructions listed on the pages of this manual.

Transmitter Programming Guide

Model AX-2K4AX-2K4S,

AX-2K4MS,& AX-2K4MSFL

* Where So Equipped

128-6987

2 of 6

Some of the more popular options available for the unused Option

Buttons of your transmitter are:

AS 9554 Remote Garage Door Interface

AS 9075 Remote car starter

AS 9153 Remote window roll up

AS 9256 Remote trunk release relay

Although the most common use of the transmitter buttons are shown

on the front page of this guide, any button or button combination can be

programmed into any receiver channel. Additionally, if all 4 buttons are

used and you require access to a 5th channel, you would program a

combination of buttons to control the 5th function. i.e... You have

programmed lock for arm, unlock for disarm, trunk for trunk release,

and Opt1 for garage door operation, and you've added a window up

module that you want independent control of, you would program un-

lock and trunk buttons pressed simultaneously into the receiver to con-

trol this function independently. Also, if you do not program a transmit-

ter button into channel 2 which is the separate unlock/disarm chan-

nel, then whatever button is programmed into channel 1 will serve

as both lock/arm & unlock/disarm.

PROGRAMMING TRANSMITTERS:

NOTE: It is important to remember that during the programming mode,

each individual step must be completed within 15 seconds of

the previous step. If the 15 second time limit expires between

steps, the unit will automatically exit the program mode. This

is indicated by a long chirp from the siren.

Non alarm models will flash the parking lights only to confirm the

transmitter code has been learned and stored.

NOTE: Because the system may be capable of sounding a siren, the

vehicle horn, or both, where the siren chirp is referenced be-

low, the siren may chirp, the horn may beep, or both devices

may sound.

TO PROGRAM ADDITIONAL TRANSMITTERS:

1) Enter the vehicle, and turn the ignition switch to the on position.

2) Press and release the valet push button switch three times.

3) The dash mounted LED will flash 1x, and the siren will chirp 1x,

indicating that the system is ready to accept programming of channel

#1 which is arm/lock, disarm/unlock/unlock 2, and panic functions.

4) Press and hold the lock or lock/unlock symbol button of the transmit-

ter you wish to program for 4 seconds or until a long chirp is heard

from the siren.

"Repeat step 4 for each transmitter you wish to program".

NOTE: If your transmitter button has the Lock/Unlock icon on one

button, press and release the valet push button switch 2 times

then move on to step #8.

5) Press and release the valet push button switch one time to advance to

128-6987

3 of 6

channel2.Thesiren willchirp 2times andthe dashmounted LEDwill

Flash 2 times, indicating that the unit is ready to accept programming

for channel # 2 which is only used for separate lock and unlock

button transmitters, and is the disarm/unlock/unlock 2 and panic.

6) Press and hold the unlock symbol button of the transmitter you wish

to program for 4 seconds or until a long chirp is heard from the

siren.

"Repeat step 6 for each transmitter you wish to program".

7) Press and release the valet push button switch one time to ad-

vance to channel 3. The siren will chirp 3 times and the dash

mounted LED will Flash 3 times, indicating that the unit is ready

to accept programming for channel # 3 which is the trunk re-

lease/alternate output channel of the system.

8) Press and hold the trunk/key symbol button of the transmitter you

wish to program for 4 seconds or until a long chirp is heard from the

siren.

"Repeat step 8 for each transmitter you wish to program".

9) Press and release the valet push button switch one time to advance

to channel 4 if so equipped. The siren will chirp 4 times and the

dash mounted LED will Flash 4 times, indicating that the unit is ready

to accept programming for channel # 4, optional device (where

equipped)

10)Press and hold the Option button of the transmitter you wish to

program for 4 seconds or until a long chirp is heard from the siren.

"Repeat step 10 for each transmitter you wish to program".

11) Press and release the valet push button switch one time to ad-

vance to channel 5 if so equipped. The siren will chirp 5 times and

the dash mounted LED will Flash 5 times, indicating that the unit is

readyto acceptprogrammingfor channel#5 optional device(where

equipped)

12) Press and hold the second Option button of the transmitter you

wish to program for 4 seconds or until a long chirp is heard from the

siren.

"Repeat step 12 for each transmitter you wish to program".

ERASINGTRANSMITTERSIF THEYHAVEBEENLOST OR STOLEN:

NOTE: Before you begin to erase the lost or stolen transmitter(s),

have all transmitters available that you wish to remain pro-

grammed. These will be used during the program process

to identify transmitters that will continue to be used.

Enter the transmitter program mode:

1. Turn the ignition switch to the “ON” position.

2. Within 10 seconds, press and release the valet/program switch

three times. (Siren emits 1 short chirp indicating channel 1 has

been entered)

3. Within 10 Seconds, press and hold the ARM or ARM/DISARM

128-6987

4 of 6

button of the first transmitter you wish to remain stored into the

control unit until a single chirp is heard from the siren.

(Repeat this for each transmitter you wish to remain stored in the control

unit).

The receiver stores up to four transmitters. To be certain all transmitter

slots in the receiver are occupied with transmitters you wish to con-

tinue to use, and all others are erased, you will have to fill all four

receiver slots. If in step 3 you identified one transmitter, you will have

to fill the additional 3 slots. If in step 3 you identified two transmitters,

you will have to fill the additional two slots, etc...

4. Press and hold any unused button or combination of buttons until a

long chirp is heard from the siren. Release and press the button or

button combination again and again until all remaining slots are full.

NOTE: The button or combination of buttons entered will also control

the arm or arm/disarm function until additional transmitters are

added. All unwanted transmitters are now deleted.

REPRIORITIZING A TRANSMITTER’S PROGRAMMING:

To reprogram a receiver channel with a different transmitter button

once a code has been stored, there will be two options:

1. Enter the transmitter program mode of the receiver channel to be

reprogrammed. Using any unused button or combination of but-

tons, push out the stored code by pressing the unused button until

a long chirp is heard, then repeat 3 additional times. After this, you

can add any desired unused transmitter button. This action erases

only the button stored of the transmitter you are programming. All

other codes will remain stored.

2. Enter the transmitter program mode. Using any transmitter button

press and hold until a long chirp is heard. If a single chirp or multiple

chirps, (up to 7 chirps), are heard, the unit is indicating that the

transmitter has already been programmed elsewhere in the re-

ceiver. Release the transmitter button and within 5 seconds press

and hold until a long chirp is heard. This action forces the unit to

erase all stored codes of that transmitter.

The unit then exits the program mode the siren emits the program mode

exit chirp pattern. All transmitter buttons for that transmitter must now

be reprogrammed. Any other transmitter stored in the unit’s memory

still remain operational. If the button is released and not pressed again

within the 5 second period, no change in programming has been made

to the receiver channel. The programmer can move onto a different

channel or erase the transmitter codes as described in 1 above.

OPERATINGTHEFLASHLIGHTOFAX-2K4FL

If the transmitter packaged with your system included the

AX-2K4FL, (Flashlight Transmitter) By pressing the button located on

the side of the transmitter will cause the light on the end of the unit to

turn on.

128-6987

5 of 6

BATTERYREPLACEMENT:

Thetransmitter incorporatesa smallLED visiblethrough thecase which

is used to indicate battery condition. You will notice a decrease in

transmitter range as the battery condition deteriorates. Transmit-

ter batteryreplacement isrecommendedat leastevery10 to12 months,

depending upon how frequently the transmitter is used.

To replace the battery:

1) Remove the small # 0 phillips head screw from the rear of the case.

2) Remove the rear cover to access the discharged battery paying

attention to the proper polarity orientation.

3) Carefully remove and properly dispose of the discharged battery.

4) Insert the new battery, close the case, then reinstall the small case

screw removed in step 1.

5) If you accidently dislodge the cir-

cuitboard fromthe transmitterhous-

ing, be certain that the rubber mem-

brane is seated properly, and the

buttons are properly exposed from

the front view of the case, then

insert the circuit board, and return

to step #4.

QUICKREFERENCECHART:

You can program any individual channel without reprogramming all

channels. To go directly to a particular receiver channel follow the

chart below:

CHANNEL

1 Ign. On Then

2 Ign. On Then

3 Ign. On Then

4 Ign. On Then

5 Ign. On Then

6 Ign. On Then

VALET SWITCH

Press and Release 3 Times

Press and Release 4 Times

Press and Release 5 Times

Press and Release 6 Times

Press and Release 7 Times

Press and Release 8 Times

LED

1 Flash

2 Flashes

3 Flashes

4 Flashes

5 Flashes

6 Flashes

The light will turn off when the button is released.

Caution! Always point the light away from you and the eyes of

others. This is a bright high intensity LED which should not be directed

toward or into the eyes of anyone.

128-6987

6 of 6

1)PadNumber:_________________________________

2)Name:_______________________________________

3)Address:______________________________________

4) City: ________________ State: _____ Zip Code: ________

5)Telephone Number:(_____)_______________

6) Total Number Of Transmitters Required:

Cost Per Transmitter is: $65.00

Multiply By Number Of Transmitters X ______

7) Enter TotalAmount Enclosed _________________

(New York State Residents must include the appropriate sales tax)

8) Method of Payment:

Mastercard Visa Check or Money Order (do not send cash)

Make Checks Payable To Audiovox Corporation

CreditCardNumber:_________________________________

Credit Card Expiration Date: ____ / _____ / _____

9) Mail this form along with your payment to:

ORDERFORMFORAX-2K4AX-2K4S,AX-2K4MS, AX-2K4MSFL

Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y., 11788

Attn.:TRANSMITTERDEPARTMENT

Credit card purchasers can order additional or replacement

transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and

follow the instructions from the operator interface.

128-6987

Attention: Transmitter Ordering

Department

Important: Tohelpus expediteyour

order, please print all of the infor-

mation legibly and mail this form

and your payment according to the

instructions below.

Indicate the pad number of your

transmitter selected from the pads

shown above.

Note: Transmitter model number

found on back of case.

AX-2K4MSFL Main use PD 110, Side use 111

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Audiovox Sender Handbücher

Audiovox

Audiovox A1BTX Betriebsanleitung

Audiovox

Audiovox Prestige 105BP Betriebsanleitung

Audiovox

Audiovox PSI 95BT3 Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE3B3 Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE3 Betriebsanleitung

Audiovox

Audiovox Prestige 07S1BP Betriebsanleitung

Audiovox

Audiovox Prestige APS-2K4 Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE2B Betriebsanleitung

Audiovox

Audiovox PurSuit 08SPr Betriebsanleitung

Audiovox

Audiovox PurSuit 09XR1Pr Betriebsanleitung

Audiovox

Audiovox Pursuit 093BPr Betriebsanleitung

Audiovox

Audiovox Prestige APS-2K4MS Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE4 Betriebsanleitung

Audiovox

Audiovox AUTO SECURITY Prestige OE3B4 Betriebsanleitung

Audiovox

Audiovox AA-99BT2 Betriebsanleitung

Audiovox

Audiovox Pursuit 095BPr Betriebsanleitung

Audiovox

Audiovox Auto Security SS91 Betriebsanleitung

Audiovox

Audiovox Pursuit OE3-FT3 Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE2 Betriebsanleitung

Audiovox

Audiovox PRO92BTINT Betriebsanleitung

Audiovox

Audiovox PRO94BT3 Betriebsanleitung

Audiovox

Audiovox ACA300 Bedienungsanleitung

Audiovox

Audiovox AVX01BT3CL3 Betriebsanleitung

Audiovox

Audiovox ADDP1 Betriebsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung