Audiovox ACA300 Bedienungsanleitung

Wireless Transmitter and Receiver

Model:ACA300

Installation Manual

Features:

•Operating frequency: 2.4GHz.

•Converts Hard Wired Systems to Wireless

•Developed for Backup Camera Systems

•RCA Connector

Warnings

The product is intended to assist in safe driving and to allow the driver to

have a broader rearview while the vehicle is in reverse. You, as the driver,

are solely responsible for the safe operation of your vehicle and the safety

of your passengers according to the country and their local traffic

regulations. Do not use any features of this system to the extent it distracts

you from safe driving. Your first priority while driving should always be

the safe operation of your vehicle. Audiovox Electronics Corporation

cannot accept any responsibility whatsoever for accidents resulting from

failure to observe these precautions or safety instructions.

1. This product utilizes high voltage. Any unauthorized modifications

or damage to the products may result in electrical shock. Handle

all components with care. Inspect regularly for damage to

components and cabling.

anufacturer’s warranty.

warranties.

4. per

installation or modification of this product shall void all warranties.

2. You shall be responsible to ensure that the installation of this

product does not void or affect the vehicle manufacturer’s

warranty. Audiovox Electronics Corporation or its subsidiaries are

not liable in full or in part for improper installation resulting in

loss or damage to your property, or for voiding all or part of the

vehicle m

3. Do not apply excessive force to any of the components contained

within this kit. Excessive force used before, during or after installation

that results in a damaged or non-functional part shall void all

Please follow the procedure from this installation manual. Impro

Table of Contents

Warnings 1

Table of contents 2

Product description 2

Packing list 2

Transmitter/Receiver installation 3

Specifications 4

Troubleshooting 5

Product Description

The wireless transmitter and receiver have been developed to convert a

hard wire camera/monitor system to a wireless operation. The following

information contained in the installation manual is for camera backup

systems. Note: this product can be used on any Camera/Monitor system.

Packing List

1. Transmitter w/RCA Connector-1 qty

2. Receiver w/RCA Connector-1 qty

3. Wire connectors:

a. Tap connectors-3 qty

b. Ring connectors-1 qty

4. Installation Manual

5. Warranty Card

Transmitter/Receiver Installation

The transmitter and the receiver must be installed in the vehicle’s trunk or

interior. The transmitter and receiver are not weather proof and must be

located in a dry location

/Run Connection

a) Wiring the transmitter to the vehicle reverse lamp. Using the

tap connectors supplied.

i. Place the unstripped positive lead wire on the run channel

ii. Insert the unstripped red power wire completely

iii. Fold the tap connector back over the wires and make the

connection by crimping the u-contact down flush with the

plastic insulator.

iv. Close the top hinged cover until latched.

b) Black wire- Chassis/Ground. Using. Using the tap connectors

supplied.

i. Place the unstripped ground lead wire on the run channel

ii. Insert the unstripped black ground power wire completely

iii. Fold the tap connector back over the wires and make the

connection by crimping the u-contact down flush with the

plastic insulator.

iv. Close the top hinged cover until latched.

2. Wiring the transmitter to the camera.

a) Connect the transmitters RCA connector to the Cameras RCA

connector.

a. Wiring the receiver to the vehicle. Choose a source that only

has power when the vehicle is running. Connect as shown

Using the tap connectors supplied.

i. Place the unstripped ignition source wire on the run channel

ii. Place the unstripped red power wire completely

iii. Fold the tap connector back over the wires and make the

connection by crimping the u-contact down flush with the

plastic insulator.

iv. Close the top hinged cover until latched.

b. Black wire- Chassis/Ground. Using ground ring supplied,

i. Place stripped wire (1/4”) inside connector

ii. Crimp the connector using a crimping tool to secure the

wire.

Specifications:

1. Operating voltage: 11.5V-14.5V

2. Operating current:

Transmitter: 70mA

Receiver: 180mA

3. Operating frequency: 2.4GHz

4. Operating temperature: 0-50

Troubleshooting

Symptoms Solutions

The Monitor is not on after the

vehicle is started and vehicle is

in reverse?

Check the monitor and the receiver

wiring and connection.

No video signal appears while

reversing the vehicle?

Check the rearview Camera and the

Transmitter wiring connection.

Video image is not sharp

enough? Clean the lens of the camera.

Inhaltsverzeichnis

Andere Audiovox Sender Handbücher

Audiovox

Audiovox Prestige APS-2K4 Betriebsanleitung

Audiovox

Audiovox PRO94BT3 Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE3B4 Betriebsanleitung

Audiovox

Audiovox Pursuit 095BPr Betriebsanleitung

Audiovox

Audiovox AUTO SECURITY Prestige OE3B4 Betriebsanleitung

Audiovox

Audiovox Prestige 07S1BP Betriebsanleitung

Audiovox

Audiovox AA923-AA94BT Betriebsanleitung

Audiovox

Audiovox Prestige 103BP Betriebsanleitung

Audiovox

Audiovox Prestige APS-2K4MS Betriebsanleitung

Audiovox

Audiovox Prestige 105BP Betriebsanleitung

Audiovox

Audiovox Prestige APS-2K4 Betriebsanleitung

Audiovox

Audiovox PRO-94FR Betriebsanleitung

Audiovox

Audiovox Pursuit OE3-FT3 Betriebsanleitung

Audiovox

Audiovox Pursuit 095BPr Betriebsanleitung

Audiovox

Audiovox A1BTX Betriebsanleitung

Audiovox

Audiovox ADDP1 Betriebsanleitung

Audiovox

Audiovox PRO92BTINT Betriebsanleitung

Audiovox

Audiovox AA-99BT2 Betriebsanleitung

Audiovox

Audiovox PurSuit 091BPr Betriebsanleitung

Audiovox

Audiovox S1BTXA Betriebsanleitung

Audiovox

Audiovox PurSuit 08SPr Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE2B Betriebsanleitung

Audiovox

Audiovox PRO-OE3C Fehlerbehebungshandbuch

Audiovox

Audiovox Prestige APS-92BT-CL Fehlerbehebungshandbuch

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung