Auto Page RS-615 Bedienungsanleitung

RS-615

PROFESSIONAL REMOTE CAR STARTER

KEYLESS ENTRY SYSTEM

OPERATIONS MANUAL

THIS PRODUCT IS DESIGNED FOR PROFESIONAL INSTALLATION ONLY

SYSTEM OPERATIONS:

WARNINGS:

As with any product that performs automatic functions, there are certain safety

precautions that you must

practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is

corrected.

8. The use and operations of this system is the sole responsibility of the

operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle

running on public streets.

10.Do not start the vehicle by remote while the standard transmission vehicle is

parked at a steep place.

Transmitter

Button System Function Remark

Lock Doors

Panic function Press and Hold for 3 seconds

+ Silent Lock / Unlock Ignition in "off" position.

Unlock Doors

-Two Step Door Unlock (Driver’s

door on the first push; Passenger’s

door on the second push Press twice within 3 seconds.

Trunk Release (Channel 3) Press and Hold for 2 seconds

-Car Locator Under locked mode

Activate or Turn Off The Remote

Start

II Switching code For 2nd Car

Operation.For regular remote transmitter

Only

CHANGING THE BATTERY IN YOUR TRANSMITTERS

XT72S: This transmitter uses two (2) 3-volt lithium ion batteries

(#CR2016) that are sandwiched together with the (+) side facing upward.

To replace the battery, you will need to use a small flat blade screwdriver.

Locate the small notch on the lower right side of the transmitter case next

to the key ring. Using the flat blade screwdriver, carefully pry the top case

from the bottom case. It should snap apart after breaking the seal.

Before removing the batteries note the direction of the positive (+) terminal.

Place the new batteries in exactly the same manner, being careful not to

bend or damage the contact terminal. Snap the cases back together and

then test the transmitter to insure it arms and disarms the alarm.

ACTIVE LOCK:

1. Press button on the transmitter.

2. The horn will chirp once and parking lights will flash once indicating that

the system is now active. The vehicle doors will lock upon activating

when interfaced with the keyless entry system.

SILENT LOCKING / UNLOCKING: Pressing the + buttons

together on the transmitter will lock or unlock your system, No chirp sound

will be heard, lock / unlock confirmation will be through the

vehicle’s parking lights only.

ACTIVE UNLOCK:

1. Press button on the transmitter.

2. The horn will chirp twice and parking light will flash twice to indicating

that the keyless system is now unlocked. The vehicle doors will

unlock and dome lights will turn on for 30 seconds.

PATHWAY ILLUMINATION

(2) CR2016

3-Volt Batteries

This feature turns the parking light “ON” for 30 seconds upon a unlock

signal and for 10 seconds upon the lock signal.

TWO STEPS DOOR UNLOCK: This feature will independently unlock the

driver door only when deactivating the system. Pushing the

button a second time within 3 seconds will unlock the entire vehicle.

LED DISPLAY:

LED Function

Off Unlock

Slow

Flash Locked

On (Solid) Valet Mode

CHIRP INDICATOR:

Chirp Function

1 chirp Lock

2 chirps Unlock

6 chirps Car Locator

PARKING LIGHTS:

Parking light Function

1 flash Lock

2 flashes Unlock

12 flashes Car Locator

Constant On Under Remote Start

DEACTIVATING WITHOUT A TRANSMITTER

The Override function may be used if the remote transmitter is lost or

inoperative.

1. Enter the vehicle and turn the ignition switch to ‘ON’ position.

2. Within 10 seconds push and release the valet switch

If starter disable is installed. You can now start and operate the

vehicle normally.

VALET MODE:

The valet switch allows you to temporarily bypass all system function,

eliminating the need to hand your transmitter to parking attendants or

garage mechanics. When the system is in valet mode, and remote start

functions are bypassed, however the remote panic feature and remote

door locks will remain operational. To use the valet mode, the system

must first be deactivated either by using you remote transmitter, or by

operating the Manual override sequence.

Enter Valet Mode:

1. From the Unlock condition, turn the ignition to “ON” position.

2.Push and hold valet switch for 2 seconds until the LED turns on. The

LED will remain on as long as the system is in ‘valet mode’.

Exit Valet Mode:

1. Return to normal operation, turn ignition ‘on’.

2. Push and hold valet switch for 2 seconds, The LED will turn off

indicating the system has exited the valet mode.

PANIC FUNCTION: (IF CAR HORN IS INSTALLED)

The transmitter can be used as a remote panic switch to manually

trigger the vehicle’s horn in case of emergency.

1. Press and hold the button for 3 second. The horn will immediately

sound.

2. During panic mode, the normal function of this transmitter button will

be suspended. The and buttons can be used to lock and

unlock the doors (if the option is installed), however once the button is

pressed, the vehicle’s starter disable device, (where installed) will be

enabled allowing the vehicle to start.

3. To stop the panic, press and hold the or button on the

transmitter again for 3 seconds. Also if any transmitter button other

than the or button is pressed and released, the panic mode will

be turned off immediately.

4. If no buttons are pressed, the panic function will stop automatically in

30 seconds.

DOME LIGHT CONVENIENCE DELAY & SUPERVISION

This system is a unique feature, which will turn on your vehicle dome

light as following: (optional) Additional installation required.

1. Upon unlocking, the interior lights will remain on for 30 seconds.

Note: Turning on the ignition switch or activating the system will turn off

the dome light.

IGNITION CONTROL DOOR LOCKS.

If the vehicle’s door locks have been interfaced to the security system,

the system will automatically lock the vehicle’s doors when the ignition

is turned “ON” and /or unlock the vehicle’s doors when the ignition is

turned “OFF”.

TRUNK RELEASE

Press and hold the button on transmitter for two seconds to remote

control the trunk release or other electric devices.

CAR LOCATOR

Press the button twice with 3 seconds to active car locator function.

The horn will chirp 6 times. The parking light will flash 12 times, for you to

easily locate your car.

REMOTE START OPERATION:

WARNINGS:

As with any product that performs automatic functions, there are certain

safety precautions that you must practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or

garage.

5. Always apply the parking brake and lock the vehicle as you exit the

vehicle.

6. Should the unit malfunction, disconnect the fuse until the problem is

corrected.

7. The use and operations of this system is the sole responsibility of the

operator.

8. Some areas may have local ordinances that prohibit leaving a vehicle

running on public streets.

A. TO REMOTE START THE VEHICLE:

When you want to start your vehicle,

1. Press button once on the transmitter.

2. The parking lights will flash to indicate the remote start received the

signal.

3. The engine will start approximately 5 seconds.

4. Once the engine is running, after a couple of seconds the parking light

will turn on again and climate controls will activate and adjust the

vehicles interior temperature to your preset setting.

5. The vehicle will run for 5 to 30 minute cycle and automatically shut

down.

(SAFTEY START OPERATION:)

The safety start feature allows you to press the button once before the

vehicle will remote start or remote shut down.

NOTE: The Remote Start Unit will not start the vehicle if any one of the

following conditions exists:

1. The hood is opened.

2. The brake pedal is pressed.

3. Move the optional remote start enable toggle switch to OFF position.

(If installed)

4. The gear selector is in any gear other then “PARK” or “NEUTRAL”

TO TURN OFF THE REMOTE START:

When the engine is running (by remote start), if you want to stop it,

1. Press button once on the transmitter.

2. Move the optional remote start enable toggle switch to OFF position.

(If installed)

3. Press the brake pedal, the vehicle will shut down and turn off the parking

light to indicate engine stopped.

TO OVERRIDE VEHICLE FROM REMOTE START CONTROL:

To operate the vehicle while running from the remote start.

1. Insert the ignition key and turn it to “ON” (not the start) position.

2. Press the brake pedal.

Note: If the brake pedal is pressed before the key is in the ON

position, the engine will shut down.

TEMPORARY STOP FEATURE:

This feature allows the vehicle to remain running after the key has been

removed from the ignition. This feature is useful for occasions when you

wish to exit and lock the vehicle for short periods of time, but would like to

leave the engine running and the climate control on.

1. Before turning off the engine, press the button once on the

transmitter. The parking lights will come on and the LED will flash 3

times to confirm Temporary Stop feature ‘ON’

2. Turn the ignition key to OFF position. (The engine will stay running.)

3. The engine will run until the pre-programmed time elapsed or shutdown

input is received.

TIMER START:

This unit can be programmed to start and run the engine every 3 hours.

The engine will run for the programmed run time and then shut down.

IMPORTANT: Timer Start should be used only in open areas, Never start

and run the vehicle in on enclosed space as a garage or carport.

3 hours timer start: This feature is design for an extreme cold climate

usage. The system will auto start the vehicle every 3 hours, to prevent

engine freezing and hard to start.

A MAXIMUM OF SIX CYCLES CAN OCCUR.

ENTER:

1. Press the button once to remote start the vehicle. As soon as the

vehicle is running and the parking lights have turned ‘ON’.

2. Immediately press the button then press button. The parking light

will flash (3) times. The horn chirps (3) times. The vehicle is now

programmed to start every (3) hours.

3. Press the brake pedal to stop the vehicle running.

Exit the timer start:

Timer start can be exited manually as follows:

1. Repeat the Enter Steps from above.

1. Make sure the remote start system is not operating the engine.

2. Turn the ignition on. The LED and parking light will flash (4) times. The

horn chirps (4) times.

SHUTDOWN INPUT FOR REMOTE STARTER:

If any of the following conditions exist while the system is operating, the

engine will not start or will shut down immediately:

1. The hood is opened.

2. The brake pedal is pressed.

3. Move the optional remote start enable toggle switch to OFF position. (If

installed)

4. Engine is over-revved. {“Tachometer checking type” only}

5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.

6. Transmitter button is pressed.

7. The vehicle refused to start running after {3} unsuccessful attempts.

DISABLING THE REMOTE START SYSTEM: (If installed)

This feature allows your system’s remote start unit to be temporarily

disabled to prevent the vehicle from being remote started accidentally. This

feature is useful if the vehicle is being serviced or stored in an enclosed

area. To disable the remote start, move the optional remote start enable

toggle switch to the OFF position.

LIMITED LIFETIME WARRANTY PROVISIONS

( U.S. and Continental U.S. Only)

1. AutoPage, Inc. WARRANTS that this new unit has been thoroughly inspected and

tested at the factory prior to delivery. Your AutoPage equipment is guaranteed for

“life” to the original purchaser/user of the equipment under the following conditions:

If the product proves defective (according to AutoPage’s testing) within the first

year, the defective unit may be exchanged or repaired free of charge. “Proof of

Purchase” (dated sales receipt) must accompany all warranty returns; otherwise,

your return will be rejected and sent back. After one (1) year, the purchaser

should ship the unit prepaid to AutoPage with a money order in the amount of

$20.00 to cover shipping and handling charges. Note: The enclosed Warranty Card

may be required to receive warranty services.

2. This WARRANTY will be considered void if the equipment has been misused,

neglected, improperly serviced, altered, dropped or damaged by water, contrary to

the AutoPage OPERATIONS MANUAL. Or, if used with accessories not

approved by AutoPage, which may have contributed to the defect. See note below

regarding product installation.

3. The purchaser’s remedies under this WARRANTY shall be limited to the repair or

replacement of electronic components only. THE FOLLOWING IS NOT

COVERED: Damages or deterioration to cases, batteries, covers and cabinets; the

cost of repairs, replacement and labor of which shall be borne by the purchaser even

if occurring during the WARRANTY period.

4. Any equipment or parts which are claimed to be defective under this WARRANTY

must be sent to the AutoPage Service center with “proof of purchase” at the

purchaser’s expense prior to such return, a Return Authorization Number should be

obtained. AutoPage will return the equipment, charges prepaid. Warranty Service

can be provided through the dealer where the equipment is originally purchased.

5. Any unexpired WARRANTY shall be applicable to equipment and parts in the

possession of the original purchaser only.

6. THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE.

7. AutoPage shall not be liable, under the foregoing WARRANTIES or otherwise, for:

Any personal injury of any kind to the purchaser, its employees or agents or anyone

else whomsoever resulting directly or indirectly from the use or presence of the

equipment or parts; Consequential damages of any kind; any inability of the

purchaser to use the equipment.

IMPORTANT NOTE: Any damages to the alarm system resulting from an

installation performed by anyone other than a professional installation

technician authorized by a dealer of Auto Page will void the product’s

warranty.

This WARRANTY CARD is for your record. However, Auto Page reserves the

right to request you to submit this WARRANTY CARD, which must have

complete information to receive warranty service. Please keep this card in a

secured place.

AUTOPAGE WARRANTY SERVICE CARD

Model: _______________

Serial # _______________

CUSTOMER TO COMPLETE DEALER TO COMPLETE

Mr./Mrs./Ms.

___________________________ ________________________________

Your Name (Please Print) Company Name

___________________________ ________________________________

Address Dealer’s Address

___________________________ ________________________________

City, State, Zip Code City, State, Zip Code

___________________________ ________________________________

Telephone Number Dealer’s Telephone Number

___________________________ ________________________________

Year / Make / Model of Vehicle Date of Installation / Purchase

Andere Handbücher für RS-615

Inhaltsverzeichnis

Andere Auto Page Fernstartsystem Handbücher

Auto Page

Auto Page KE-120 Bedienungsanleitung

Auto Page

Auto Page C3-RS-1000 OLED Bedienungsanleitung

Auto Page

Auto Page RF-225 Bedienungsanleitung

Auto Page

Auto Page RS-610 Bedienungsanleitung

Auto Page

Auto Page RS-615 Bedienungsanleitung

Auto Page

Auto Page C3-RS-625 Bedienungsanleitung

Auto Page

Auto Page RS720LCD Bedienungsanleitung

Auto Page

Auto Page RS-8601cd Bedienungsanleitung

Auto Page

Auto Page C3-RS1100 OLED Bedienungsanleitung

Auto Page

Auto Page RS-725LCD Bedienungsanleitung

Auto Page

Auto Page C3-RS-665 Bedienungsanleitung

Auto Page

Auto Page RF-1055KE Bedienungsanleitung

Auto Page

Auto Page RS-620 Bedienungsanleitung

Auto Page

Auto Page RS-730 Bedienungsanleitung

Auto Page

Auto Page RS-750lcd Bedienungsanleitung

Auto Page

Auto Page RS-855lcd Bedienungsanleitung

Auto Page

Auto Page Car-Pro CPX-RS1 Bedienungsanleitung

Auto Page

Auto Page autopage RS-850lcd Bedienungsanleitung

Auto Page

Auto Page RS-662 Bedienungsanleitung

Auto Page

Auto Page RS-727LCD Bedienungsanleitung

Auto Page

Auto Page RS-660 Bedienungsanleitung

Auto Page

Auto Page TRX950 Bedienungsanleitung

Auto Page

Auto Page RST-1100 Bedienungsanleitung

Auto Page

Auto Page C3-RS-603 Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch