Automatic Technology Toro GDO-10v2 Bedienungsanleitung
GDO-10v2 ToroTM
Roll Up Garage Door Opener
INSTALLATION INSTRUCTIONS | OWNERS COPY
Featuring TrioCode™Technology
Technical Document
Installation Manual
v1.01
14 Dec 2011
English
Part # 13248(Manual)
2GDO-10V2 Toro™Owner Installation Instructions
WARNING: It is vital for the safety of persons to follow all
instructions.Failuretocomplywiththeinstallationinstructions
and the safety warnings may result in serious personal injury
and/or property and remote control opener damage. Please
save these instructions for future reference.
Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all
conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of
an Automatic Technology Australia Pty Ltd Garage Door Opener. Automatic Technology Australia Pty Ltd hereby further
expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person as a
result whether directly or indirectly from failure to install the Automatic Technology Australia Pty Ltd Garage Door Opener
in accordance with these installation instructions.
Owner Installation Instructions GDO-10V2 Toro™3
Important Safety Instructions 4
Features 6
Controllers Input And Output 8
Operating Controls 9
Package Contents 10
Pre-installation Requirements 11
Installation 12
EasyBeam™ Installation 14
Programming The Opener 15
Menu Structure 15
Viewing And Editing Parameters 16
Setting Limits 17
Setting Limits: Via Transmitter 18
Safety Obstruction Force 19
Safety Obstruction Force Test 19
Adjusting Safety Obstruction Forces 20
Coding Transmitters 21
Transmitter Editing 22
Transmitter Management 24
Remotely Coding Transmitters 26
Setting Pedestrian Position 27
Standard Operating Modes 27
Control Board Adjustments 29
Time Clock 34
Diagnostic Tools 36
Memory Tools 38
Accessories 38
Lock 38
Light 39
Auto-Close Mode 40
Wall Transmitter Installation 41
SmartSolar™ Installation 42
Replacing Backup Batteries 43
Specifications 44
Troubleshooting 45
Maintenance 46
Spare Parts 47
Warranty 48
GDO-10v2 Toro™
Roll Up Garage Door Opener
4GDO-10V2 Toro™Owner Installation Instructions
CAUTION: If your garage has no pedestrian entrance door, an emergency access device should be installed.
This accessory allows manual operation of the garage door from outside in case of power failure.
Photo Electric Beams must be installed with the automatic opener ensuring additional safety and peace
of mind.
DO NOT operate the opener unless the garage door is in full view and free from objects such as
cars and children/people. Make sure that the door has finished moving before entering or leaving
the garage.
DO NOT operate the opener when children/people are near the door. Children must be
supervised at all times when the opener is in use. Serious personal injury and/or property
damage can result from failure to follow this warning.
DO NOT allow children to operate the opener. Serious personal injury and/or
property damage can result from failure to follow this warning.
Regularly check to make sure that the Safety Obstruction Force is working
correctly, and is tested and set as per page 19 of this manual. Failure to follow
these instructions could result in serious personal injury and/or property
damage. This test must be repeated at regular intervals and the necessary
adjustments made as required.
The PE Beams must be used, if the closing force as measured on the
bottom of the door is over 400N (40kg).
DO NOT disengage the door opener to manual operation with
children/people or any other objects including motor vehicles
within the doorway.
The door opener is not intended for use by young children
or infirm persons without adequate supervision. Children
should be supervised to ensure that they do not play with
the remote transmitters or the opener.
Keep hands and loose clothing clear of the door and
door opener at all times.
The unit should be installed so that it is protected
from the elements. It should not be exposed to
water or rain. It is not to be immersed in water
or sprayed directly by a hose or other device.
WARNING: It is vital for the safety of people to follow all
instructions. Failure to comply with the following Safety
instructions may result in serious personal injury and/or
property damage.
Important Safety Instructions
Owner Installation Instructions GDO-10V2 Toro™5
The garage door must be well balanced. Sticking or binding doors must be repaired by a qualified garage door
installer prior to installation of the opener.
Frequently examine the installation for signs of wear, damage or imbalance. DO NOT use if repair or
adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury. DO
NOT attempt to repair the door yourself as hardware is under extreme tension.
Remove or disengage all garage door locks and mechanisms prior to installation of the opener.
Connect the opener to a properly earthed general purpose 240V mains power outlet installed by a
qualified electrical contractor.
Disconnect the power cord from mains power and backup batteries before making any repairs
or removing covers. Only experienced service personnel should remove covers from the
opener.
When using Auto-Close mode, a photo electric beam must be fitted correctly and tested
for operation at regular intervals. Extreme caution is recommended when using Auto-
Close mode. All safety rules must be followed.
In order for the opener to sense an object obstructing the door way, some force
must be exerted on the object. As a result the object, door and/or person may
suffer damage or injury.
If the power supply cord is damaged, it must be replaced by an Automatic
Technology service agent or garage door professional.
Make sure that the door is fully open before driving in or out of the
garage and fully closed before leaving the driveway.
Make sure that remote controls are kept out of reach of children.
Install the wireless wall control unit in a location where the
garage door is visible, at a height of at least 1.5m, out of the
reach of children and with the garage door is visible.
Important Safety Instructions
6GDO-10V2 Toro™Owner Installation Instructions
Operation
To open or close the door simply press the open or close button on the wall
control unit, a button on a coded TrioCode™ hand held transmitter, optional wall
mounted transmitter, or optional wall switch for two seconds. During open and
close cycles, the door can be stopped by pressing the button again or by pressing
the stop button on the wall control unit.
TrioCode™ Code Hopping Technology
Every time a TrioCode™ transmitter is used, a new security code is randomly
generated from over 4.29 billion possibilities. This greatly enhances the security of
the system and makes “code grabbing” a thing of the past.
These transmitters also overcome interference issues by simultaneously sending a
signal over three slightly different frequencies. Even if two of the three signals are
jammed, the system will still work.
M-ALPS (Magnetic Automatic Limits Positioning System)
M-ALPS does away with manual adjustment of the door’s limits position using mechanical
parts, such as cams and microswitches. During installation the hand held transmitter can be
programmed to set the door limit positions.
ISS (Intelligent Safety Obstruction System)
While the door is performing a close cycle, should it hit an obstacle or be restricted in some manner, it
will automatically reverse. The amount of force the door should encounter before reversing is automatically
adjusted by the doors control system during the initial installation of the automatic door opener. The door will
also stop if restricted whilst opening. The Safety Obstruction Force should be checked monthly.
Auto Courtesy Light
The courtesy light (if connected) comes on automatically for one minute whenever the door is activated. The
light can also be operated independently of the door by coding a dedicated button on a transmitter.
Features
Thank you for purchasing the Automatic Technology
Toro™ Automatic Garage Door Opener. Designed
by our renowned engineers to suit roll up doors, the
Toro™ will provide years of smart, simple & secure
convenience to your home.
Owner Installation Instructions GDO-10V2 Toro™7
SmartSolar™ Compatibility (Optional)
The opener can be fitted with a SmartSolar™ kit (Part Number 60142) for operation
where mains power access is not available. NOTE: If the door is the only entrance to
the garage, a keyed cable release should be fitted external to the garage.
Vacation Mode
A hand held transmitter can be programmed to lock and unlock all other
transmitters that have been programmed into the openers’ memory. The Vacation
Mode can be used when the door is left idle for long periods of time.
Pet/Pedestrian Mode
The transmitter can be programmed to open the door to an adjustable partial height
so that the family pet can enter and exit the garage at any time. You may also wish to
open the door to a height suitable only for pedestrian access.
Auto-Close Mode
The opener can be programmed to automatically close after an open cycle. The Auto-Close
time is adjustable. It is compulsory to install PE Beams if this mode is selected, otherwise the
door may cause personal injury or damage to property.
Photo Electric (PE) Beams
The opener has an input to connect PE Beams for extra safety and use of the Auto-Close mode.
Manual Operation
The opener is equipped with a unique patented manual disengaging device. If the power to the opener is
disrupted for any reason, the door can be put into manual mode by pulling down on the string handle, then
releasing. This will allow you to manually open or close the door. When power is restored, by pulling down on
the string handle and releasing, the opener is put back into automatic mode.
8GDO-10V2 Toro™Owner Installation Instructions
Controller Input And Outputs
Light Relay Output N/O, Com, N/C Contact
Lock Relay Output N/O, Com, N/C Contact
Serial Interface Connector
Programmer PG-3 Connector
12 volts 6 Amp - Hr Batteries
Engage/Disengagement Handle
Standby Battery Charger/Solar Connector
12
03
13
07
08
05
02
01
04
06
09
01
02
10
03
04
05
06
07
08
09
10
11
12
13
01
fig
11
Solar Shunt
Standby Battery Shunt
Motor Connector
10 Amps Slow Blow Fuse
24 Volts Ac In Connector
Position Sensor Connector
Owner Installation Instructions GDO-10V2 Toro™9
17
16
21
15
14 22
20
19 18
Terminal Block ( From Left To Right )
V+ Three Wire PE Beams “ + “ Supply
IN3 Three Wire PE Beams Trigger Input
V- Common For Two Wire EasyBeam™ and Three
Wire PE Beams
IN2 Two Wire EasyBeam™ Input
AUX OUT Receiver’s Auxiliary Output
FIRE N/O , N/C Input Terminal
GPI N/O Input Terminal
OPN N/O , N/C Input Terminal
STP N/O , N/C Input Terminal
CLS N/O Input Terminal
SWP N/O Input Terminal
COM Terminal For Inputs
Programmer PG-3 Input
Console Previous Button
Liquid Crystal Display
Console Next Button
Console Open Button
Console Stop Button
Console Set Button
Console Close Button
14 15
16
17
18
19
20
21
22
02
fig
Operating Controls
10 GDO-10V2 Toro™Owner Installation Instructions
Package Contents
GDO-10v2 Toro™ Drive Unit 1
Wall Control Unit 1
Network Cable 1
Accessory Guide Pack 1
Fork Extension Pack 3
TrioCode™ Keyring Transmitters 2
Installation Manual 1
Locking Bar Covers 2
EasyBeam™ with wires and brackets 1
03
fig
Inhaltsverzeichnis
Andere Automatic Technology Garagentoröffner Handbücher
Automatic Technology
Automatic Technology Toro GDO-10V2L2 Bedienungsanleitung
Automatic Technology
Automatic Technology iOpener RD40 Bedienungsanleitung
Automatic Technology
Automatic Technology Axess Pro Series 1101 Kurzanleitung
Automatic Technology
Automatic Technology GDO-11V3 Ero Bedienungsanleitung
Automatic Technology
Automatic Technology Axess Pro Series 1101 Bedienungsanleitung
Automatic Technology
Automatic Technology SecuraLift Trio Bedienungsanleitung
Automatic Technology
Automatic Technology GDO-8 ShedMaster Benutzerhandbuch
Automatic Technology
Automatic Technology GDO-10V3L2 Toro Bedienungsanleitung
Automatic Technology
Automatic Technology GDO-11v1 Ero Kurzanleitung
Automatic Technology
Automatic Technology Hiro GDO-12V1 Bedienungsanleitung
Automatic Technology
Automatic Technology NeoSlider TrioCode 128 NES-500 Bedienungsanleitung
Automatic Technology
Automatic Technology GDO-6v3 EasyRoller Bedienungsanleitung
Automatic Technology
Automatic Technology Syncro ATS-3 Bedienungsanleitung
Automatic Technology
Automatic Technology GDO-6v3 EasyRoller Bedienungsanleitung
Automatic Technology
Automatic Technology GDO-9 Dynamo Gen 2 Bedienungsanleitung
Automatic Technology
Automatic Technology GDO-9v2 SecuraLift Bedienungsanleitung
Automatic Technology
Automatic Technology GDO-9v2 Enduro Gen 2 Bedienungsanleitung
Automatic Technology
Automatic Technology GDO-11v1 SecuraLift Bedienungsanleitung
Automatic Technology
Automatic Technology GDO-7v2 SecuraLift Bedienungsanleitung
Automatic Technology
Automatic Technology GDO-9 Dynamo Gen 2 Bedienungsanleitung
