10 11 12
FIG. 4 – GENIUS PLUS PCB LAYOUT
JUMPER SWITCHS SETTING
Pulse Jumper - Provides control for normal or high
risk operating environments.
LED Jumper – LED control selection
WIRE SIZE REQUIREMENTS
Use #22 AWG (0.5 mm) or wires with a larger
diameter. Use the following table to determine
required wire gauge (diameter) and length of wire
between the detector and the control panel.
Wire Length m 200 300 400 800
Wire Diameter mm .5 .75 1.0 1.5
Wire Length ft. 800 1200 2000 3400
Wire Gauge # 22 20 18 16
13 14 15
FIG. 5 – WIDE ANGLE LENS PATTERN
0m 5m 10m 15m
0ft 16.4ft 32.8ft 49.2ft
2.4m
7.9ft
0m
0ft 15m
49.2ft
WIDE ANGLE LENS PATTERN
COVERAGE WIDE
ANGLE
90°
15m x 22m
49.2ft x 72.2ft
___________________________________
TOTAL
DETECTION 42
ZONES
IMPORTANT:
In an environment with a small animal:
1. The GENIUS PLUS has to be mounted at
2.4m (7ft.) or higher (max 2.7m or 7.9ft.)
above floor level.
2. Install the GENIUS PLUS vertically (not
tilted forward).
3. Away from furniture 2.4m (7.9ft.) or
objects, on which a small animal may
jump.
4. Not facing a staircase, ladder or similar
object that can be part of the monitored
environment (the vertical motion of the
animal may be interpreted by the detector
as an actual intruder).
5. Flip jumper switch “PULSE to the “AUTO”
(down) position for a harsh environment.
TEST PROCEDURES
Wait one minute warm-up time after applying 12
VDC power. Conduct testing with the protected area
cleared of all people.
Walk test
• Remove front cover.
The pulse jumper must be in position 1.
The LED must be enabled.
• Replace the front cover.
• Start walking slowly across the detection
zone.
• Observe that the detector’s LED lights
whenever motion is detected.
• Allow 5 sec. between each test for the
detector to stabilize.
• After the walk test is completed, the LED
may be disabled.
NOTE:
Walk tests should be conducted, at least once a
week, to confirm proper operation and coverage of
the detector.
16 17 18
TECHNICAL SPECIFICATIONS
Power input 8.2 - 16VDC
Current consumption
Standby 13mA at 12VDC
Active 8.5mA at 12VDC
Detection speed 0.15 to 1.8m/sec (0.5 to 6 ft./sec)
Alarm output N.C 50mA at 24VDC
27ohm in line resistor
Tamper switch N.C 50mA at 24VDC
10ohm in line resistor
Operating temperature -20°C to 50°C (-4°F to 122°F)
Operating humidity Up to 95% (non-condensing)
Storage temperature -40°C to 80°C (-40°F to 176°F)
Detection method 2 matching dual element
with double optic system
RFI protection >30V/m at 10 to 1000MHz
EMI immunity50,000Volt electrical interference
due to power surges or lighting
LED Indicator LED is blinking 8 times during
warm up period and self-testing 12 Sec.
LED is ON during alarm.
Dimensions 88 x 48 x 33mm
(3.46” x 1.9” x 1.3”)
Weight 53 gr. (1.9 oz)
WARRANTY
Av-Gad Systems Ltd. and its subsidiaries and affiliates
(“Seller”) warrant its products to be free from defects in
materials and workmanship under normal use for 12
months from the date of sale. Because Seller does not
install or connect the product and because the product may
be used in conjunction with products not manufactured by
Seller, Seller cannot guarantee the performance of the
security system which uses this product. Seller’s
obligation and liability under this warranty is expressly
limited to repairing or replacing, at Seller’s option, within
a reasonable time after the date of delivery, any product
not meeting the specifications.
Seller makes no other warranty, expressed or implied,
and makes no warranty of merchantability or of fitness
for any particular purpose.
In no case shall seller be liable for any consequential or
incidental damages for breach of this or any other
warranty, expressed or implied, or upon any other basis
of liability whatsoever.
Seller’s obligation under this warranty shall not include
any transportation charges or costs of installation or any
liability for direct, indirect or consequential damages or
delay.
Seller does not represent that its products may not be
compromised or circumvented; that the product will
prevent any personal injury or property loss by burglary,
robbery, fire or otherwise; or that the product will in all
cases provide adequate warning or protection.
Buyer understands that a properly installed and maintained
alarm may only reduce the risk of burglary, robbery or fire
without warning, but it is not insurance or a guarantee that
such will not occur or that there will be no personal injury
or property loss as a result.
CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR
ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER
LOSS BASED ON A CLAIM THAT THE PRODUCT FAILS TO
GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE,
WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR
DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR
OTHERWISE, REGARDLESS OF CAUSE OF ORIGIN, SELLER’S
MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED
THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE
THE COMPLETE AND EXCLUSIVE REMEDY AGAINST
SELLER.
No employee or representative of Seller is authorized to
change this warranty in any way or grant any other
warranty.
Warning: Test this product at least once a week
Item 4775
UK. Edition 2, March 2005
These instructions supersede all previous issues in circulation prior
to April 2003.
Genius manual English
This setting is for a stable
environment without air drafts.
The GENIUS PLUS will automatically select
the appropriate pulse count level according to
the strength of the incoming signals.
This setting is for operation in a harsh
environment with air drafts or with a small
animal less than 25cm (0.8ft) in height and less
than 5kg (11.02lbs).
In AUTO mode, the GENIUS PLUS will increase
its sampling rate and take more factors into
account.
LED ENABLE - The LED will light when
the GENIUS PLUS is in alarm condition.
LED DISABLE - The LED is disabled.
PYRO-
SENSORS
Wire Terminal
TAMPER
LED
JUMPER
PULSE
JAMPER
LED
The Genius Plus provides PET immunity
up to 5Kg (11.02 lbs).
