Avital Point 3 Immobilizer Bedienungsanleitung

Point3

Immobilizer Installation Manual

Control Unit

1.Select a location under the dash that will allow you to use the tie wraps to

securely fasten the control unit.

2.Mount the control unit as high as possible to ensure maximum security.

3.Do not mount the control unit near moving parts.

4.Avoid areas that are in the direct path of air blowing from the vents.

5.Route wires from this point, leaving slack for ease of service.

NOTE: All wires are BLACK. Each wire has a WHITE label to identify

their purpose (see Wiring Diagram). Remove the white label after you

make your wire connections.

Wiring Diagram

Ignition Disable

ICAUTION: Make sure the wires are solidly connected. The ignition

circuit may draw very high current. We recommend that all

connections be soldered.

1.Locate the ignition switch loom under the dashboard.

2.Use a voltmeter to locate the one wire that shows +12 volts when the

ignition key is in the "ON," "CRANK" and "RUN" positions, and 0 volts

when the ignition key is in the "OFF" position.

3.Cut this wire in half. Test by attempting to start the engine with the ignition

key. The starter will crank but the engine will not start.

4.Connect one of the control unit ignitionand ignition input wires to the

vehicle ignition switch side.

5.Connect the other control unit ignitionwire to the vehicle ignition coil

side.

Starter Disable

ICAUTION: Make sure the wires are solidly connected. The starter

circuit may draw very high current. We recommend that all

connections be soldered.

1.Locate the ignition switch wire loom under the dashboard.

2.Use a voltmeter to find the one wire that will show +12 volts while the

ignition key is in the "CRANK" position only. This should be the starter

solenoid wire.

3.Cut the starter solenoid wire. Test by trying to crank the starter with the

ignition key. If it does not crank, you have the correct wire.

4.Connect one of the control unit starterwires to the vehicle starter switch

side.

5. Connect the other control starterwire to the vehicle starter solenoid side.

Additional Disable Circuit

The wires labeled 30 amp relay are used to immobilize a third circuit on the

vehicle. This wire can be used to interrupt a secondary ignition wire or fuel

pump relay.

ICAUTION: Make sure the wires are solidly connected. The disable

circuit may draw very high current. We recommend that all

connections be soldered.

1.Use a voltmeter to locate the wire you have chosen to immobilize.

2.Cut this wire in half.

3.Connect one of the control unit 30 amp relaywires to one side of the

vehicle wire.

4.Connect the other control unit 30 amp relay wire to the other end of the

vehicle wire.

Optional Horn Output

1.Use a voltmeter to locate the vehicle (-) horn output wire, at the steering

column.

2.Connect the control unit horn wire to the vehicle horn wire.

Coded Key Receptacle

1.Choose a location under the dashboard or in the center console that is

easy and convenient for the customer.

2.Use the two supplied screws to mount the receptacle.

3.Plug the receptacle into the control unit.

Valet Switch

1.Discuss placement with the owner.

2. Choose a location for the valet switch that is hidden, but convenient for

the owner to access.

3.Drill a ¼" hole and mount the switch.

4. Route the valet switch wires to the control unit.

5.Plug the valet switch BLUE connector into the control unit BLUE plug.

Power and Ground Connections

1.Connect the Immobilizer power wire (labeled "constant +12 volt") to one

end of the fuse assembly. Connect the other end of the fuse assembly to

the ignition switch harness constant +12 volt wire.

NOTE: This wire must be at least 14 ga.

2.Connect the Immobilizer ground wire (labeled "system ground ") to a solid

chassis ground.

NOTE: An under-dash, factory ground bolt would be ideal.

3.Insert 5 amp fuse into fuse holder.

Adding/Deleting Coded Keys

1.Turn the ignition key to the “ON” position.

2.Flick the valet switch to the “ON” position.

3. Turn the ignition key to the “OFF” position.

4.Within 15 seconds, turn the ignition key ON, then OFF 5 times. The LED

will flash rapidly to indicate the system is now in the programming mode.

5. Within 10 seconds, insert and remove the new coded key into the

under-dash receptacle.

6.Within 10 seconds, insert and remove any additional key you wish to

operate the Immobilizer. (You can add up to 4 coded keys to your

Immobilizer.)

7.To exit programming, turn the ignition key to the “ON” position or wait 10

seconds and the Immobilizer will automatically exit programming.

8.In the event of a lost or stolen coded key, repeat steps 5 & 6 four times.

This will automatically erase the missing coded key from memory.

Inhaltsverzeichnis

Andere Avital Autoalarmanlage Handbücher

Avital

Avital Hurricane Bedienungsanleitung

Avital

Avital AVISTART 6501 Bedienungsanleitung

Avital

Avital 4300 Bedienungsanleitung

Avital

Avital MAXX3 Bedienungsanleitung

Avital

Avital Maxx 1 Bedienungsanleitung

Avital

Avital AviStart 3200 Bedienungsanleitung

Avital

Avital 4103 Bedienungsanleitung

Avital

Avital 4003 Bedienungsanleitung

Avital

Avital Hurricane 3 Bedienungsanleitung

Avital

Avital Paging Adaptor 5810 Bedienungsanleitung

Avital

Avital Diablo Bedienungsanleitung

Avital

Avital Remote Access Bedienungsanleitung

Avital

Avital AMX7 Bedienungsanleitung

Avital

Avital Phoenix Bedienungsanleitung

Avital

Avital Diablo 2 Bedienungsanleitung

Avital

Avital Phoenix 2 Bedienungsanleitung

Avital

Avital AviStart 6000 Bedienungsanleitung

Avital

Avital AviStart 3100 Bedienungsanleitung

Avital

Avital 3100L Bedienungsanleitung

Avital

Avital 4308L Bedienungsanleitung

Avital

Avital AVISTART 4000 Bedienungsanleitung

Avital

Avital 3300L Bedienungsanleitung

Avital

Avital 2300 Bedienungsanleitung

Avital

Avital 2200 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung