AWS AMW-50 Bedienungsanleitung
American Weigh Scales, Inc.
AMW
-
50
AMW
-
150
AMW
-
250
AMW
-
500
User Manual
AMW Series
Digital Pocket Scale
AMW Series Manual
Thank you for purchasing the American Weigh
AMW-Series digital scale. Please read all operating
instructions carefully before use. This electronic scale
is a precision instrument. With normal care and proper
treatment, it will provide years of reliable service.
Never load the scale with more than the maximum
capacity. Overloading will permanently damage it!
Avoid any exposure to extreme heat or cold. Your
scale works better when operated at normal room
temperature. Always allow the scale to acclimatize to
normal room temperature for at least one hour before
use.
Give your scale suf cient warm up time. Usually
30-60 seconds before calibration to give the internal
components a chance to stabilize.
Keep your scale in a clean environment. Dust, dirt,
moisture, vibration, air currents and a close distance to
other electronic equipment can all cause an adverse
effect on the reliability and accuracy of your scale.
Handle with care. Gently apply all items to be weighed
onto tray top. Although this scale is designed to be
quite durable, try to avoid rough treatment as this may
permanently damage the internal sensor.
Avoid shaking, dropping or otherwise shocking the
scale. This is a precision instrument and must be
handled with extreme care.
Only operate the scale on a stable, vibration free
surface.
I. OPERATION
Place Scale on a horizontal at surface.
1. Press [ON/OFF] key.
2. Wait until "0.0” is displayed.
3. Put the object(s) on the weighing platform.
4. Using the [MODE] key, you can switch between the
weighing units.
II. TARE WEIGHING
1. Turn on scale as described above.
2. Place the "tare item" on the platform.
3. Press [TARE] and wait until "0.0" is displayed.
4. Add the "net-weight-item".
III. CALIBRATION
Calibration is NOT required before rst use. Only
calibrate if scale is not weighing properly.
**Make sure you use the correct calibration weight for
your scale or the calibration will not be accurate**
AMW-50: 50g calibration weight
AMW-150: 100g calibration weight
AMW-250: 200g calibration weight
AMW-500: 500g calibration weight
Calibration Procedures for AMW-150, 250, 500
(AMW-50 Calibration Procedures on next page)
1, Turn OFF the scale, press and hold the [CAL] key
and then press [ON/OFF] shortly. After 1-2 seconds,
the scale will display a random number. Now release
the [CAL] key.
2, Wait 2 seconds and press [ON/OFF] key again
shortly.
3, The LCD display will read “2ero” followed by the
amount of weight required to calibrate (listed above).
4. Place the required calibration weight on the platform
(ie. AMW-150 place a 100g on the scale)
5. Press [ON/OFF] again. The LCD display reads
“CAL”, then “PASS”.
6. Remove the weight and press [ON/OFF] to turn off
the scale. Finished!
Repeat if needed.
Calibration Procedures for AMW-50
1. Turn OFF the scale.
2. Press [ON/OFF] shortly. Then immediately press
and hold [MODE] until “CAL” is displayed. Release the
[MODE] key.
3. Press [MODE] again. Now the display will show
“CAL” and “50.00” will ash 3 times.
4. Place a 50g weight on the center of platform. Wait
3-4 seconds. The LCD display will read “PASS”, then
“50.00”.
5. Remove the weight and press [ON/OFF] to turn off
the scale. Finished! Repeat if needed.
Please check the availability of weights at the store
you bought your scale from.
IV. TROUBLESHOOTING
The primary reasons for inaccuracy or malfunction
are low batteries, incorrect calibration, overload or
operating on an unstable surface. Please keep this in
mind and maintain and operate your scale properly.
This scale is a precise instrument and must be
handled with the utmost care and caution.
[Display]
Elimination of errors
Nothing, Battery-Symbol, [lo] or [88888]
Change the batteries.
[OUE2]
Recalibrate the scale as shown above.
[EEEEE]
You are overloading the scale. Remove the
excessive load immediately!
[LLLLL]
The delicate weighing load cells have
been damaged by misusing the scale
(i.e. it was shocked, dropped or
overloaded). You can try recalibrating the
scale. If the load cell has not been
damaged too much it will work
again after recalibration.
[UNST]
Use the scale in a more stable position
Model
AMW-150
AMW-250
AMW-500
AMW-50
Capacity
150g
5.3oz
4.8ozt
96.5dwt
250g
8.82oz
8.54ozt
160.8dwt
500g
17.64oz
16.08 ozt
321.5dwt
50g
1.764oz
250ct
771.5gn
Resolution
0.1g / 0.005oz / 0.005ozt / 0.1dwt
0.01g
0.001oz
0.05ct
0.2gn
Backlight
• • • •
Calibration Weight
(not Included)
100g
200g
500g
50g
Platform Dimensions
(inches)
2.5 x 3 (
Stainless Steel on AMW500 ONLY
)
Stainless Steel on AMW500 ONLY)Stainless Steel on AMW500 ONLY
Scale Dimensions
(inches)
5 x 3 x 0.75
Power
2 x AAA Batteries (included)
Gross Weight
0.36 lb
0.43 lb
0.36 lb
Speci cations
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere AWS Skala Handbücher
AWS
AWS SG-300 Bedienungsanleitung
AWS
AWS 330CVS Bedienungsanleitung
AWS
AWS LB-1000 Bedienungsanleitung
AWS
AWS TS-200 Bedienungsanleitung
AWS
AWS 396LUMA Bedienungsanleitung
AWS
AWS AT-500 Bedienungsanleitung
AWS
AWS 2K-BOWL Bedienungsanleitung
AWS
AWS AMS-150 Bedienungsanleitung
AWS
AWS Gemini-20 Bedienungsanleitung
AWS
AWS Blade-100 Bedienungsanleitung
AWS
AWS SM-200 Bedienungsanleitung
AWS
AWS CP2-100 Bedienungsanleitung
AWS
AWS AERO-100 Bedienungsanleitung
AWS
AWS SR-1KG Bedienungsanleitung
AWS
AWS SR-1KG Bedienungsanleitung
AWS
AWS MC series Bedienungsanleitung
AWS
AWS V2-600 Bedienungsanleitung
AWS
AWS CUBE-100 Bedienungsanleitung
AWS
AWS QS-500 Bedienungsanleitung
AWS
AWS ACP-200 Bedienungsanleitung
