AWS Blade-50 Bedienungsanleitung
American Weigh Scales, Inc.
BLADE-50
BLADE-100
BLADE-600
BLADE-1000
User Manual
BLADE Series
Digital Pocket Scale
Blade Manual
Thank you for purchasing the American Weigh Blade
Series digital pocket scale. Please read all operating
instructions carefully before use. Scales are precision
instruments and should always be handled with proper
care. To ensure years of reliable service, keep these
simple tips in mind:
• Do not exceed the scales maximum capacity.
Overloading your scale can permanently damage it!
• Avoid exposure to extreme heat or cold. Scales
perform best at normal room temperature. If
temperatures have changed dramatically, recalibration
may be necessary.
• Allow your scale to warm up for 30-60 seconds
before performing calibration (if available).
• Store your scale in a clean, dry location. Dust, dirt,
and moisture can accumulate on the weighing sensors
and electronics causing innacuracy or malfunction.
• Avoid using your scale in close proximity to strong
radio wave emitting devices such as computers, cash
registers, and cordless phones.
• Always weigh on a at and level surface, free from
vibrations and drafts. The corner of a room is usually
the most stable.
• Gently apply all items to be weighed. Do not drop
items onto the weighing platform.
• Avoid dropping your scale. The warranty does not
cover damage due to rough treatment or overload.
I. OPERATION
Place Scale on a horizontal at surface.
1. Press [ON/OFF] key.
2. Wait until "0.0” is displayed.
3. Put the object(s) on the weighing platform.
4. Using the [MODE] key, you can switch between the
weighing units.
II. TARE WEIGHING
1. Turn on scale as described above.
2. Place the "tare item" on the platform.
3. Press [TARE] and wait until "0.0" is displayed.
4. Add the "net-weight-item".
III. CALIBRATION
Calibration is NOT required before rst use. Only
calibrate if scale is not weighing properly.
**Make sure you use the correct calibration weight for
your scale or the calibration will not be accurate**
BLADE-50: 50g calibration weight
BLADE-100: 100g calibration weight
BLADE-600: 500g calibration weight
BLADE-1000: 1000g calibration weight
1. Turn ON the scale.
2. Press and hold the [MODE] key until “CAL” is dis-
played. Release the [MODE] key.
3. Press [MODE] again. Now the display will read
“CAL” and the required calibration weight will ash 3
times.
4. Place the required calibration weight for your scale
on the center of platform. Wait 3-4 seconds. The LCD
will display “PASS”.
5. Remove the weight and press [ON/OFF] to turn off
the scale. Finished! Repeat if necessary.
IV. BLADE1000 Calibration Procedures
You will need a 1000g (1kg) calibration weight.
1. Turn on the scale by pressing [ON/OFF] key.
2. Wait until the LCD displays “0.0” then press and
HOLD the [MODE] key for 3 seconds. The LCD will
display “CAL”. You can now release the [MODE] key.
3. Press [MODE] key again, the LCD will display “CAL”
and “1000.0”.
4. Add 1000g calibration weight, the display will show
“PASS” and return to normal weighing mode.
5. Put away the calibration weight and press [ON/OFF]
to turn off the scale. Finished! Repeat if necessary.
V. TROUBLESHOOTING
The primary reasons for inaccuracy or malfunction
are low batteries, incorrect calibration, overload or
operating on an unstable surface. Please keep this in
mind and maintain and operate your scale properly.
This scale is a precise instrument and must be
handled with the utmost care and caution.
[Display] Elimination of errors
Nothing, Battery-Symbol, [lo] or [88888]
Change the batteries.
[OUE2] Recalibrate the scale as shown above.
[EEEEE] You are overloading the scale. Remove the
excessive load immediately!
[LLLLL] The delicate weighing load cells have
been damaged by misusing the scale
(i.e. it was shocked, dropped or
overloaded). You can try recalibrating the
scale. If the load cell has not been
damaged too much it will work
again after recalibration.
[UNST] Use the scale in a more stable position
Model Blade-600 Blade-1000 Blade-50 Blade-100
Capacity 600g
21.16oz
19.29ozt
385.8dwt
1000g
35.27oz
32.15ozt
643.0dwt
50g
1.764oz
250ct
771.5gn
100g
3.528oz
500ct
1543gn
Resolution 0.1g
0.01oz
0.01ozt
0.1dwt
0.01g
0.001oz
0.05ct
0.1gn (0.2gn minimum)
Weighing Units g, oz, ozt, dwt g, oz, ct, gn
Calibration Weight (not Included) 500g 1000g 50g 100g
Platform Dimensions (inches) 2.75 x 2.75 (Stainless Steel )
Scale Dimensions (inches) 3.75 x 3.75 x 0.75
Power 2 x AAA Batteries (included)
Specications
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere AWS Skala Handbücher
AWS
AWS 330LPW Montageanleitung
AWS
AWS SG-300 Bedienungsanleitung
AWS
AWS PW-44 Bedienungsanleitung
AWS
AWS SHIP-330 Bedienungsanleitung
AWS
AWS AMW-DISC-55 Bedienungsanleitung
AWS
AWS LB-SERIES Bedienungsanleitung
AWS
AWS BT2-201 Bedienungsanleitung
AWS
AWS MB-50 Bedienungsanleitung
AWS
AWS VP-100 Bedienungsanleitung
AWS
AWS QS-500 Bedienungsanleitung
AWS
AWS BLADE-50 Bedienungsanleitung
AWS
AWS SC-501 Bedienungsanleitung
AWS
AWS EXTEND-5K Bedienungsanleitung
AWS
AWS EDGE-5K Bedienungsanleitung
AWS
AWS AMW-810 Bedienungsanleitung
AWS
AWS MSC-100 Bedienungsanleitung
AWS
AWS CP-300 Bedienungsanleitung
AWS
AWS 330HRS Bedienungsanleitung
AWS
AWS ECOWEIGH Series Bedienungsanleitung
AWS
AWS CP3-100 Bedienungsanleitung
