AWS CP3 Series Bedienungsanleitung

American Weigh Scales, Inc.

CP3-100 (100x0.01g)

CP3-650 (65 0x0.1g) User Manual

CP3-Series

Digital Pocket Scale

Zero

ZERO

PCS

UNITS

OFF

T A R E

LIGHT

CP3-Series Manual

Thank you for purchasing the American Weigh CP3-

Series digital pocket scale. Please read all operating

instructions carefully before use. Scales are precision

instruments and should always be handled with proper

care. To ensure years of reliable service, keep these

simple tips in mind:

• Do not exceed the scales maximum capacity.

Overloading your scale can permanently damage it!

• Avoid exposure to extreme heat or cold. Scales

perform best at normal room temperature. If

temperatures have changed dramatically, recalibration

may be necessary.

• Allow your scale to warm up for 30-60 seconds

before performing calibration (if available).

• Store your scale in a clean, dry location. Dust, dirt,

and moisture can accumulate on the weighing sensors

and electronics causing innacuracy or malfunction.

• Avoid using your scale in close proximity to strong

radio wave emitting devices such as computers, cash

registers, and cordless phones.

• Always weigh on a at and level surface, free from

vibrations and drafts. The corner of a room is usually

the most stable.

• Gently apply all items to be weighed. Do not drop

items onto the weighing platform.

• Avoid dropping your scale. The warranty does not

cover damage due to rough treatment or overload.

I. OPERATION

Place Scale on a horizontal at surface.

1. Press [

ON/OFF

] key.

2. Wait until "0.0” or "0.00" is displayed.

3. Place the object(s) on the weighing platform.

4. By pressing the [

UNITS

] key, you can switch

between weighing units.

5. By pressing the [

LIGHT

] key, you can switch the

back-light on or off.

6. The removable lid can also be used as a weighing

tray.

II. TARE WEIGHING

1. Turn on scale as described above.

2. Place a tray or container on the scale platform.

3. Press [ TARE

] and wait until "0.0" or "0.00" is

displayed.

4. You can now add items to the container or tray to

obtain just the weight of the contents.

III. PARTS COUNTING

All object must be of equal weight for counting to work.

1. Turn on scale as described above.

2. Place a sample quantity (25, 50, 75, or 100pcs) of

the material you want to count on the platform

3. Press and hold the [ PCS

] key for 2 seconds until a

number is displayed (ie. 100pcs).

4. Press [

UNITS

] to change the sample quantity to

match the number you have on the platform.

5. Press the [ PCS

] key again to conrm the number.

6. You may now remove the sample quantity and add

any amount of the material to the platform, and the

display will show a count.

7. You can switch between weighing and counting

mode by pressing [ PCS

] or [ UNITS

] respectively.

IV. CALIBRATION

Calibration is NOT required before rst use. Only

calibrate if scale is not weighing properly.

**The CP3-650 calibrates with a 500g weight (not

included). The CP3-100 calibrates with a 100g weight

(not included)**

1. Turn the scale ON.

2. Hold the [ UNITS

] key for a few seconds. The

display will show "CAL".

3. Press the key again. "CAL" will ash, followed by

the required calibration weight (ie. 500g).

3. Place the calibration weight onto the platform.

4. The display will show "PASS" then return to normal

weighing mode. Calibration is complete!

V. TROUBLESHOOTING

[Display] Elimination of errors

-----------------------------------------------

[OUT2] Recalibrate the scale (Section IV).

[EEEE] You are overloading the scale. Remove the

excessive load immediately!

[un2T] Use the scale in a more stable position

Model CP3-650 CP3-100

Capacity 650.0g

22.92oz

20.89ozt

417.95dwt

100.00g

3.527oz

500ct

1543.2gn

Resolution 0.1g

0.01oz

0.01ozt

0.1dwt

0.01g

0.001oz

0.05ct

0.1gn

Weighing Units g, oz, ozt, dwt g, oz, ct, gn

Calibration Weight (not Included) 500g 100g

Platform Dimensions (inches) 2.0 x 2.7 “ Stainless Steel

Scale Dimensions (inches) 4.5 x 2.4 x 0.5”

Power 2 x CR2032 Batteries (included)

Warranty 10 Year Warranty

Specications

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AWS Skala Handbücher

Beliebte Skala Handbücher anderer Marken

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung

Fidelity Electronics

Fidelity Electronics G2e Bedienungsanleitung