Azbil MY6050A1001 Bedienungsanleitung

AB-6721

Specifications/Instructions

Direct Coupled Damper Actuator

Model MY6050A1001

General

Model MY6050A1001 direct coupled damper actuator is a

motorized actuator to open/close a damper. Model

MY6050A1001 provides 2-position or floating control in

response to a command from a controller. Combined with a

Model QY9010A1014 auxiliary potentiometer, Model

MY6050A1001 provides proportional control in response to a

command from a proportional controller.

Features

•Manual open/close function allows easy adjustment

without power supply.

•Standard models are equipped with rotation angle

adjuster (mechanical stopper), enabling to adjust motor

operating position.

•Low power consumption allows energy conservation.

•Large torque is assured despite compact, lightweight

design.

•Simple physical structure facilitates installation on most

types of the damper shafts.

•Optional auxiliary devices offer a variety of applications.

•Model MY6050A1001 is user-friendly to operate as well

as to install and set up.

•Model MY6050A1001 damper actuator conforms to all

the applicable standards of CE Marking.

AB-6721

Safety Instructions

Please read instructions carefully and use the product as specified in this manual. Be sure to keep this manual near by for ready

reference.

Usage Restrictions

This product is targeted for general air conditioning. Do not use this product in a situation where human life may be affected. If

this product is used in a clean room or a place where reliability or control accuracy is particularly required, please contact Azbil

Corporation’s sales representative. Azbil Corporation will not bear any responsibility for the results produced by the operators.

WARNING

•Do not disassemble the product. Electrical shock or equipment damage may occur.

•Operate the product within the service life, and avoid application that keeps product operating cycle excessively

frequent. Overuse of the product may cause fire or product damage.

CAUTION

•Installation and wiring must be performed by qualified personnel in accordance with all applicable safety

standards.

•This product must be operated under the operating conditions (power, temperature, humidity, vibration, shock,

installation position, atmospheric condition, etc) specified in this manual to prevent equipment damages.

•This product must be operated within its rated operating ranges specified in this manual. Failure to comply will

cause equipment damages.

•Do not install the product in a location with high temperature radiation. High temperature radiation may result in an

actuator malfunction.

•Do not put heavy load on the product. It may get damaged.

•All wiring must comply with local codes of indoor wiring and electric installation rules.

•This product does not have a power switch. Be sure to provide a power circuit breaker in the power source.

•To prevent product damage, always disconnect the power supply from the product before performing any wiring

and installation.

•Make sure all the wires are tightly connected. Incomplete connection may result in an actuator malfunction.

•To prevent personal injury, do not touch the moving part of the product in operation.

•Dispose of this product as an industrial waste according to the local regulations. Do not recycle all or part of this

product.

AB-6721

Specifications

Item Specification

Model number MY6050A1001

Action 2-position / floating action /

proportional action in combination with the auxiliary potentiometer Model QY9010A1014

Power supply voltage 24 V AC ±20 %, 50 Hz/60 Hz

24 V DC ±10 %

Power consumption 2 W, 4 VA (in operation)

Inrush current 5 A or less

Rotating angle Max. 95°(mechanical limit)

Operating time Approx. 150 s

Torque at the rated voltage 20 N⋅m

Holding torque 16 N⋅m

(Torque to hold the damper in a given position for floating or proportional action)

Ambient operating conditions -20 °C to 50 °C, 95 %RH or less (non-condensing)

(This product is not rain-proof and thus is for indoor use only.)

Transport/storage conditions -20 °C to 60 °C, 95 %RH or less

Enclosure rating Dust proof and drip-proof equivalent to IEC IP54

(Cable conduit must be facing downward.)

Cable 0.75 mm2×3-cores, 1 m long

Material / Color PC-GF10 / Silver gray

Weight Approx. 1.05 kg

Applicable damper shaft Circular: φ10 mm to φ20 mm, 42 mm long or longer

Square: 10 mm diagonal to 20 mm diagonal, 42 mm long or longer

Accessories •M4 tapping screws ×2

•Position indicator ring ×1

•Universal bracket ×1

•Installation instruction sheet ×1

Auxiliary devices

(Separate order is required.)

•Power transformer: Model AT72-J1

•Auxiliary potentiometer*1: Model QY9010A1014

•Auxiliary switch (SPDT ×1)*1: Model QY6051A1001

•Auxiliary switch (SPDT ×2)*1: Model QY6051B1001

•Mounting bracket for replacement (for replacing Model MY6040A)*2: Model Z-SMA

Requirements for order •Product model number (Model MY6050A1001)

•Auxiliary device model number (if necessary)

Notes:

∗1. Multiple auxiliary switches or auxiliary potentiometers cannot be connected. Connect single auxiliary potentiometer or auxiliary switch.

∗2. Mounting dimensions of Model MY6050A are different from those of Model MY6040A (former model). For replacing Model MY6040A with

Model MY6050A, the mounting bracket Model Z-SMA allows no change of the universal bracket mounting position.

AB-6721

Dimensions

Actuator

Figure 1. Dimensions (mm): Damper actuator

23 99

14.5 5.1

3.6

4.2

30 100.6

5.2

37.5 37.5

25.5 25.5

30 108.5

63.4

138.5

200

Maintenance clearance

100

Maintenance

clearance

100

Maintenance

clearance

100

Maintenance

clearance

AB-6721

Universal bracket

Figure 2. Dimensions (mm): Universal bracket

Parts Identification

Figure 3. Parts identification

180

11 12

4.3

2 pan-head tapping screws (slotted, M4 ×12, 1.4 pitch)

equivalent to JIS* B 1115-1976 are attached to the

universal bracket.

∗JIS: Japanese Industrial Standards

Position indicator ring

Fastening nut

M6 screw

(width across flats: 10 mm)

Shaft clamp

Rotation angle adjuster (mechanical stopper)

Rotary switch

(for rotating direction changeover)

Gear release button

AB-6721

Installation

CAUTION



•To prevent product damage, always disconnect

the power supply from the product before

performing installation.

IMPORTANT:

•

void application that keeps product operating

cycle excessively frequent.

•Meet the rotating direction of the actuator with the

damper rotating direction.

•Tighten the screws so that the actuator is securely

assembled with the damper.

•For the product installation, secure maintenance

clearance shown in Fig. 1.

Installation procedure

1) Fully close the damper shaft.

Figure 4. Damper shaft

2) Fully close the actuator Model MY6050A, and mount it

to the damper shaft. Finger-tighten the fastening nuts of

the shaft clamp to temporarily fix the actuator.

Figure 5. Temporal installation of the actuator body

3) With the gear release button pressed , manually rotate

the shaft clamp until it is in the position shown in Fig. 6.

Then, insert the universal bracket into the slit of the

actuator and fix the bracket onto the damper with the two

M4 tapping screws.

Figure 6. Attaching the universal bracket

4) Manually rotate the shaft clamp back to the fully closed

position with the gear release button pressed. At this

time, be sure to leave a clearance (approx. 1 mm)

between the shaft clamp and the rotation angle adjuster

(mechanical stopper). Using a wrench, tighten the

fastening nuts of the shaft clamp to completely fix the

actuator.

Figure 7. Complete installation of the actuator body

5) Attach the position indicator ring to the damper shaft so

that the tip of the damper blade and the pointer of the

indicator ring point to the same direction.

Adjust the rotation angle adjuster on the fully open side

depending on the damper rotating angle.

Figure 8. Attaching the position indicator ring

2. Finger-tighten.

1. Mount.

1. Press.

3. Insert.

Universal bracket

M4 tapping screws

2. Rotate.

1. Press.

2. Rotate to close.

3. Tighten.

1 mm

Tip of the

damper blade

Pointer of the

indicator ring

Damper blade and indicator ring

in fully closed position

Damper blade

1. Attach.

2. Adjust.

65°

10 to 20 mm

Damper shaft

Rotate to close.

Damper shaft diameter

Damper blade

in fully closed position

AB-6721

Wires Connection

Connect the lead wires as follows:

Figure 9. Lead wires connection and the actuator operating direction

Connection example for single actuator

<2-position or floating action>

Figure 10. Connection example: Single actuator for 2-position/floating action

Figure 11. Connection example: Single actuator for proportional action

IMPORTANT:

•For Model R30/R31/R35/R36/SDC40 single loop controller (Model with MFB* input) connected to Model

MY6050A1001, automatic setting function of feedback potentiometer is not available. Manually perform the

potentiometer setting. ∗MFB: Motor feedback

•For the controller with time-limit feedback connected to Model MY6050A1001, error may be detected. In such

a case, reset longer time limit.

∼(+)

24 V AC

(24 V DC)

⊥(-)

Model MY6050A1001

Rotary switch position

Operating direction

0 1 0 1

Wiring numbe

(printed on the insulation jacket of the lead wires.)

Manual switch /

Relay contact /

2-position controller /

Floating controller /

Proportional controller /

or the like

Model MY6050A1001

2-position controller/

floating controller

∼(+)

24 V AC

(24 V DC)

⊥(-)

Model MY6050A1001

with Model QY9010A1014

Proportional controller

(floating with relay contact output)

∼(+)

24 V AC

(24 V DC)

⊥(-)

S1 S2 S3

AB-6721

Specifications are subject to change without notice.

Building Systems Company

http://www.azbil.com/

Rev. 1.1 Jun. 2012 AB-6721

(J: AI-6721 Rev. 1.2) Printed in Japan.

Connection example for multiple actuators (in parallel operation)

Precautions for parallel operation

•Confirm the total power supply voltage of the actuators to operate in parallel.

•Operating time of each damper may differ due to error. This may result in difficult synchronization of the actuators

operation.

•Parallel operation of the multiple actuators may affect the operation life of the controller contact.

•Due to different operating time, Model MY6050A actuators cannot be combined with Model MY6040A actuators.

<2-position or floating action>

Figure 12. Connection example: Multiple actuators (in parallel operation) for 2-position/floating action

Figure 13. Connection example: Multiple actuators (in parallel operation) for proportional action

2-position controller/

floating controller

Model MY6050A1001

∼(+)

24 V AC

(24 V DC)

⊥(-)

Model MY6050A1001

with Model QY9010A1014

Proportional controller

(floating with relay contact output)

Model MY6050A1001

∼(+)

24 V AC

(24 V DC)

⊥(-)

Inhaltsverzeichnis

Andere Azbil Controller Handbücher

Azbil

Azbil C15 Bedienungsanleitung

Azbil

Azbil RA890G Bedienungsanleitung

Azbil

Azbil Azbil MIZCON Plus Bedienungsanleitung

Azbil

Azbil Infilex VC Bedienungsanleitung

Azbil

Azbil AUR455 Bedienungsanleitung

Azbil

Azbil Infilex GC WY5111 Bedienungsanleitung

Azbil

Azbil C45 Bedienungsanleitung

Azbil

Azbil Infilex ZM WY5322 Bedienungsanleitung

Azbil

Azbil DCP31 Bedienungsanleitung

Azbil

Azbil INFILEX GC WY5311 Bedienungsanleitung

Azbil

Azbil C36 Bedienungsanleitung

Azbil

Azbil KFPA Bedienungsanleitung

Azbil

Azbil AB-7352-U Bedienungsanleitung

Azbil

Azbil SDC45 Bedienungsanleitung

Azbil

Azbil RA1B Bedienungsanleitung

Azbil

Azbil Infilex WY5317C Bedienungsanleitung

Azbil

Azbil DMC10E Bedienungsanleitung

Azbil

Azbil KZ03 Series Bedienungsanleitung

Azbil

Azbil Intelligent Component Series Bedienungsanleitung

Azbil

Azbil C15 Bedienungsanleitung

Azbil

Azbil AUR450C Bedienungsanleitung

Azbil

Azbil C1M Bedienungsanleitung

Azbil

Azbil C15M Bedienungsanleitung

Azbil

Azbil C25 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch