Azbil MY8045A Bedienungsanleitung

AB-6682

Specifications/Instructions

Intelligent Component Series

Direct Coupled Damper Actuator

(Spring-Return Type)

Model MY8045A

General

Model MY8045A direct coupled damper actuator is a

motorized spring-return type actuator to open/close a

damper.

Model MY8045A communicates with a controller via SAnet

(Azbil Corporation’s communication protocol).

Features

•Intelligent Component Series Model MY8045A

communicates with a controller via SAnet, and thus

position control signal/position feedback signal is input to

/output from the controller.

•Manual open/close function allows easy adjustment

without power supply.

•Torque limit circuit inside the actuator automatically

stops the damper in fully closed or open positions.

•Low power consumption allows energy conservation.

•Large torque is assured despite compact, lightweight

design.

•Spring-return actuator automatically closes the damper

in 0 % position in case that the power is down.

•Rotary switch on the front surface easily changes the

motor rotating direction.

•Simple physical structure facilitates installation on most

types of the damper shafts.

•Model MY8045A damper actuator conforms to all the

applicable standards of CE Marking.

IMPORTANT:

This product is applicable to 50 Hz utility

frequency, not to 60 Hz utility frequency.

AB-6682

Safety Instructions

Please read instructions carefully and use the product as specified in this manual. Be sure to keep this manual near by for ready

reference.

Usage Restrictions

This product is targeted for general air conditioning. Do not use this product in a situation where human life may be affected. If

this product is used in a clean room or a place where reliability or control accuracy is particularly required, please contact Azbil

Corporation’s sales representative. Azbil Corporation will not bear any responsibility for the results produced by the operators.

WARNING

•Do not disassemble the product. Disassembly may result in electrical shock or equipment damage.

CAUTION

•This product must be operated under the operating conditions (power, temperature, humidity, vibration, shock,

installation position, atmospheric condition, etc) specified in this manual to prevent equipment damages.

•This product must be operated within its rated operating ranges specified in this manual. Failure to comply will

cause equipment damages.

•Operate the product within the service life, and avoid application that keeps product operating cycle excessively

frequent. Overuse of the product may shorten the product service life.

•Installation and wiring must be performed by qualified personnel in accordance with all applicable safety

standards.

•Do not install the product in a location with high temperature radiation. High temperature radiation may result in an

actuator malfunction.

•Do not put heavy load on the product. It may get damaged.

•All wiring must comply with local codes of indoor wiring and electric installation rules.

•This product does not have a power switch. Be sure to provide a power circuit breaker in the power source.

•To prevent product damage, always disconnect the power supply from the product before performing installation

and wiring.

•Make sure all the wires are tightly connected. Incomplete connection may result in an actuator malfunction.

•Do not touch the moving part of the product in operation to prevent personal injury.

•Dispose of this product as an industrial waste in accordance with your local regulations. Do not reuse all or part of

this product.

Trademark information:

ACTIVAL, Infilex, and savic-net are trademarks of Azbil Corporation in Japan or in other countries.

BACnet is a registered trademark of American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE).

AB-6682

System Configurations

Notes:

∗MIS may be used instead of SMS and DSS for your system. Note that MIS cannot be mixed with SMS or DSS in the same system.

∗Up to two SAnet I/F (interface) modules can be connected to one Infilex GC/Infilex GD.

∗For detailed specifications of SAnet, refer to Installation Manual of Intelligent Component Series for SAnet Communication

(AB-6713).

∗1 damper actuator or 1 ACTIVAL requires 1 SAnet address. 1 ACTIVAL PLUS requires 2 SAnet addresses.

Figure 1. System configuration example: SAnet connection in savic-net™FX system

Client PC

SCS

SMS

Infilex™AC

Model WY5117C

Infilex™GC

Model WY5111

Infilex™GD

Model WY5110

PMX-III

Model WY2001

Infilex

™

Model WY5205

Infilex

™

Model WY5206

Neopanel

Model QY7205

(Digital user terminal)

Neoplate Model QY7290

(Analog user terminal)

NC-bus (Max. 25 units and 500 m, but extendable up to 1000 m with the repeater module.)

SC-bus (Max. 50 units and 1000 m)

BACnet®/IP

Infilex

™

Model WY5207W

Neopanel

Model QY7205

(Digital user terminal)

DSS

MIS

SAnet

I/F

Intelligent Component

Series

ACTIVAL™

Infilex™ZM

Model WY5122

SAnet (Max. 15 addresses)

Intelligent Component

Series

Damper actuator

Display Panel

Intelligent Component

Series

ACTIVAL™PLUS

Temperature sensor

for pipe surface

DSS: Data Storage Server

MIS: Management Integration Server

PMX-III: PARAMATRIX™-III

SCS: System Core Server

SMS: System Management Server

AB-6682

Specifications

Item Specification

Model number MY8045A2001

Power supply voltage 24 V AC ±20 %, 50 Hz (Do not use this product at 60 Hz utility fequency.)

Power consumption 10 VA

Rotating angle Max. 95°

Operating time Motor: Approx. 150 s / Spring-return: Approx. 16 s

Torque at the rated voltage 15 N⋅m

Ambient operating conditions -20 °C to 50 °C, 10 %RH to 90 %RH (non-condensing)

Transport/storage conditions -20 °C to 60 °C, 95 %RH or less (non-condensing)

Enclosure rating IEC IP54 (dust-proof and splash-proof)

* This product is not rain-proof and thus is for indoor use only.

(Cable conduit must be facing downward.)

Cable 0.75 mm2×3 cores, 1 m long

Color Silver gray

Weight 2800 g

Applicable damper shaft Circular: φ10 mm to φ20 mm, 95 mm long or longer

Square: 10 mm diagonal to 16 mm diagonal, 95 mm long or longer

Accessories •M4 tapping screws ×2

•Universal bracket ×1 (Part No. 12596-0001)

•Mechanical stopper (Part No. ZDB-AF)

•Installation instruction sheet ×1

•Hexagon wrench ×1

Insulation resistance Between case and cable: 100 MΩor higher at 500 V DC

Withstand voltage Between case and cable: 500 V AC for 1 min., 1 mA or less

Control signal SAnet

Communication Transmission system Voltage transmission (SAnet)

(via SAnet) Transmission speed 1200 bps

Transmission distance Transmission distance varies depending on the number of devices and the type of devices

to be connected to. For details on the transmission distance, refer to Installation Manual

of Intelligent Component Series for SAnet Communication (AB-6713).

Function

Function Description

Data monitoring*1Following items can be monitored/operated from the host system (savic-net FX) and

Infilex GC / Infilex GD.

Damper position setting, damper position measuring

Adaption

(setting of rotation angle)

Rotation angle of the damper (controlled by the actuator) is adjusted with PC-MMI or with

Data Setter. (See P.10.)

Damper position

adjustment

Synchronisation*2

(position alignment)

Actual damper position and the position of the actuator are matched with PC-MMI, with

Data Setter, or when power is restored from blackout. (See P.10.)

Notes:

∗1 Above functions are available in combination with Infilex GC/Infilex GD and savic-net FX.

∗2 Positions of the actuator and of the damper are matched by fully closing the actuator and the damper.

Synchronisation at the time of power restoration is enabled/disabled by parameter setting.

AB-6682

Dimensions

Actuator

Figure 2. Dimensions (mm): Damper actuator

∗Clearance for maintenance

148.5

248

98 97.5

200*

100*

188

5.1

6.5

∗

Clearance for maintenance

2812.5

100*

188

80 9

100*

AB-6682

Universal bracket (Part No. 12596-0001)

Figure 3. Dimensions (mm): Universal bracket

∗Note:

Universal bracket is supplied with the product. Additionally order only when necessary.

Parts Identification

Figure 4. Parts identification

2 pan-head tapping screws (slotted, M4 ×12, 1.4 pitch)

equivalent to JIS* B 1115-1976 are attached to the

universal bracket.

∗JIS: Japanese Industrial Standards

229

R2.2

4 4 510

58.25

105

Service pin switch

(Manual switch)

AB-6682

Installation

CAUTION



•To prevent product damage, always disconnect

the power supply from the product before

performing installation and wiring.

IMPORTANT:

•Avoid application that keeps product operating

cycle excessively frequent.

•Meet the actuator rotating direction with the

damper rotating direction.

•Tighten the screws so that the actuator is securely

assembled with the damper.

•When installing this product, leave clearance for

maintenance as shown in Fig. 2.

Installation procedure: Min. 95 mm long shaft

Actuator with forward rotation (‘L’ side outward)

1) Mount the actuator with the ‘L’ side facing outward to the

damper shaft and temporarily tighten the hexagonal nuts

of the shaft clamp. Then, set the mounting position of

the universal bracket.

Figure 5. Installation of the actuator with forward rotation

to min. 95 mm long shaft (1)

2) Insert the universal bracket into the slit of the actuator

and fix the bracket onto the damper with the two M4

tapping screws.

Figure 6. Installation of the actuator with forward rotation

to min. 95 mm long shaft (2)

3) Confirm that the damper shaft is in fully closed position

and tighten the hexagonal nuts to completely fix the

actuator. Width across flats of the nuts is 10 mm.

Actuator with reverse rotation (‘R’ side outward)

1) Remove the C-clip from the shaft clamp and take out the

shaft clamp.

Figure 7. Installation of the actuator with reverse rotation

to min. 95 mm long shaft (1)

2) Turn over the actuator so that its ‘R’ side faces outward.

Refit the clamp in the actuator from the ‘R’ side, and then

attach the C-clip to fix the clamp.

Figure 8. Installation of the actuator with reverse rotation

to min. 95 mm long shaft (2)

3) Mount and fix the actuator to the shaft, referring to the

procedure of Actuator with forward rotation (‘L’ side

outward).

M4 screws

C-clip

1. Remove. 2. Take out.

Shaft clamp

Side ‘L’

Side ‘R’

1. Refit.

2. Attach.

Damper shaft

Damper blade

Forward rotation

indicator ‘L’

Universal bracket

Side ‘L’

Shaft clamp

Hexagonal nuts

AB-6682

Installation procedure: 20 mm to 95 mm long shaft

1) Remove the C-clip and take out the shaft clamp.

2) Attach the shaft clamp to the damper shaft, mount the

actuator to the clamp, and attach the C-clip to the shaft

clamp to fix the shaft clamp.

3) Mount the universal bracket with 2 M4 screws, and fix

the actuator.

Actuator with forward rotation (‘L’ side outward)

Figure 9. Installation of the actuator with forward rotation

to 20-95 mm long shaft

Actuator with reverse rotation (‘R’ side outward)

Figure 10. Installation of the actuator with reverse rotation

to 20-95 mm long shaft

Wiring

CAUTION

•To prevent product damage, always disconnect

the power supply from the product before

performing installation and wiring.

•This product is designed for 24 V AC power

supply voltage. Do not apply any other voltage

(e.g., 100 V AC, 200 V AC) to the product.

Connect the lead wires as follows:

∗Lead wire number

(indicated on each wire insulation)

Figure 11. Lead wires connection

For details regarding wires connection, refer to Installation

Manual of Intelligent Component Series for SAnet

Communication (AB-6713).

Side ‘L’

Black

SAnet

⊥

∼

24 V AC

Model MY8045A2001

1* 2* 5*

Red White

Side ‘R’

AB-6682

Address Setting (Addressing)

To SAnet interface module, the damper actuator Model MY8045A2001 and other Intelligent Component Series devices

including ACTIVAL and ACTIVAL PLUS are connected via SAnet. Set address for the terminal devices (Intelligent Component

Series devices) so that the SAnet interface module can recognize all the terminal devices connected. Follow the procedure

below to set the address. For details regarding address setting (addressing), ask our sales/service personnel.

Setting with service pin switch (manual switch):

1) Start addressing operation* of Data Setter or PC-MMI. Then, press the service pin switch to change the operating direction

as: L →R →L or R →L →R. Perform the operation within 5 seconds.

2) Address is set within 5 seconds after pressing the service pin switch.

∗Communication trouble and duplicated address cause addressing error. Check that address is correctly set in Data Setter or PC-MMI.

Setting based on SAnet ID:

With Data Setter or PC-MMI, enter the SAnet ID (on the SAnet ID label) and address number to set. The SAnet ID label is

attached on a side surface of the actuator, as shown in Fig. 12.

Figure 12. Locations of the labels

IMPORTANT:

Address setting must be performed by our service personnel or qualified expert.

Table 1. Basic address setting of this product and other Intelligent Component Series devices

Address. Device Sub-DO Sub-DI

1 Outdoor air damper

2 Exhaust air damper

3 Return air damper

4 Switch damper of total heat exchanger for outdoor air

5 Switch damper of total heat exchanger for exhaust air

6 Chilled/hot water valve / Chilled water valve Filter alarm

7 Hot water valve (Chilled water valve*) Humidifying ON/OFF

8 Humidifying valve

9 Reserved

A (10) Reserved

B (11) Reserved

C (12) Reserved

D (13) Reserved

E (14) Reserved

F (15) Reserved

Notes:

∗1. For ‘chilled/hot water valve + chilled water valve’ application, set 6 for chilled/hot water valve and 7 for chilled water valve.

∗2. Items in bold characters are the basic address to set for this product.

∗3. The above table is a basic setting example. Set address and use auxiliary I/O in response to system configuration, installation location,

wiring.

SAnet ID label

System indication label

AB-6682

System Indication Label

System indication label is attached to the front surface of the product. Write down the name of the SAnet system, host controller

number of the SAnet system, SAnet line number, and address.

Figure 13. SAnet system indication label

Adaption (Setting Rotating Angle)

CAUTION

•Before performing Adaption, check that the rotating direction of the product is correct.

When the rotation angle of the actuator is adjusted or changed, the actuator needs to memorize (adapt) the adjusted/changed

rotation angle. Note that Adaption is performed by our service personnel.

(To our service personnel: Refer to Engineering Manual of Intelligent Component Series for SAnet Communication (AB-6685))

Synchronisation (Position Alignment)

Damper position which the actuator controls disagrees with the actual damper position if actuator mounting position on the shaft

is changed. In such a case, the actuator requires Synchronisation so that the damper position controlled by the actuator and the

actual damper position agree (synchronize). Note that Synchronisation is performed by our service personnel.

(To our service personnel: Refer to Engineering Manual of Intelligent Component Series for SAnet Communication (AB-6685))

Setting of the Maximum Rotation Angle

To set the maximum rotation angle of the damper actuator to 90°or narrower, use the mechanical stopper supplied with the

product. The mechanical stopper allows to set every 5°increment within 30°to 90°range.

Setting procedure

1) Attach the mechanical stopper to a position according to the range to be set. Insert the mechanical stopper into grooves

provided on the damper actuator, as shown in the figure below.

2) Fix the mechanical stopper with the accessory tapping screw. There are 3 tapped holes (indicated with ‘x’) provided on the

scale of the damper position. Insert the tapping screw into either one of the holes, through the mechanical stopper.

Figure 14. Mechanical stopper

Write down the following.

•SYSTEM NAME:

System name or device number

•CON No.:

Host controller number

(Infilex GC/Inifilex GD number)

•SAnet No.:

SAnet line number

•ADDRESS:

SAnet address

System indication label

SAnet ID label

30 to 90°

Inhaltsverzeichnis

Andere Azbil Controller Handbücher

Azbil

Azbil C35 Bedienungsanleitung

Azbil

Azbil KFDB Bedienungsanleitung

Azbil

Azbil BC-R35 Series Bedienungsanleitung

Azbil

Azbil RA890G Bedienungsanleitung

Azbil

Azbil C15 Bedienungsanleitung

Azbil

Azbil INFILEX GC WY5311 Bedienungsanleitung

Azbil

Azbil Azbil MIZCON Plus Bedienungsanleitung

Azbil

Azbil C25 Bedienungsanleitung

Azbil

Azbil SLPC1F Bedienungsanleitung

Azbil

Azbil AUR455 Bedienungsanleitung

Azbil

Azbil AB-7352-U Bedienungsanleitung

Azbil

Azbil Infilex ZM WY5322 Bedienungsanleitung

Azbil

Azbil C36 Bedienungsanleitung

Azbil

Azbil Infilex FC Bedienungsanleitung

Azbil

Azbil Infilex FC Series Bedienungsanleitung

Azbil

Azbil BH-101G0W0000 Bedienungsanleitung

Azbil

Azbil Infilex VC Bedienungsanleitung

Azbil

Azbil Infilex AC WY5117C1 Series Bedienungsanleitung

Azbil

Azbil AUR890 Series Bedienungsanleitung

Azbil

Azbil C1M Bedienungsanleitung

Azbil

Azbil AUR890 Series Bedienungsanleitung

Azbil

Azbil RA1B Bedienungsanleitung

Azbil

Azbil C15M Bedienungsanleitung

Azbil

Azbil C7G Handbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch