Bang & Olufsen BeoLab 4 Bedienungsanleitung

BeoLab 4

Type 6650, 6652

Service Manual

English

German, French, Italian, Spanish, Danish, Dutch and Japanese versions

are available in the Retail System

This Service Manual must be returned with the

defective parts/back-up suitcase !

CONTENTS

Survey of modules ...................................................................... 1.1

How to service ......................................................................... 1.2

Warnings – Insulating test ........................................................ 2.1

Adjustments ............................................................................ 3.1

Repair tips ................................................................................ 4.1

Disassembly ............................................................................. 5.1

Speciﬁcation guidelines for service use ..................................... 6.1

Block diagram ........................................................................... 7.1

Wiring diagram ........................................................................ 7.2

Available parts ......................................................................... 8.1

1.1Survey of modules

PCB1 Ampliﬁer

PCB2 SMPS

PCB3 Filter

PCB4 LED

PCB5 Switch

PCB6 Input

Survey of modules

How to service

1.2

How to service

Front line service

BeoLab 4 is to be serviced in the customer’s home when it comes to electrical

symptoms or exchange of mechanical parts. In this way you avoid having to make

more than one visit and using minimum of time on the case, all for the beneﬁt of

the customer.

BeoLab 4 has been split-up into as few service items as possible. Each service friendly

item is packed individually, prepared for worldwide transport, and has a separate

seven digit spare part number to be found in the Bang & Olufsen Retail System or

the Service Manual. The exploded view drawing will show the service spare parts.

Back-up suitcase

A back-up suitcase contains all necessary electrical modules for front-line repair of

one loudspeaker. Cabinet parts must be ordered separately in the Retail System or

directly from B&O Struer DK.

The replaced modules must be returned for repair at Bang & Olufsen, Module

Repair Department. Use the Module Repair form or the form in the Retail Order

System, Exchange Module.

Delivery

As there is only one type number for BeoLab 4, the product can be used for all

markets with 100 to 240 Vac mains voltage. When you order BeoLab 4 (set of

two) this includes two mains cables, two Power Link cables and two boxes with

the three front covers in the chosen colour. This means that the delivery will

consist of four boxes.

This setup allows our packaging department to pack the speciﬁc order for the

customer no matter which country it goes to or the colour chosen.

Installation and setting-up

Only the switch for loudspeaker placement and the switch for Left or Right - Line

or PC must be set into correct position as described in the User Guide before

Power Link/Line signal and AC power wires are connected. If the Power Link is

used, the switch is for Left or Right setting. If Line connection is used (via mini-jack

plug) the switch is for Line (0 to 1V) or PC-line (0 to 2V) setting. See more details

in the User Guide. The automatic switch-off circuit is only active with the switch in

Line position, and is not active with the switch in PC-line position.

The LED will indicate on (green) or off (red) only.

Fault Finding

Before troubleshooting is initiated, let the customer demonstrate the fault, if possible.

There are four electrical modules in the product, and furthermore two additional

modules. One with a LED and one with a mini jack socket. Therefore a faulty module

is easy to point out in most cases. The PCB’s has been divided into the functionality:

Inputs, Ampliﬁer, Power supply and Filter.

No special service programs are available in this product or via the ServiceTool.

If there is a fault in the SMPS (PCB2) or Ampliﬁer (PCB1) the LED is typically off.

Only the tweeter unit is protected by a circuit that measures the resistance in the coil,

and will automatically turn down the signal level for the tweeter shortly if it is too

high for a period.

How to service 1.3

Replacement

Replacement of a loudspeaker unit or the ampliﬁer.

Each loudspeaker is individually adjusted from production to secure optimal stereo

perspective.

If a defective loudspeaker unit must be replaced, it is easily done without adjustment

due to the speciﬁcations of the unit.

Mechanics

All cabinet parts as e.g. the socket panel can be changed on-site. All surfaces can

be cleaned with a mild detergent.

Internal parts are supplied as service kits, e.g. the loudspeakers, PCB’s etc.

A product cover (soft) for service, black, can be ordered for transport of BeoLab 4.

2.1 Warnings – Insulating test

Warnings

ESD

When electrical replacements or disassembly is taking place, use an ESD-mat. The

internal electronics are very sensitive to static electricity.

Handling

Wear cotton gloves to avoid any ﬁngerprints on the product.

The surfaces on the product are very sensitive, so handling should be done with

great care to avoid damage.

Cleaning of the speaker surfaces should only be done with a lint-free cloth which

you have dipped in lukewarm water and wrung ﬁrmly.

Insulation test

The product must be insulation tested after having been dismantled. Make the test

when the set has been reassembled and is ready to be returned to the customer.

Flashover must not occur during the test.

Make the insulation test as follows:

Short-circuit the two pins of the mains plug and connect them to one of the

terminals of the insulation tester.

Connect the other terminal to ground on the Power Link socket.

NOTE!

To avoid damaging the product it is essential that both terminals of the insulation

tester have good contact.

During the test the current must not exceed 5 mA.

Slowly increase the voltage on the insulation tester until a voltage of 2.5 kV (ac) is

obtained. Maintain the voltage level for one second, then slowly decrease the

voltage to 0 V (ac).

STATIC ELECTRICITY

MAY DESTROY THE

PRODUCT

Adjustments 3.1

Adjustments

Adjustments after replacing PCB3 or PCB5

Read out the adjustment position of the old potentiometers, VR601 & VR701, and

set the new potentiometers to the same position.

PCB3 – VR601

PCB5 – VR701

VR601

VR701

4.1 Repair tips

Repair tips

Hum in loudspeaker when no music is played.

The Power Link cable must be of type MK III or higher.

The ground connection in Power Link cable lower than MK III may be insufﬁcient

for optimum sound performance.

The loudspeaker units can be checked by an ohm-meter (tweeter 5.7Ω ±10%;

woofer 6.7Ω ±10%).

Power Link

MK III

Disassembly 5.1

- Pull off front covers

Remove front cover

5.2 Remove woofer

TX20

- Remove screws

- Remove cables

Cables

- Pull off front cover

- Remove cables

ESD

PCB xx

ESD-Mat

Do not pull - release lock!

Andere Handbücher für BeoLab 4

Inhaltsverzeichnis

Andere Bang & Olufsen Sprecher Handbücher

Bang & Olufsen

Bang & Olufsen Beoplay P2 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beoplay M5 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEOLINK VIDEO Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEOPLAY A2 ACTIVE Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beovox RL Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beosound Explore Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beoplay A9 3rd Generation Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beolit 15 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEOLAB 28 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beolit 12 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 2 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 10 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 9 6217 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 2 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 2 3rd Generation Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 4 PC Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 3500 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 9000 MKIII Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 8000 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 5 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 12-3 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Celestial BOC60 Series Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 3 6881 Service-Handbuch

Bang & Olufsen

Bang & Olufsen BeoLab 7-4 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung