Banner Q3X Bedienungsanleitung

Laser Description and Safety Information

CAUTION: Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous radiation

exposure. Do not attempt to disassemble this sensor for repair. A defective

unit must be returned to the manufacturer.

Laser wavelength: 655 nm

Output: < 0.42 mW

Pulse Duration: 5 µs

Installation

Install the Safety Label

The safety label must be installed on Q3X sensors that are used in the

United States.

NOTE: Position the label on the cable in a location that

has minimal chemical exposure.

1. Remove the protective cover from the adhesive on the label.

2. Wrap the label around the Q3X cable, as shown.

3. Press the two halves of the label together.

Figure 3. Safety Label Installation

Sensor Orientation

Correct sensor-to-target orientation is important to ensure proper

sensing. To ensure reliable detection, orient the sensor as shown

in relation to the target to be detected.

For models with background suppression, make sure the intended

target is inside of the contrast sensing range and that any

background objects are positioned beyond the background

suppression distance.

Figure 4. Optimal Orientation of Target to Sensor

Q3X Laser Contrast Sensor

P/N 181486 Rev. E www.bannerengineering.com - Tel: +1-763-544-3164 3

Sensor-to-Background Position

Target Background

X = Diffuse Sensing Range

Y = Recommended

Background

Distance

Model Number X Y

LD50 50 mm (1.97 in) 60 mm (2.36 in)

LD100 100 mm (3.94 in) 120 mm (4.72 in)

LD150 150 mm (5.91 in) 190 mm (7.48 in)

LD200 200 mm (7.87 in) 280 mm (11.02 in)

Figure 5. Q3XBLD Contrast Detection versus Background Suppression

Sensor Mounting

1. If a bracket is needed, mount the sensor onto the bracket.

2. Mount the sensor (or the sensor and the bracket) to the machine or equipment at the desired location. Do not

tighten at this time.

3. Check the sensor alignment.

4. Tighten the screws to secure the sensor (or the sensor and the bracket) in the aligned position.

Wiring Diagram

10-30V dc

Input

Wire

Load

–

NOTE: Open lead wires must be connected to a terminal block.

Key

1 = Brown

2 = White

3 = Blue

4 = Black

5 = Gray

NOTE: The input wire function is user-selectable; see the Instruction Manual for details. The default

for the input wire function is off (disabled).

Cleaning and Maintenance

Handle the sensor with care during installation and operation. Sensor windows soiled by fingerprints, dust, water, oil, etc.

may create stray light that may degrade the peak performance of the sensor. Blow the window clear using filtered,

compressed air, then clean as necessary using 70% isopropyl alcohol and cotton swabs or water and a soft cloth.

Sensor Programming

Program the sensor using the buttons on the sensor or the input wire (limited programming options; see the Instruction

Manual for details).

In addition to programming the sensor, use the input wire to disable the buttons for security, preventing unauthorized or

accidental programming changes. See the Instruction Manual for more information.

Setup Mode

1. Access Setup mode from Run mode by pressing and holding MODE for longer than 2 seconds.

2. Use or to navigate through the top menu.

Q3X Laser Contrast Sensor

4 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 181486 Rev. E

Andere Handbücher für Q3X

Inhaltsverzeichnis

Andere Banner Zubehör Handbücher

Banner

Banner PresencePLUS P1B65Q Bedienungsanleitung

Banner

Banner L-GAGE LM Series Bedienungsanleitung

Banner

Banner iVu Plus TG Series Bedienungsanleitung

Banner

Banner Q4X Series Bedienungsanleitung

Banner

Banner Q4X Series Bedienungsanleitung

Banner

Banner L-GAGE LT7PIDQ Bedienungsanleitung

Banner

Banner Q4X Series Bedienungsanleitung

Banner

Banner Vision Sensor PA EDGE Bedienungsanleitung

Banner

Banner Q4X Series Bedienungsanleitung

Banner

Banner Q4X Series Bedienungsanleitung

Banner

Banner iVu Plus TG Gen2 Bedienungsanleitung

Banner

Banner Sensors T-GAGE M18T Bedienungsanleitung

Banner

Banner Q5X Bedienungsanleitung

Banner

Banner R-GAGE QT50R Series Bedienungsanleitung

Banner

Banner Q4X Series Bedienungsanleitung

Banner

Banner K30 Pro Bedienungsanleitung

Banner

Banner WORLD-BEAM Expert QS18E Series Bedienungsanleitung

Banner

Banner PresencePLUS P1B65Q Bedienungsanleitung

Banner

Banner L-GAGE LTF Bedienungsanleitung

Banner

Banner U-Gage Ultrasonic Sensor Bedienungsanleitung

Banner

Banner QM26 Series Bedienungsanleitung

Banner

Banner QS30 Series Bedienungsanleitung

Banner

Banner L-GAGE LE250 IO-Link Bedienungsanleitung

Banner

Banner iVu Plus BCR Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung