Baratza Sette 270 Bedienungsanleitung

Andere Handbücher für sette 270

6

Dieses Handbuch passt für folgende Modelle

1

Andere Baratza Kaffeemühle Handbücher

Baratza

Baratza Vario W+ Bedienungsanleitung

Baratza

Baratza Vario+ Bedienungsanleitung

Baratza

Baratza Encore Bedienungsanleitung

Baratza

Baratza VIRTUOSO+ Bedienungsanleitung

Baratza

Baratza Maestro Bedienungsanleitung

Baratza

Baratza Maestro Plus Bedienungsanleitung

Baratza

Baratza VIRTUOSO+ Bedienungsanleitung

Baratza

Baratza Vario Bedienungsanleitung

Baratza

Baratza Maestro Installations- und Benutzerhandbuch

Baratza

Baratza SETTE 30 Bedienungsanleitung

Baratza

Baratza Encore Bedienungsanleitung

Baratza

Baratza Vario+ Bedienungsanleitung

Baratza

Baratza sette 270 Installations- und Benutzerhandbuch

Baratza

Baratza Vario Bedienungsanleitung

Baratza

Baratza Encore Installationsanleitung

Baratza

Baratza Encore ESP Bedienungsanleitung

Baratza

Baratza Vario Bedienungsanleitung

Baratza

Baratza Maestro Bedienungsanleitung

Baratza

Baratza ENCORE & VIRTUOSO Bedienungsanleitung

Baratza

Baratza Virtuoso Bedienungsanleitung

Baratza

Baratza Maestro Bedienungsanleitung

Baratza

Baratza Forte AP Bedienungsanleitung

Baratza

Baratza Vario Bedienungsanleitung

Baratza

Baratza Vario Bedienungsanleitung

Beliebte Kaffeemühle Handbücher anderer Marken

Teesa

Teesa TSA4011 Bedienungsanleitung

tomado

tomado TM-1287 Bedienungsanleitung

Aicok

Aicok CG9220 Bedienungsanleitung

Zelmer

Zelmer ZCG7925 Bedienungsanleitung

Isomac

Isomac ROBY Bedienungsanleitung

Eldom

Eldom Dott MK60 Bedienungsanleitung

Bunn

Bunn SAFETY-FRESH 1 GPR Bedienungsanleitung

FAMITEC

FAMITEC BOLD Bedienungsanleitung

Santos

Santos SC55 Betriebsanleitung

Lumme

Lumme LU-2601 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi MC02 Bedienungsanleitung

Eureka

Eureka Zenith E Bedienungsanleitung

Bunn

Bunn HVG Gebrauchsanweisung

SEVERIN

SEVERIN KM 3878 Benutzerhandbuch

Bosch

Bosch SOLUTION 6000 Bedienungsanleitung

Imetec

Imetec MACINACAFFE Bedienungsanleitung

Bunn

Bunn POWDER AUTO FILL Gebrauchsanweisung

Judge

Judge JEA42 Bedienungsanleitung

1

Sette 270, 270W Fuse Replacement

Tools Needed: T-10 Torx (CAN USE 2mm hex key provided in shim kit that is included

with the grinder), Phillips Screw driver, Pliers (not necessary), Fuse*

*For 120v units: T3.15A250v Fuse

*For 220v units: T2.0A250v Fuse

*** Unplug the power supply cord from the rear of the machine. ***

2

1. Tilt the machine forward on a hand towel, resting the machine on its face

2. Remove the rear rubber foot (use pliers if needed)

3

3. Remove the four Torx screws from the rear of the machine, and the one Torx

screw that lies inside the rear foot slot. Screw positions indicated below. These

can be removed with the 2mm hex key that is included with the grinder’s shim kit.

4. Stand the machine back upright and gently pull the entire rear housing towards

the back of the grinder. There will be wires connected to the casing so be gentle.

4

Although the capacitor will be discharged unless there are extenuating circumstances,

exercise caution as it potentially has a high voltage charge that can shock you if both

contacts are touched.

5

5. There will be two wires attached the casing. I recommend leaving these wires

connected, but if the case is bothersome you can pull to remove the spade

connectors and set the case to the side.

6. Gently pry out the old fuse and replace it

Fuse (specs

above)

Bottom of grinder

6

Reassembly

1. (IF REMOVED) Slide the spade clips back onto the interlock switch.

*Pay attention to how the wires naturally want to sit. The wires will want to slide

on and lie in the grinder a certain way and if you put it back the way it came

apart, it will go together much easier.

7

2. Get the case roughly in position, as shown above

3. Work the case on such that it is flush with the sides and ready to slide forward

to finish installation

8

4. Alternate pushing on the bottom and on the top, as depicted above, to slide

the case the rest of the way forward into position.

5. Reinstall the screws and feet

If you have any questions or concerns, please email support@baratza.com or call at 425-641-1245.