Baxi BR660VA Bedienungsanleitung

5112253/01

OWNER GUIDE

This guide is intended to help you care for your gas fire. Please read thoroughly before

using and keep for future reference

This guide to be left with the owner

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).

WHEN CONVERTED USING CONVERSION KIT NO. 0591149 THIS

APPLIANCE IS FOR USE WITH PROPANE GAS (G31).

THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED

KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).

Model BR660VA

Heat Engine

POWER FLUE INSET GAS FIRE

(GC No. 32-032-44)

For technical advice firstly contact your retailer. If further advice is required then call

0161703 8157 for The Midlands and North or

01462 813 138 for The South.

Safety First.

This gas fire is CE Approved and designed to meet the appropriate British Standards

and Safety Marks.

Quality and Excellence.

This fire has been manufactured to the highest standards of quality and excellence and

was manufactured under a BS EN ISO 9001 quality system accepted by the British

Standards Institute.

The Highest Standards

The manufacturer is a member of the Society of British Gas Industries which works to

ensure high standards of safety, quality and performance.

Careful Installation

The manufacturer is a CORGI registered company. This gas fire must be

installed by a competent CORGI Registered Installer in accordance

with our Installer Guide and should not be fitted directly on to a

carpet.

Baxi Fires Division, Erdington, Birmingham B24 9QP

Because our policy is one of constant development and improvement, details may vary slightly from those

given in this publication

Page 2

OWNER GUIDE

LIST OF CONTENTS

Section Page

SAFETY 4

GAS CONSUMPTION 6

OPERATING YOUR FIRE 6

How to light your fire. 6

How to turn your fire off. 7

The flame sensing & flue blockage safety system. 7

CLEANING YOUR FIRE 8

Metal parts. 8

Ceramic fuel effect and burner compartment rear wall. 8

Ceramic burner. 9

Flue terminal. 9

Ventilation. 9

CERAMIC FUEL EFFECT REFITTING 9

MAINTENANCE 9

Regular maintenance. 9

Servicing. 10

This gas fire is designed to meet the most stringent quality, performance and safety

requirements to provide you with many years’ trouble-free service.

This guide aims to improve your understanding and appreciation of your gas fire by

providing simple and informative instructions to ensure that you benefit from the

excellent performance and features it has to offer.

Page 3

OWNER GUIDE

SAFETY

have the fire installed by a competent person. In the United Kingdom, installation

must be in accordance with the latest edition of the Gas Safety (installation & use)

Regulations. In the Republic of Ireland, installation must be in accordance with all

national and local regulations in force.

Do have the fire installed in accordance with the installer guide.

Do provide a minimum clearance of 700

mm from the top surface of the hearth to any

shelf made of wood or other combustible material where the shelf is not more than

150mm deep. For a shelf deeper than 150mm, add 12.5mm to the clearance for every

25mm of additional shelf depth.(See graph1)

Do Make sure that any combustible wall finish or cladding is removed from the area

Page 4

OWNER GUIDE

IF YOU SMELL GAS

DON’T SMOKE

EXTINGUISH ALL NAKED FLAMES

DON’T TURN ELECTRICAL SWITCHES ON OR OFF

TURN OFF THE GAS SUPPLY AT THE METER

OPEN DOORS AND WINDOWS TO GET RID OF THE GAS

IMMEDIATELY CALL THE GAS EMERGENCY SERVICE – SEE YOUR LOCAL TELEPHONE

DIRECTORY

Graph 1. Combustible shelf clearances

within the fascia and flanges of the fire box.

Switch the fire and fan off and allow to cool before attempting to clean, service, etc.

This appliance retains heat for some time after it has been switched off

Do always use a fireguard complying with BS 8423 for the protection of young

children, the elderly or infirm.

Do wait three minutes before attempting to relight if the fire is switched off or the

flames are extinguished for any reason.(Your fire is fitted with a safety device that will

automatically shut off the gas supply to the fire, if for any reason , the flame goes out)

Do get advice about the suitability of any wall covering near your fire. Soft wall

coverings (e.g. embossed vinyl, etc.) which have a raised pattern are easily affected by

heat. They may, therefore, scorch or become discoloured when close to a heating

appliance. Please bear this in mind whenever you are considering redecorating.

provide a minimum side clearance as below: The minimum allowable distance from

the outside of the appliance fascia to a corner wall having combustible material or any

other combustible surface which projects beyond the front of the appliance is 100mm.

For access purposes a 50mm clearance is recommended from non-combustible surfaces.

Please bear this in mind if ever you are altering the room.

Don’t hang clothing, towels or any other fabrics over the fire.

Don’t put more ceramic fuel effect pieces on the fire than the number given in this

guide or use any ceramic fuel effect pieces other than those authorised for this fire.

Adding extra fuel effect pieces could cause a safety hazard and consequent health

hazards.

Don’t put paper or other materials onto your fire.

Don’t use the fire with damaged base ceramics.

Don’t place any combustible material (rugs, carpet, plastic tiles, etc.) on the hearth

Don’t

attempt to clean or service the fire until it has been switched off and allowed to

cool completely.

Page 5

OWNER GUIDE

IMPORTANT :

THIS APPLIANCE MUST BE EARTHED

GAS CONSUMPTION

Model BR660VA

Has a maximum natural gas input of 6.0kW (Gross)

Has a maximum natural gas output of 3.1kW

Has a minimum natural gas input of 2.2kW (Gross)

Has a minimum natural gas output of 1.1kW

Model BR660VA when converted using kit number 0591149

Has a maximum propane gas input of 6.1kW (Gross)

Has a maximum propane gas output of 3.6kW

Has a minimum propane gas input of 3.6kW (Gross)

Has a minimum propane gas output of 1.8kW

OPERATING YOUR FIRE

How to light your fire.

The controls are shown in figure 1.

Check that the main isolating switch is on.

Remove the bottom front cover. The

controls are behind this cover

Check that the red indicator light is on

(this is located at the lower left hand side

of the burner).

Press and hold in the "ON" switch.

Within two seconds, the fan motor should

start and the indicator light should go out

Release the "ON" switch. The fan should

continue to run.

Depress the control knob and turn

partially to the "PILOT/IGN" position

Page 6

OWNER GUIDE

PLEASE NOTE

When operating your fire for the first time, some vapours may be given off which may

cause a slight odour and could possibly set off any smoke alarms in the immediate

vicinity. These vapours are quite normal with new appliances. They are totally harmless

and will disappear after a few hours use.

Figure 1.

until you feel some resistance.

Keep the knob depressed at this position for a few seconds to allow gas to flow to the

pilot.

While keeping the knob depressed, turn to the "PILOT/IGN" position. While turning, a

spark should light the pilot. The pilot flame can be seen through the ceramic fuel effect

at the front left side.

Keep the knob depressed at the "PILOT/IGN" position for a further ten seconds then

release it. The pilot flame should stay alight.

Slightly depress the knob and turn it to "LOW". Release the knob. Within a few seconds

the main burner should light at its low setting.

Slightly depress the knob and gradually turn it

towards "HIGH" until the burner is at your

desired setting. The burner flames will gradually

increase until the knob is at the "HIGH"

position.

If the spark ignition fails, the fire can be lit

manually by inserting a lighted taper into the

opening under the left hand coal pieces of the

front coal (as shown in figure 2) and depressing

the control knob at the "PILOT/IGN" position.

Note: If the fire goes out while setting the

control, repeat the full lighting procedure. If the

fire repeatedly goes out, have the fire serviced.

How to turn your fire off.

! To turn off the main burner but leave the pilot alight

slightly depress the control

knob and turn to "PILOT/IGN". Leave the fan switched on.

! To turn the fire fully off

slightly depress the control knob and turn to "OFF". Press

the "OFF" switch to turn the fan off. The indicator light will come on to show that the

electrical supply to the fire is live. If the fire is not likely to be used again for a long

time we suggest that the mains isolating switch for the fire is switched off.

! Wait at least three minutes after turning the fire off before relighting.

! While cooling, the coals may make some crackling noises. This is quite normal.

The flame sensing & flue blockage safety system.

! For your safety, this appliance is fitted with a flue blockage safety device which

will shut down the appliance in the event of abnormal flue conditions.

This device will also shut down the appliance if the pilot flame goes out due to lack

of oxygen or for any other reason.

Page 7

OWNER GUIDE

Figure 2. Lighting with a taper

The system includes a probe that senses the heat from the pilot flame. If this probe

is cool, the system will prevent any gas flow unless the control knob is kept depressed

at the "PILOT/IGN" position.

! The system also includes an atmospheric pressure detector. This will shut off the

gas supply if the fan is not working.

If there is a blockage preventing the flow of exhaust fumes out of the flue, the fan

will switch to a high boost speed to attempt to clear the blockage. If the boost speed

does not clear the flue, the pressure detector will shut off the gas supply.

! If the flames go out, or if for any reason the fire is turned off,

always wait at least 3

minutes before attempting to relight.

! If this device starts to shut off the gas frequently please get expert advice

! This device is NOT a substitute for an independently mounted Carbon

Monoxide detector.

CLEANING YOUR FIRE

Cleaning your fire.

To maintain the high performance and quality finish of your fire, please follow these

guidelines:

Before attempting to clean the fire, please remember to turn off the gas at the fire and

the electricity at the isolating switch.

Wait for the appliance to cool. The fire will retain heat for some time before cleaning

can begin.

Metal parts.

Clean the metal parts with a slightly damp cloth and then dry.

Do not use abrasive cleaners, as these will scratch the fire surface.

Ceramic fuel effect and burner compartment rear wall.

This product uses fuel effect pieces, gaskets and a burner compartment rear wall

containing Refractory Ceramic Fibres (RCF), which are man-made vitreous

silicate fibres. Excessive exposure to this material may cause temporary irritation

to eyes, skin and respiratory tract. Consequently, it makes sense to take care when

handling these articles to ensure that the release of dust is kept to a minimum.

Light coatings of soot will usually be burnt off during the normal operation of the

fire. Should any soot accumulation become excessive, the fuel effect pieces and

walls should be removed from the fire for cleaning. Cleaning should be carried out

in a well ventilated area or in the open air by gently brushing with the pieces held

away from your face so that you avoid inhaling the dust. We do not recommend the

use of a normal domestic vacuum cleaner which may blow dust back into the air.

We suggest that you remove the coals in the reverse order to that shown in the fuel

Page 8

OWNER GUIDE

installer and owner guide.

Ceramic burner.

Remove any soot or other foreign matter from the solid areas of the burner with a dry

soft brush.

Be careful not to brush any particles into the open slots.

Remove any particles from the slots with a vacuum cleaner fitted with a soft brush

attachment. Do not poke wire, etc. into the slots in the burner.

Flue terminal.

Keep the slots in the flue terminal on the outside wall clear of any obstructions (leaves,

snow etc.)

Ventilation.

If any purpose made ventilation was provided for this appliance, make sure that it is

always free from any obstruction.

CERAMIC FUEL EFFECT REFITTING

The installer and owner guide for the ceramic fuel effect is separate from this guide. The

installer may have attached it to this guide or placed it inside. It is important that the

installer and owner guide for the ceramic fuel effect is followed correctly. If replacing

the ceramic fuel effect, where a new guide is supplied, follow the installer and owner

guide supplied with the replacement fuel effect.

Keep the replacement installer and owner guide with this owner guide for future

reference.

MAINTENANCE

Regular maintenance.

In order to achieve and maintain high levels of personal safety and performance

efficiency, it is essential that the opening at the back of the fire and the flue are kept

clear of any form of obstruction. It is possible that deposits of mortar or soot could fall

and accumulate causing the flue to be blocked or restricted and so preventing proper

clearance of dangerous exhaust fumes.

In the United Kingdom it is the law that a landlord must have any gas appliance, flue

and pipework which is situated in a tenant's premises checked for safety at least every

twelve months by a competent person (In the U.K, a CORGI registered installer).

Page 9

OWNER GUIDE

Servicing.

IMPORTANT

To help us quickly help you, please try to have the following information available

before you contact us:

Type of fire.

Model/Name.

Serial Number.

You will also be asked for the fault, problem or request plus your Post Code.

! If you wish to replace any of the ceramic fuel effect pieces, spare parts

are available nationwide via the ‘interpart stockist network’. For your local

stockist consult Yellow pages under Central Heating.

! When fitting replacement parts it is important that only approved parts are

used for maximum safety.

Page 10

OWNER GUIDE

Inhaltsverzeichnis

Andere Baxi Kamin im Innenbereich Handbücher

Baxi

Baxi Wentworth Classic Benutzerhandbuch

Baxi

Baxi 946 Montageanleitung

Baxi

Baxi 739 Gebrauchsanweisung

Baxi

Baxi 951 Gebrauchsanweisung

Baxi

Baxi 759 Bedienungsanleitung

Baxi

Baxi 741 Montageanleitung

Baxi

Baxi 740FS Bedienungsanleitung

Baxi

Baxi 746 Montageanleitung

Baxi

Baxi Gallery Series Montageanleitung

Baxi

Baxi Bermuda SL3 Betriebsanleitung

Baxi

Baxi Wentworth Classic Benutzerhandbuch

Baxi

Baxi 748 Bedienungsanleitung

Baxi

Baxi EBONY SUPER Benutzerhandbuch

Baxi

Baxi 741FS Bedienungsanleitung

Baxi

Baxi Bermuda RG3 Betriebsanleitung

Baxi

Baxi churchill II 347 Bedienungsanleitung

Baxi

Baxi 739 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Baxi

Baxi Gallery Series Montageanleitung

Baxi

Baxi BERMUDA BBU HE Bedienungsanleitung

Baxi

Baxi Brava 4 Oxysafe Bedienungsanleitung

Baxi

Baxi 754 Montageanleitung

Baxi

Baxi 751 Montageanleitung

Baxi

Baxi Steel & Monaco 747 Montageanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch

Regency Fireplace Products

Regency Fireplace Products Pro Series Kurzanleitung