Be-Tech 3001D-1GL Bedienungsanleitung
3001DSmartSafeManual
For 3001D-1GL/3001D-3GL/3001D-5GL
SMART SAFE 3001D-1GL/3GL/5GL
SMART SAFE 3001D 1GL/3GL/5GL
1
SUMMARY
Thank you for using our company’s smart safe. Before you use this product, please read this manual carefully,
it will help you to use the smart safe in a correct way. Compare with the general safe, this smart safe will be
more securely and conveniently. Welcome to visit our web site, please contact us if you have any demands
and comments in our product.
SMART SAFE 3001D-1GL
SMART SAFE 3001D-3GL
SMART SAFE 3001D-5GL
SMART SAFE 3001D-1GL/3GL/5GL
SMART SAFE 3001D 1GL/3GL/5GL
2
ELECTRONIC PARAMETERS
Power supply: 4*AA alkaline batteries
Alarm voltage: DC 4.2V±0.2V
Static current: ≤30uA
Dynamic current: ≤400mA
Working temperature: 0℃~55℃
Working humidity: 20% ~ 93% ±2RH
SMART SAFE 3001D-1GL/3GL/5GL
SMART SAFE 3001D 1GL/3GL/5GL
3
NOTICES
Position the smart safe in a level and a covert area.
Place the smart safe in cool and dry place.
Avoid direct sunlight.
Do not dismantle the smart safe privately.
Do not tread on the smart safe.
Do not mix the different types of batteries or mix new batteries and the old batteries together.
Make sure that the positive and negative electrodes are connected correctly.
The man-made destruction is not on the warranty in the contract scope.
SMART SAFE 3001D-1GL/3GL/5GL
SMART SAFE 3001D 1GL/3GL/5GL
4
MATERIAL CONTAINED INSIDE THE PACKAGING
SMART SAFE 3001D-1GL/3GL/5GL
SMART SAFE 3001D 1GL/3GL/5GL
5
INSATLLATION
When you received the smart safe, you need to carry out some simple operations.
INTRODUCING BATTERIES
Remove the protective lid unscrewing the screws, and fit the batteries into their seats.
SMART SAFE 3001D-1GL/3GL/5GL
SMART SAFE 3001D 1GL/3GL/5GL
6
ASSIGNING IB CARD CODE
The safe needs an initial setting for the assignment of the IB card code which comes with it. This code varies,
depending on the IB card and must be assigned to the safe proceeding as follows.
Place the IB card against the receiver, an acoustic signal (“beep”) will confirm assignment of the code
NOTICE
When installing, always make sure that the IB card opens the safe.
POSITION
Now you can position the smart safe on the top of a piece of furniture, or inside a cabinet. Lock it in place
using the 2 wooden screw provided with the smart safe. For fastening in place, the smart safe has 4 through
holes –2 on the back wall and 2 on the horizontal surface. The installer should use these, at his own
discretion, depending on where the smart safe is to be placed.
SMART SAFE 3001D-1GL/3GL/5GL
SMART SAFE 3001D 1GL/3GL/5GL
7
DRILLING DIAGRAMS
SMART SAFE 3001D-1GL
SMART SAFE 3001D-3GL
SMART SAFE 3001D-5GL
SMART SAFE 3001D-1GL/3GL/5GL
SMART SAFE 3001D 1GL/3GL/5GL
8
USER INSTRUCTIONS
Now the smart safe is delivered to the user with the door open and ready to use.
ASSIGNING OWNER KEY
Make sure that the smart safe has been initialized.
Place an IB card against the receiver; an acoustic signal will confirm assignment of the card.
Only one owner key is allowed.
CHANGE AN OWNER KEY
Loose the screws of the back lock housing and remove the cover.
Press the Reset button of the PCB and follow the above procedure to assign a new owner key.
NOTICE
Once the owner key was deleted, the master key and the code will be deleted also.
ASSIGNING MASTER-KEY
Press */Cbutton, the display will show LIGHT_ON.
Place the owner key against the receiver, the display will show Pafter one beep.
Place the owner key against the receiver again.
Place another IB card against receiver, the display will show P_S1 after one beep, master key will
be confirmed assignment. (Master key assignment can be continue before display off, the display
will show P_S2…P_S5 till to FULL show on display)
DELETE SOME MASTER KEY
Press */C button, the display will show LIGHT_ON.
Place the owner key against the receiver, the display will show Pafter one beep.
Place the owner key against the receiver again.
Place a master key against the receiver, the display will show P_S1 after 2 beeps, the master key
will be deleted. (Master key can be deleted until the display off)
DELETE ALL MASTER KEY
Press */C button, the display will show LIGHT_ON.
Place the owner key against the receiver, the display will show Pafter one beep.
Place the owner key against the receiver two times again, the display will show P_ED, now all the
master key will be deleted.
CLOSING AND OPENING THE SAFE
To close the safe, the user must keep the door
pressed and key the code onto the keyboard,
followed by the key #. This code may consist
of anything between one and nine digits, at the
discretion of the user.
To indicate that the door has closed, a green
LED lights up in the receiver.
To open the safe, you just key in the same
code followed by the key #. As you set the
code, if you key in a wrong digit, you can press
* to delete it and write in the right digit.
You can change the secret code during any
safe closing or opening cycle.
SMART SAFE 3001D-1GL/3GL/5GL
SMART SAFE 3001D 1GL/3GL/5GL
9
USING THE IB CARD
If you forget the code when the safe is shut, you can open it again by using the IB card. To do so, process as
follows.
Place the IB card again the receiver, an acoustic signal (“beep”) will confirm the opening of the safe.
USING THE MECHANICAL KEY
In case of accidental loss of the IB card, or a fault on the electronic board, you can open the safe with the
mechanical key, proceeding as follows.
Take the front adhesive off from the door and put the mechanical key –provided with the product –into the
lock. You may now open the door manually.
NOTICE
Never leave the mechanical key and the IB card inside the safe.
ALARM FUNCTION
When someone key in the wrong code, after the third attempt, the safe will let out an acoustic alarm signal
lasting sixty seconds, and will be blocked.
After sixty seconds, the safe will keep quiet again.
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
