BEA MS08 RETROFIT Bedienungsanleitung

MAGIC SWITCH: MS08 RETROFIT

75.5821.00 MS08 RETROFIT 20141030 Page 1 of 4

Use of the device outside the intended application cannot be guaranteed by the manufacturer.

TECHNICAL SPECIFICATIONS *

DESCRIPTION

ENGLISH

Wireless1Activation | Touchless | Activation Sensor

10MS08UR

Includes single gang (shown) and double gang

faceplates and hardwired 900 MHz transmitter

* Speciﬁcations are subject to change without prior notice.

Technology Microwave

Detection Mode Motion (bidirectional)

Radiated Frequency 24.125 GHz

Radiated Power Density 5 mW/cm2

Supply Voltage 12-24 VAC +/-10% @ 50-60 Hz

12-24 VDC +30%/-10%

Current Consumption < 1.5 W

Output

Relay contact rating (max voltage)

Relay contact rating (max current)

Max switching power

Relay with switch-over contact (voltage free)

60 VDC / 125 VAC

1 A (resistive)

30 W (DC) / 60 VA (AC)

Detection Range 4-24 inches (adjustable)

Output Hold Time 0.5 s (in pulse mode)

Temperature Range -4°F to +131°F

Material ASA, Nylon, PC

Certication

Electromagnetic compatibility (EMC) according to 2004/108/EC

FCC: G9B-MS08 / 2ABWS-10TD900PB

IC: 4680A-MS08 / 4680A-10TD900PB

1The MS08 Retroﬁt Kit is designed to replace an existing, hardwired (2 wire), mechanical pushplate

with a touchless activation sensor. The exisiting 2 wires will be used to provide power to the sensor.

Screw

Faceplate

Microwave

Motion

Sensor

Screw

900 MHz Wireless Transmitter

2WIRING

PRECAUTIONS

Only trained and

qualiﬁed personnel

may install and setup

the sensor.

The warranty is invalid if

unauthorized repairs are

made or attempted by

unauthorized personnel.

Always test the proper

operation of the

installation before

leaving the premises.

The door control unit

and the door cover

proﬁle must be correctly

grounded.

1INSTALLATION

TIPS

APPLICATIONS

Single Swing Doors Dual Egress Swing DoorsSim Pair Swing Doors Sliding Doors

NOTE: Do not install the sensor within the swingpath of the door.

Page 2 of 4 75.5821.00 MS08 RETROFIT 20141030

single or double gang

electrical box may be

used (non-metallic

ideal)

plastic ring adapter may

be used to install double

gang faceplate onto

various mounting boxes

weather resistent foam

gasket may be used to

protect against weather

• PWR: Black - 12 to 24 VAC / VDC: -5% to +10%

• PWR: Red - 12 to 24 VAC / VDC: -5% to +10%

•NC: Empty - NC Contact

• NO: Green - NO Contact

• COM: White - Common at Door Control



Black - 12 to 24 VAC / VDC

Red - 12 to 24 VAC / VDC

White - Com at Door Control

Green - NO Contact

Empty - NC Contact

Connect the exiting 2 wires running through the wall (previously used for the activation relay of the

hardwired, mechanical pushplate) to the MS08 sensor’s PWR (black) and PWR (red) terminals. At

the door control, move the 2 wires from the activation circuit to power (see Technical Specications

for power information).

SENSOR

2WIRING (continued)

75.5821.00 MS08 RETROFIT 20141030 Page 3 of 4

SETTINGS & ADJUSTMENTS

4”

24”

MS08 Sensing Filed

Potentiometer

Output Mode Switch



24”

4”

Toggle Mode

Pulse Mode

DETECTION ZONE - potentiometer

COUNTERCLOCKWISE - decrease (4’’ minimum)

CLOCKWISE - increase (24’’ maximum *)

OUTPUT MODE - slide switch

PULSE - switch down

TOGGLE - switch up

* Maximum Detection Zone will

vary depending on size (area),

orientation, and speed of object as

well as environmental conditions.

SENSOR FUNCTIONALITY

TIMED MODE - Recommended for automatic door applications. In Timed Mode, a detection

activates the relay and the relay holds for a predetermined amount of time adjusted by the Output

Time potentiometer (1 to 30 seconds, counterclockwise - decrease, clockwise -increase).

TOGGLE MODE - Recommended for switch applications. In Toggle Mode, a detection activates the

relay and a second detection deactivates the relay. The relay will hold indenitely until a second

detection occurs.

For the 900 MHz wireless programming instructions, please reference BEA User’s Guide 75.5786

which comes with the 900 MHz wireless receiver (sold separately).

WIRELESS FUNCTIONALITY

The 900 MHz wireless transmitter (10TD900PB) comes prewired to the MS08 sensor’s NO (green)

and COM (white) terminals. The 900 MHz wireless transmitter is powered externally by two (2) AAA

batteries.

For the 900 MHz wireless programming instructions, please reference BEA User’s Guide 75.5786

which comes with the 900 MHz wireless receiver (sold separately).

WIRELESS

Sensor does not

seem to detect

1. Bad or no power 1. Check power supply

2. Detection range too short 2. Adjust detection zone

3. Incorrect wiring 3. Check wiring

Sensor stays in

detection

1. Envionmental conditions 1. Remove moving objects from around sensor

2. Incorrect wiring 2. Check wiring (NO and NC)

3. Wrong output mode 3. Switch output mode to pulse

TROUBLESHOOTING

Page 4 of 4 75.5821.00 MS08 RETROFIT 20141030

©BEA | Original instructions | 75.5821.00 MS08 RETROFIT 20141030

The complete declaration of conformity is available on our website: www.beasensors.com

Upon completion of the installation or service work, at a minimum, perform a daily safety check in accordance with the

minimum inspection guidelines provided by AAADM. Provide each equipment owner with an owner’s manual that

includes a daily safety checklist and contains, at a minimum, the information recommended by AAADM. Offer an

information session with the equipment owner explaining how to perform daily inspections and point out the location of

power/operation switches to disable the equipment if a compliance issue is noted. The equipment should be inspected

annually in accordance with the minimum inspection guidelines. A safety check that includes, at a minimum, the items

listed on the safety information label must be performed during each service call. If you are not an AAADM certified

inspector, BEA strongly recommends you have an AAADM certified inspector perform an AAADM inspection and place

a valid inspection sticker below the safety information label prior to putting the equipment into operation.

AAADM American Association of

Automatic Door Manufactures

ANSI / AAADM Compliance

24/7 Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: T[email protected] | Tech Docs: www.beasensors.com

FCC

FCC: G9B-21019

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by BEA Incorporated could void the user’s authority to operate the equipment.

Note:This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.These limits are designed

to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own

expense.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interfer-

ence, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

Inhaltsverzeichnis

Andere BEA Zubehör Handbücher