Beckhoff CP6207 0020 Series Bedienungsanleitung

Installation and Operating instructions for

Economy built-in Panel PC

CP6207-xxxx-0020

Version: 1.0

Date: 2019-09-09

Table of contents

Foreword 3

Notes on the Documentation 3

Liability Conditions 3

Trademarks 3

Patent Pending 3

State at Delivery 3

Delivery conditions 3

Description of safety symbols 4

Basic safety measures 5

Operator’s obligation to exercise diligence 6

Operator requirements 6

Product Description 7

Appropriate Use 7

Interfaces 7

Optional Interface 7

DVI (Digital Visual Interface) 7

USB-Interfaces 7

Network connection 7

Power supply 7

Ground connection 7

Access to the CF-Card and the Battery 8

Installation Instructions 9

Transport and Unpacking 9

Transport 9

Unpacking 9

Installation of the PC in the control cabinet 10

Installation in a control cabinet wall 10

Earthing measures 10

Mounting of the Panel PC 11

Power Supply Connection 12

Beckhoff power supply technology 12

Pin assignment of the connector 13

Fitting the cable 14

Material for assembling the connectors 14

Assembling the connectors 14

Connecting Power Supply 15

Cable Cross Sections 15

Configuration for shutting down the PC 15

PC_ON and Power Status functions 15

UPS output 15

UPS output function 15

Wiring diagram 16

Connecting devices 17

Connecting cables 17

Check voltage rating and connect 17

Operating Instructions 18

Switching the Industrial PC on and off 18

First switching on and driver installation 18

Operation 18

Servicing and maintenance 19

Cleaning the Industrial PC 19

Replacing the battery on the motherboard 19

Servicing 19

Emergency procedures 19

Shutting down 19

Disposal 19

CP6207-xxxx-0020 1

Table of contents

UPS Software Components (optional) 20

Installation on the PC 20

Help files 20

Troubleshooting 21

Fault correction 21

Beckhoff Support & Service 22

Beckhoff branches and partner companies 22

Beckhoff Headquarters 22

Beckhoff Support 22

Beckhoff Service 22

Appendix 23

Assembly dimensions 23

Technical data 24

Approvals 24

FCC: Federal Communications Commission Radio Frequency Interference

Statement 24

FCC: Canadian Notice 24

2 CP6207-xxxx-0020

Foreword

Notes on the Documentation

This description is only intended for the use of trained specialists in control and automation engineering

who are familiar with the applicable national standards. It is essential that the following notes and

explanations are followed when installing and commissioning these components.

The responsible staff must ensure that the application or use of the products described satisfy all the

requirements for safety, including all the relevant laws, regulations, guidelines and standards.

Liability Conditions

The documentation has been prepared with care. The products described are, however, constantly under

development. For that reason the documentation is not in every case checked for consistency with

performance data, standards or other characteristics. In the event that it contains technical or editorial

errors, we retain the right to make alterations at any time and without warning. No claims for the

modification of products that have already been supplied may be made on the basis of the data, diagrams

and descriptions in this documentation.

All pictures shown in the documentation are exemplary. Illustrated configurations can differ from standard.

Trademarks

Beckhoff®, TwinCAT®, EtherCAT®, Safety over EtherCAT®, TwinSAFE®, XFC®and XTS®are registered

trademarks of and licensed by Beckhoff Automation GmbH.

Other designations used in this publication may be trademarks whose use by third parties for their own

purposes could violate the rights of the owners.

Patent Pending

The EtherCAT Technology is covered, including but not limited to the following patent applications and

patents: EP1590927, EP1789857, DE102004044764, DE102007017835 with corresponding applications

or registrations in various other countries.

The TwinCAT Technology is covered, including but not limited to the following patent applications and

patents: EP0851348, US6167425 with corresponding applications or registrations in various other

countries.

©Beckhoff Automation GmbH & Co.KG.

The reproduction, distribution and utilization of this document as well as the communication of its contents

to others without express authorization are prohibited. Offenders will be held liable for the payment of

State at Delivery

All the components are supplied in particular hardware and software configurations appropriate for the

application. Modifications to hardware or software configurations other than those described in the

documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co.KG.

Delivery conditions

In addition, the general delivery conditions of the company Beckhoff Automation GmbH & Co.KG apply.

CP6207-xxxx-0020 3

Foreword

Description of safety symbols

The following safety symbols are used in this operating manual. They are

intended to alert the reader to the associated safety instructions.

Acute risk of injury!!

DANGER If you do not adhere the safety advise adjoining this symbol, there is

immediate danger to life and health of individuals!

Risk of injury!

WARNING If you do not adhere the safety advise adjoining this symbol, there is

danger to life and health of individuals!

Hazard to individuals!

CAUTION If you do not adhere the safety advise adjoining this symbol, there is

obvious hazard to individuals!

Hazard to devices and environment

Attention If you do not adhere the notice adjoining this symbol, there is obvious

hazard to materials and environment.

Note or pointer

Note This symbol indicates information that contributes to better understanding.

4CP6207-xxxx-0020

Foreword

Basic safety measures

Only switch the PC off after

closing the software

Before the Industrial PC is switched off, software that is running must

be properly closed.

Otherwise it is possible that data on the storage medium is lost. Please

read the section Switching the Industrial PC on and off.

Switch off all parts of the equipment, then uncouple the fieldbus

Attention

Before opening the housing of the PC, and whenever the PC is being

used for purposes other than plant control, such as during functional tests

following repair, all parts of the equipment must first be switched off, after

which the Industrial PC can be uncoupled from the plant.

Pulling out the fieldbus connection plug uncouples the PC (optional).

Items of equipment that have been switched off must be secured against

being switched on again.

The Industrial PC’s power supply unit must be supplied with 24VDC.

Do not open the power supply unit while voltage is applied!

CAUTION The supply voltage must be switched off before the power supply unit

housing is opened.

Do not exchange any parts when under power

Attention

When components are being fitted or removed, the supply voltage must

be switched off.

Fitting work on the Industrial PC can result in damage:

• if metal objects such as screws or tools fall onto operating circuit

boards.

• if connecting cables internal to the PC are removed or inserted

during operation.

• if plug-in cards are removed or inserted when the PC is switched

on.

High Voltage!

DANGER

Displays used for the control panel’s LC-display are operated with a

voltage of up to 1000 V, depending on type. For that reason:

The supply voltage must be disconnected before the housing of the

Control Panel is opened.

CP6207-xxxx-0020 5

Foreword

Operator’s obligation to exercise diligence

The operator must ensure that

• the Industrial PC is only used for its intended purpose (see chapter

Product Description).

• the Industrial PC is only operated in a sound condition and in

working order (see chapter Servicing and maintenance).

• the Industrial PC is operated, maintained and repaired only by

suitably qualified and authorized personnel.

• the personnel is instructed regularly about relevant occupational

safety and environmental protection aspects, and is familiar with

the operating manual and in particular the safety notes contained

herein.

• the instruction manual is in good condition and complete, and

always available for reference at the place of installation of the

Industrial PC.

• none of the safety and warning notes attached to the Industrial PC

are removed, and all notes remain legible.

• every user is familiar with all the functions of the software installed

on the Industrial PC to which he has access.

National regulations

depending on the machine

type

Depending on the type of machine and plant in which the Industrial PC is

used, national regulations governing the controllers of such machines will

apply, and must be observed by the operator. These regulations cover,

amongst other things, the intervals between inspections of the controller.

The operator must initiate such inspections in good time.

Do not open the housing of the build-in Panel PC

Note

For technical support contact Beckhoff Service.

Procedure in the event of a

fault

In the event of faults at the Industrial PC, the list in the section

Troubleshooting can be used to determine the measures to be taken.

Operator requirements

Read the operating

instructions

Anyone who uses the Industrial PC must have read these operating

instructions.

Software knowledge Every user must be familiar with all the functions of the software installed

on the Industrial PC to which he has access.

6CP6207-xxxx-0020

Product Description

Appropriate Use

The CP6207-xxxx-0020 build-in Panel PC is designed for industrial

application in machine and plant engineering. A steel plate housing with

aluminum front contains a TFT display with touch screen (optional). The

Industrial PC is installed in the front of control cabinets.

Do not use the Build-in Panel PC in areas of explosive hazard!

DANGER

The build-in Panel PC must not be used where there is a risk of explosion.

Interfaces

Optional Interface

X101

Optional interface

The Industrial PC can be fitted with an optional interface according to the

order option.

DVI (Digital Visual Interface)

X103

DVI out

The DVI connection is used for transferring the video signal.

DVI-D standard is supported.

USB-Interfaces

X104 – X107

USB out

The four USB interfaces are used for connecting peripheral devices with

USB connection. USB2.0 standard is supported.

Network connection

X108

LAN1

The RJ-45 connector allows the PC to be connected to a

10/100/1000BASE-T Local Area Network (LAN).

X109

LAN2

The RJ-45 connector allows the PC to be connected to a

10/100/1000BASE-T Local Area Network (LAN).

Power supply

X110

Power

The power supply for the Industrial PC is established via the socket.

Ground connection

Ground connection The Industrial PC is grounded via the stud bolt.

CP6207-xxxx-0020 7

Product Description

Access to the CF-Card and the Battery

Access to the CF-Card and

the battery

After solving the two crosshead screws (1) und (2), the cover cap can be

removed and allows access to the CF-Card and the battery.

cover cap 2

CF-Card Batterie

8CP6207-xxxx-0020

Installation Instructions

Transport and Unpacking

The specified storage conditions must be observed (see chapter Technical

data).

Transport

Despite the robust design of the unit, the components are sensitive to

strong vibrations and impacts. During transport, your Control Panel should

therefore be protected from excessive mechanical stress. Therefore,

please use the original packaging.

Danger of damage to the unit

Attention

If the device is transported in cold weather or is exposed to extreme

variations in temperature, make sure that moisture (condensation) does

not form on or inside the device.

Prior to operation, the unit must be allowed to slowly adjust to room

temperature. Should condensation occur, a delay time of approximately

12 hours must be allowed before the unit is switched on.

Unpacking

Proceed as follows to unpack the unit:

1.Remove packaging.

2.Do not discard the original packaging. Keep it for future relocation.

3.Check the delivery for completeness by comparing it with your order.

4.Please keep the associated paperwork. It contains important

information for handling the unit.

5.Check the contents for visible shipping damage.

6.If you notice any shipping damage or inconsistencies between the

contents and your order, you should notify Beckhoff Service.

CP6207-xxxx-0020 9

Inhaltsverzeichnis

Andere Beckhoff Touchscreen Handbücher

Beckhoff

Beckhoff CPX2719 Bedienungsanleitung

Beckhoff

Beckhoff CP770 140 Series Bedienungsanleitung

Beckhoff

Beckhoff CP37-1600 Series Bedienungsanleitung

Beckhoff

Beckhoff CP37-1600 Series Bedienungsanleitung

Beckhoff

Beckhoff CP65**-0060 Bedienungsanleitung

Beckhoff

Beckhoff CP6600 Bedienungsanleitung

Beckhoff

Beckhoff CP32-1600 Series Bedienungsanleitung

Beckhoff

Beckhoff CP6606-0001-0020 Bedienungsanleitung

Beckhoff

Beckhoff CP67 Series Bedienungsanleitung

Beckhoff

Beckhoff CP22 Series Bedienungsanleitung

Beckhoff

Beckhoff CP72 Series Bedienungsanleitung

Beckhoff

Beckhoff CP22 Series Bedienungsanleitung

Beckhoff

Beckhoff C9900-G070 Benutzerhandbuch

Beckhoff

Beckhoff CP7709 Bedienungsanleitung

Beckhoff

Beckhoff CP32-2 Series Bedienungsanleitung

Beckhoff

Beckhoff CP37 1600 Series Bedienungsanleitung

Beckhoff

Beckhoff CP6201 Bedienungsanleitung

Beckhoff

Beckhoff CP6700-0001-00 0 Series Bedienungsanleitung

Beckhoff

Beckhoff CP6600-0001-0020 Bedienungsanleitung

Beckhoff

Beckhoff CP27 Series Bedienungsanleitung

Beckhoff

Beckhoff CPX27 0010 Series Bedienungsanleitung

Beckhoff

Beckhoff CP32-2-0020 Series Bedienungsanleitung

Beckhoff

Beckhoff CP72 Series Bedienungsanleitung

Beckhoff

Beckhoff CP6606 Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung