Beckhoff ELX2792 Bedienungsanleitung
Operating manual | EN
ELX2792
Two Channel Relais Output Terminal, Solid State, potential
free, Ex i
2023-05-09 | Version: 1.0.0
Table of contents
ELX2792 3Version: 1.0.0
Table of contents
1 Foreword....................................................................................................................................................5
1.1 Notes on the documentation .............................................................................................................5
1.2 Safety instructions.............................................................................................................................6
1.3 Documentation Issue Status .............................................................................................................7
1.4 Marking of ELX terminals ..................................................................................................................8
2 Product overview ....................................................................................................................................12
2.1 ELX2792 - Introduction ...................................................................................................................12
2.2 Technical data.................................................................................................................................13
2.3 Intended use ...................................................................................................................................14
3 Mounting and wiring ...............................................................................................................................15
3.1 Special conditions of use for ELX terminals....................................................................................15
3.2 Installation notes for ELX terminals.................................................................................................15
3.3 Arrangement of ELX terminals within a bus terminal block.............................................................17
3.4 Installation position and minimum distances...................................................................................20
3.5 Installation of ELX terminals on mounting rails ...............................................................................21
3.6 Disposal ..........................................................................................................................................22
3.7 Connection ......................................................................................................................................23
3.7.1 Connection system........................................................................................................... 23
3.7.2 Wiring ...............................................................................................................................24
3.7.3 Proper line connection ..................................................................................................... 25
3.7.4 Shielding and potential separation ................................................................................... 25
3.7.5 ELX2792 - Connection and LEDs .................................................................................... 26
4 Appendix..................................................................................................................................................27
4.1 EtherCAT AL Status Codes ............................................................................................................27
4.2 UL notice .........................................................................................................................................27
4.3 Support and Service........................................................................................................................28
Table of contents
ELX27924 Version: 1.0.0
Foreword
ELX2792 5Version: 1.0.0
1 Foreword
1.1 Notes on the documentation
Intended audience
This description is only intended for the use of trained specialists in control and automation engineering who
are familiar with the applicable national standards.
It is essential that the documentation and the following notes and explanations are followed when installing
and commissioning these components.
It is the duty of the technical personnel to use the documentation published at the respective time of each
installation and commissioning.
The responsible staff must ensure that the application or use of the products described satisfy all the
requirements for safety, including all the relevant laws, regulations, guidelines and standards.
Disclaimer
The documentation has been prepared with care. The products described are, however, constantly under
development.
We reserve the right to revise and change the documentation at any time and without prior announcement.
No claims for the modification of products that have already been supplied may be made on the basis of the
data, diagrams and descriptions in this documentation.
Trademarks
Beckhoff®, TwinCAT®, TwinCAT/BSD®, TC/BSD®, EtherCAT®, EtherCATG®, EtherCATG10®, EtherCATP®,
SafetyoverEtherCAT®, TwinSAFE®, XFC®, XTS® and XPlanar® are registered trademarks of and licensed by
Beckhoff Automation GmbH. Other designations used in this publication may be trademarks whose use by
third parties for their own purposes could violate the rights of the owners.
Patent Pending
The EtherCAT Technology is covered, including but not limited to the following patent applications and
patents: EP1590927, EP1789857, EP1456722, EP2137893, DE102015105702 with corresponding
applications or registrations in various other countries.
EtherCAT® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH,
Germany.
Copyright
© Beckhoff Automation GmbH & Co. KG, Germany.
The reproduction, distribution and utilization of this document as well as the communication of its contents to
others without express authorization are prohibited.
Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a
patent, utility model or design.
Foreword
ELX27926 Version: 1.0.0
1.2 Safety instructions
Safety regulations
Please note the following safety instructions and explanations!
Product-specific safety instructions can be found on following pages or in the areas mounting, wiring,
commissioning etc.
Exclusion of liability
All the components are supplied in particular hardware and software configurations appropriate for the
application. Modifications to hardware or software configurations other than those described in the
documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.
Personnel qualification
This description is only intended for trained specialists in control, automation and drive engineering who are
familiar with the applicable national standards.
Description of instructions
In this documentation the following instructions are used.
These instructions must be read carefully and followed without fail!
DANGER
Serious risk of injury!
Failure to follow this safety instruction directly endangers the life and health of persons.
WARNING
Risk of injury!
Failure to follow this safety instruction endangers the life and health of persons.
CAUTION
Personal injuries!
Failure to follow this safety instruction can lead to injuries to persons.
NOTICE
Damage to environment/equipment or data loss
Failure to follow this instruction can lead to environmental damage, equipment damage or data loss.
Tip or pointer
This symbol indicates information that contributes to better understanding.
Foreword
ELX2792 7Version: 1.0.0
1.3 Documentation Issue Status
Version Comment
1.0.0 • Document structure updated
0.2 • Corrections
0.1 • First draft
Foreword
ELX27928 Version: 1.0.0
1.4 Marking of ELX terminals
Name
An ELX terminal has a 15-digit technical designation, composed of
• family key
• type
• software variant
• revision
example family type software variant revision
ELX1052-0000-0001 ELX terminal 1052: two-channel digital input terminal
for NAMUR sensors, Ex i
0000: basic type 0001
ELX9560-0000-0001 ELX terminal 9560: power supply terminal 0000: basic type 0001
Notes
• The elements mentioned above result in the technical designation. ELX1052-0000-0001 is used in
the example below.
• Of these, ELX1052-0000 is the order identifier, commonly called just ELX1052 in the "-0000" revision.
“-0001” is the EtherCAT revision.
• The order identifier is made up of
- family key (ELX)
- type (1052)
- software version (-0000)
• The Revision -0001 shows the technical progress, such as the extension of features with regard to the
EtherCAT communication, and is managed by Beckhoff.
In principle, a device with a higher revision can replace a device with a lower revision, unless specified
otherwise, e.g. in the documentation.
Associated and synonymous with each revision there is usually a description (ESI, EtherCAT Slave
Information) in the form of an XML file, which is available for download from the Beckhoff website.
The revision has been applied to the terminals on the outside, see Fig. ELX1052 with date code
3218FMFM, BTN 10000100 and Ex marking.
• The hyphen is omitted in the labeling on the side of the terminal. Example:
Name: ELX1052-0000
Label: ELX1052 0000
• The type, software version and revision are read as decimal numbers, even if they are technically
saved in hexadecimal.
Identification numbers
ELX terminals have two different identification numbers:
• date code (batch number)
•Beckhoff Traceability Number, or BTN for short (as a serial number it clearly identifies each terminal)
Date code
The date code is an eight-digit number given by Beckhoff and printed on the ELX terminal. The date code
indicates the build version in the delivery state and thus identifies an entire production batch but does not
distinguish between the terminals in a batch.
Structure of the date code: WWYYFFHH
WW - week of production (calendar week)
YY - year of production
FF - firmware version
HH - hardware version
Example with date code 02180100:
02 - week of production 02
18 - year of production 2018
01 - firmware version 01
00 - hardware version 00
Foreword
ELX2792 9Version: 1.0.0
Beckhoff Traceability Number (BTN)
In addition, each ELX terminal has a unique Beckhoff Traceability Number (BTN).
Ex marking
The Ex marking can be found at the top left on the terminal:
II 3 (1) G Ex ec [ia Ga] IIC T4 Gc
II (1) D [Ex ia Da] IIIC
I (M1) [Ex ia Ma] I
IECEx BVS 18.0005X
BVS 18 ATEX E 005 X
Examples
Fig.1: ELX2008-0000 with date code 2519HMHM, BTN 0001f6hd and Ex marking
Foreword
ELX279210 Version: 1.0.0
Fig.2: ELX9560-0000 with date code 12150000, BTN 000b000 and Ex marking
Inhaltsverzeichnis
Andere Beckhoff Touch-Terminal Handbücher
Beckhoff
Beckhoff EL10 Series Bedienerhandbuch
Beckhoff
Beckhoff KL31 2 Series Bedienerhandbuch
Beckhoff
Beckhoff KL6301-0000 Bedienerhandbuch
Beckhoff
Beckhoff EL34x3 Series Bedienerhandbuch
Beckhoff
Beckhoff KS3222 Bedienerhandbuch
Beckhoff
Beckhoff EL3773 Bedienerhandbuch
Beckhoff
Beckhoff KL2532 Bedienerhandbuch
Beckhoff
Beckhoff KL28 Series Bedienerhandbuch
Beckhoff
Beckhoff EL34 Series Bedienerhandbuch
Beckhoff
Beckhoff KL6904 Bedienungsanleitung
Beckhoff
Beckhoff EL3101 Bedienerhandbuch
Beckhoff
Beckhoff KL4011 Bedienungsanleitung
Beckhoff
Beckhoff KL2542 Bedienerhandbuch
Beckhoff
Beckhoff KL2535 Bedienerhandbuch
Beckhoff
Beckhoff KL6811 Bedienerhandbuch
Beckhoff
Beckhoff KL320 Series Bedienerhandbuch
Beckhoff
Beckhoff KL4494 Bedienungsanleitung
Beckhoff
Beckhoff EL1052 Bedienerhandbuch
Beckhoff
Beckhoff EL6692 Bedienerhandbuch
Beckhoff
Beckhoff EL1918 Bedienungsanleitung
Beliebte Touch-Terminal Handbücher anderer Marken
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung
Ingenico
Ingenico AXIUM EX4000 Bedienungsanleitung
Heisei Electronics
Heisei Electronics Q-POS 815 Bedienungsanleitung
Amano
Amano MTX-15 Bedienungsanleitung
FLOWBIRD
FLOWBIRD CWT Compact Touch Bedienungsanleitung
Demco
Demco SP7 Bedienungsanleitung
Motorola
Motorola MTP850 Bedienungsanleitung
YASKAWA
YASKAWA 62H-MDC0 Bedienungsanleitung
MVG industries
MVG industries NeptuLink Bedienungsanleitung
Price Industries Limited
Price Industries Limited FDC Gebrauchsanweisung
Honeywell
Honeywell TemaKey Bedienungsanleitung
EBN
EBN BPC65-B-A16G Bedienungsanleitung