Belkin F5D6230-3 Bedienungsanleitung

Belkin Components

501 West Walnut Street

Compton • CA • 90220 • USA

310.898.1100

Mac is a registerd trademark of Apple Computer, Inc. P73882

belkin.com

Belkin Components, Ltd.

Unit 13 • Gatelodge Close • Round Spinney

Northampton • Northants • NN3 8RX • United Kingdom

+44 (0) 1604678300

Belkin Components, Ltd.

7 Bowen Cresent • West Gosford

NSW 2250 • Australia

+61 (2) 4372 8600

Wireless

Cable/DS

Gateway Router

Quick Setup Guide for Mac®

F5D6230-3

Setting up the Router is accomplished in three easy steps:

1. Connect the Router to your network.

2. Configure your computer’s TCP/IP settings.

3. Configure the Router to your ISP’s settings.

Step 1: Connect the Router to your network

1. Power down your equipment.

2. Connect a network cable between each of your computers and the Router.

Connect each Mac to one of the ports on the rear of the Router labeled 1–3.

Do not connect a computer to the port labeled “WAN”.

3. Connect a network cable between the Router and your cable or

DSL modem.

Be sure this cable is plugged into the port labeled "WAN" on the Router.

4. Power on the cable or DSL modem.

BELKIN

GATEWAY

ROUTER

5. Select your connection type (this information is provided by your ISP) and click

"Select". Depending on your selection, you will see the "Static IP Address" page or

the "PPPoE" page. Enter the required values provided by your ISP and click "Enter".

6. The “MAC Cloning/Entry” screen will appear. If your ISP binds your connection to

the MAC address of your network adapter, click "Clone MAC Address" or enter the

MAC address here. Press “Enter”.

Your Router has been set up to communicate with your ISP.You should have Internet

access at this point. If you are having trouble, see the “Troubleshooting” section in the

user’s manual.

5. Connect the power adapter to the Router.

6. After the cable or DSL modem and the Router are turned on, the Router’s

WAN link light should be on. This indicates that the modem and the Router

are connected to each other.

7. Turn on the rest of your computers.

After your computers boot up, a LAN link light (on the front of the Router) will

be on for each port to which a computer is connected. These lights are your

means to verify that your computers are connected to the Router.

Step 3: Configure the Router to your ISP’s settings

1. Using the computer that was originally connected directly to the cable or DSL

modem, launch your browser. Note: You can access the setup utility from any

computer on the network, however, use the original computer for this procedure at

this time.

2. In the address bar, type the following address: 192.168.2.1.The Router login screen

will appear. Enter "Admin" in the User Name field, and do not enter anything in the

"Password" field. Click "OK".

3. The Router’s status page will appear.

4. Click on "Initial Setup" in the top left-hand corner. The following page will appear.

Step : Configuring TCP/IP for dynamic IP configuration

Your computer will communicate with the Router through TCP/IP. To configure

your Mac computer’s TCP/IP settings to communicate with the Router, follow the

steps below.

1. Pull down the “Apple” menu. Select "Control Panels" and select "TCP/IP".

2. At "ConnectVia:", choose either "Ethernet Built In" or "Ethernet" based on your

Mac computer’s interface.

3. At "Configure:" choose "Using DHCP Server".This will tell the computer to obtain

an IP address from the Router.

4. Close the window.The following window will appear. Click "Save".

5. Restart the computer.

You are now finished with dynamic IP configuration. Perform this operation for each

computer that you will be connecting to the Router.

When finished configuring yourTCP/IP settings, you need to start File Sharing to enable.

Andere Handbücher für F5D6230-3

Dieses Handbuch passt für folgende Modelle

Andere Belkin Netzwerk-Router Handbücher

Belkin

Belkin F9K1115V2 Bedienungsanleitung

Belkin

Belkin F5D7234-4 v5 Bedienungsanleitung

Belkin

Belkin F5D8636-4 v2 Bedienungsanleitung

Belkin

Belkin AX1800 Bedienungsanleitung

Belkin

Belkin TSG-UK-1-001 Referenzhandbuch

Belkin

Belkin F1PI241EGau Referenzhandbuch

Belkin

Belkin INVENTEL CONFIG XP Montageanleitung

Belkin

Belkin F5D8233-4v3 Bedienungsanleitung

Belkin

Belkin F5D5230 Bedienungsanleitung

Belkin

Belkin F9K1103 v1 Bedienungsanleitung

Belkin

Belkin F5D52314 - Cable/DSL Gateway Router Bedienungsanleitung

Belkin

Belkin F5D7230au4 Bedienungs- und Montageanleitung

Belkin

Belkin High Speed ADSL2+ Bedienungsanleitung

Belkin

Belkin TSG-UK-1-008 Referenzhandbuch

Belkin

Belkin OmniView 5000HQ Bedienungsanleitung

Belkin

Belkin F5D9630au4A Referenzhandbuch

Belkin

Belkin VISION N1 Bedienungsanleitung

Belkin

Belkin F5D92304 - Wireless G Plus MIMO Router Bedienungsanleitung

Belkin

Belkin F7D3301 Bedienungsanleitung

Belkin

Belkin 802.11g Wireless Ethernet Bridge Bedienungsanleitung

Belkin

Belkin P73928EH Bedienungsanleitung

Belkin

Belkin F5D8233 Bedienungsanleitung

Belkin

Belkin F506230-3 Bedienungsanleitung

Belkin

Belkin F5D7630 Kurzanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise