Belkin Bitronics F1U128-KIT Bedienungsanleitung
P73045 F1U128-KIT
Bitronics DualBus
Switch Kit
User Manual
1
Introduction
Features
Thank you for purchasing the Belkin Components Bitronics DualBus Switch
Kit! Now, you and your colleagues can share and select between two
different parallel devices from your desktop. And, if you are using
Windows®95, 98 or NT®, you will be able to take advantage of Bitronics
Software, which allows you to print automatically even if you have more
than one printer!
• Allows four computers to access any two parallel devices simultaneously
and independently
• Virtual Port printer driver software allows fully automatic printer selection
through Windows®95/98 and NT®
• File-transfer feature between two PCs compatible with Windows®Direct
Cable Connection, LapLink®and DOS Interlink™
• Includes two 6 ft. (1.8m) IEEE 1284-compliant cables to connect the computers
• Includes power adapter
• Adjustable timeout
Package Contents:
Bitronics DualBus Switch, 4-2 F1U128
Power Adapter, 9VDC, 600mA F1D065-PWR (US)
2 x IEEE 1284-compliant cables F2A047-06
User manual P73045
Registration card P72009
Other Parts Needed (if necessary)
• IEEE 1284 printer cable, Belkin Part# F2A046-XX. You will need this
cable to connect a printer to the autoswitch. Your current printer cables
may work, but IEEE-compliant cables are recommended.
• IEEE 1284 device cable, Belkin Part# F2A047-XX. You will need this
cable to connect a computer to the autoswitch.
NOTE: "XX" is the length in feet.
2
Compatible Standards:
IEEE 1284-1994 Parallel Port Communication Standard
Electrical:
Input Voltage 9VDC
Max Input Current 600mA
Max Power Consumption 5.4W
Max Heat Dissipation 0.31 BTU/min
Dimensions:
Width: 7.0” (17.8cm)
Height: 3.75” (9.5cm)
Depth: 1.25” (3.2cm)
Weight: 7.1 oz. (202 g)
Storage Temperature: -10ºC to 50ºC
(14ºF to 122ºF)
Operating Temperature: 0ºC to 40ºC
(32ºF to 104ºF)
Humidity: 0 to 95%
Non-condensing
Technical Specifications
3
DIP switch settings (located underneath switch):
SW1: Reset Switch
To reset, OFF→ON→OFF
SW2 and SW3: TimeOut Setting
TimeOut is the amount of time the switch remains locked on a PC port after
data transfer. Use a longer TimeOut when connecting to scanners, mass
storage devices and for large print jobs.
Product Detail
Device activity LEDs Connector to Device A Connector to Device B
Connector to PC2
PC activity LEDs
Recommended
Printer button
Computer button
DC power jack
(side)
Connector to PC3
ON DIP
1234
ON is UP. SW4 is not used.
SW2
ON ON 5 seconds
ON OFF 10 seconds
OFF ON 20 seconds
OFF OFF 40 seconds
SW3 TimeOut
Connector
to PC1 Connector
to PC4
In manual mode, you can select a port manually through the buttons on the
Bitronics switch. You can also use this mode in conjunction with software to
see your switch in action!
• Press COMPUTER to select which computer port you wish to configure or
monitor. For the computer connected to Port 1, press the COMPUTER
button until the LED on Port 1 is lit up either in red or green.
• Press the PRINTER button until the LED of the appropriate device port
you wish to use is lit up.
For example, if you want
computer 2 to use the
device on port B, press the
COMPUTER button until the
LED on "2" is lit up. Then,
press the PRINTER button
until LED "B" is lit up.
To use File Transfer mode, press the PRINTER button until the LED on the
computer port turns green. When the LED turns green, the port is ready for
file transfer mode. For file transfer mode to be successful for both PCs, both
computer ports must be set to file transfer mode – which is evident when the
LEDs next to 1 and 2 are green. For more information on File Transfer, please
see page 25.
Note: Computer 1 can only file transfer to computer 2, and computer
3 can file transfer to computer 4. If you change the ports
manually using the buttons, the changes made will not be
reflected in the software.
4
Manual Mode and Port Monitoring
Printer button Computer button
5
Windows®3.x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6
MS-DOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7
Windows®95/98 and NT®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8
NOTE: When installing software on any operating system, the
software must be installed on all the computers connected to
the Bitronics switch so that each machine can control the
switch properly.
Choose your operating system
6
Software installation: Windows®3.x
Insert the diskette labeled P27236 in your floppy drive. In the Program
Manager, click on File then click Run. In the space, type in "a:\setup.exe".
Follow the installation instruction prompts. After the setup program is done,
simply double-click on the correct icon to run the port selection program.
7
Software installation: MS-DOS
To switch port, simply click on the port letter of your choice, and your
computer will be connected to the device on the port chosen.
Software-Installation: MS-DOS
Enter the following at the DOS prompt and press ENTER:
Copy a:\dos\swport.com c:\SWPORT.com
SWPORT.com is a command-line executable. Please follow the syntax for
proper operation:
File Transfer in DOS and WINDOWS®3.x:
The file transfer feature of the Bitronics switch allows both computers to
connect a if there was a file transfer cable connected between them.
The LED of the corresponding computer port on the Bitronics switch will
turn green. This LED represents the computer you are on now, and is set for
file transfer mode.
The LED of the corresponding computer port on the Bitronics switch will
turn green. This LED represents the computer you are on now is set for file
transfer mode. Note that PC1 can only file transfer to PC2, and PC3 can
only file transfer to PC4. When both sets of PC LEDs on the Bitronics switch
are green, then the computers are ready for file transfer. At this point, the
cables and the Bitronics switch act as if it was a file transfer cable. You can
now run programs such as Windows‚ Direct Cable Connection, or LapLink®.
Please refer to their user manuals or websites for information on how to
configure their software. Just remember that your Bitronics switch setup
mimics the file transfer cable requirement.
8
BEFORE YOU INSTALL THE BELKIN BITRONICS SOFTWARE, YOU MUST
FIRST MAKE SURE THAT EACH DEVICE WORKS PROPERLY ON ITS OWN
WITH EACH COMPUTER. DO NOT CONNECT THE BITRONICS SWITCH TO
THE COMPUTERS OR INSTALL THE SOFTWARE UNTIL INSTRUCTED BY
THIS PROCEDURE!
1. Make sure that the printer port on your computer is set to ECP mode. To
do this, you must go into your computer’s BIOS or CMOS setup.
Instructions on how to do this differs from one computer to the next.
Please consult your computer manufacturer’s manual, tech support, or
website for information on how to do this. Please do not call Belkin Tech
Support regarding this because each computer’s BIOS setup routine is
different. Refer to the Appendices at the end of this manual for
information on several models of computers.
The BIOS setup routine prompt is displayed a few seconds after you turn
on your computer and hear its first beeps. Again, this varies from PC to
PC. Please consult the Appendices and/or your computer manufacturer’s
manual or their tech support for information on how to do this properly.
Usually you will see a message that reads PRESS DEL TO ENTER SETUP or
PRESS F2 TO ENTER SETUP. When in the setup program, there may be a
selection for "Integrated Peripherals", or "Peripheral Setup". Then, look
for "Parallel Port Type" or "LPT port type". Change that setting to say
"ECP" or "ECP/EPP". Save your settings then exit. When Windows®
restarts, it may find new hardware, and it may ask you for the Windows®
CD. Be prepared to insert the CD into the computer.
2. Make sure that the software and drivers for the devices to be shared are
properly installed on all computers.
For instance, if you are sharing a Zip®Drive and a printer between 2
computers, you will need to first connect and install the Zip®Drive drivers
on the first PC. Make sure that the Zip®Drive works perfectly on it, then
repeat the same installation process for the second PC. Then, you will
need to do the same installing the printer’s driver on both PCs as well.
This way, all the PCs have the drivers properly loaded so each one can
access either device without any problems, as if they were connected to
the computer individually.
Windows®95 / 98 and NT®
Andere Handbücher für Bitronics F1U128-KIT
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Belkin Schalten Handbücher
Belkin
Belkin F1DK102U - KVM Switch With Cabling Bedienungsanleitung
Belkin
Belkin Conserve Switch Bedienungsanleitung
Belkin
Belkin OmniView Secure KVM Switch Bedienungsanleitung
Belkin
Belkin OmniView SOHO F1DD102L Bedienungsanleitung
Belkin
Belkin F1DN104G Bedienungsanleitung
Belkin
Belkin F1DL102 Bedienungsanleitung
Belkin
Belkin OmniView F1DB102P2ea Bedienungsanleitung
Belkin
Belkin Bitronics AutoSwitch Kit Bedienungsanleitung
Belkin
Belkin OmniView F1DP104Aea Bedienungsanleitung
Belkin
Belkin OmniView F1DK102P Bedienungsanleitung
Belkin
Belkin OmniView F1DK102P Bedienungsanleitung
Belkin
Belkin OmniView SOHO Bedienungsanleitung
Belkin
Belkin OMNIVIEW P74696 Bedienungsanleitung
Belkin
Belkin F1DN104K-3 Bedienungsanleitung
Belkin
Belkin OmniView Dual-User PRO3 Bedienungsanleitung
Belkin
Belkin F1DF102U - Flip USB KVM Switch Bedienungsanleitung
Belkin
Belkin F5U261 Bedienungsanleitung
Belkin
Belkin OmniView Dual-User PRO3 Bedienungsanleitung
Belkin
Belkin P75341ej Bedienungsanleitung
Belkin
Belkin F1DL102UTT Bedienungsanleitung
