Bell Cocoon 500 Bedienungsanleitung

console 500

18-FUNCTION WIRELESS CYCLE COMPUTER

FUNCTIONS

WARNING:

Follow instructions

carefully. Make

certain that no part

of the computer

assembly interferes

with the brakes or

wheels. Check nuts

and bolts often to be

sure they are secure.

Cadence ( RPM)

Average Cadence ( RPM)

Speedometer (SPD) (0 TO 99.9 Km/hr or M/hr)

Tripometer (DST) (0 to 999.99 Km or M)

Odometer (ODO) (Up to 9999.9 Km or M)

Auto trip timer (TM) (9:59:59)

Maximum Speed (MXS) (0 to 99.9 Km/hr or M/hr)

Clock, 12/24 hour Selectable

Average Speed (AVS) (0 to 99.9 Km/hr or M/hr)

Speed Comparator (+ or -)

Speed Tendency

Odometer Program Function (ODO)

Auto Scan

Maintenance Required Functions ( )

Back-lite: Press any button, light will go on for a few seconds

Install Batteries

STEP 1

)

Computer — (Note: Battery is pre-installed) Remove the battery

cover from the bottom of the computer using a small coin.

Install the 3V battery with positive (+) pole facing the cover

(Figure 1a). If the LCD shows irregular gures, take out the

battery and install again. This will clear and restart the computer’s

microprocessor.

Battery is pre-installed.

Wheel Transmitter - (Note: Battery is pre-installed) Install the 12V

battery in the wheel transmitter with the positive (+) pole facing

the battery cap. Re-install the cap with a small coin and be sure it

is tight to prevent moisture leakage (Figure 1b).

Fig. 1a Fig. 1b

Computer Battery

(3V / CR 2032)

Transmitter Battery

(12V / VR22L)

1028 /A 23

Accessories

STEP 2

3V CR2032

AB C

D E F

G I

Front Wheel

Sensor

Installation

STEP 3

CR2032

Clamp the magnet onto the spoke of front wheel and attach

the transmitter to the right fork (right side when you stand in

front of bicycle) by using the cable ties as shown in Fig. 2.

The silver arrow on the transmitter must face towards the

wheel.

Make sure the arc of magnet intersects the alignment arrow on

the transmitter with 2 mm clearance as shown in Fig. 3.

G G

2mm Max

Mounting

Bracket

STEP 4

Handlebar Mount Stem Mount

BBH

CADENCE

Magnet

Installation

STEP 5

Crankarm

Top view

Pedal

CADENCE

Sensor

Installation

STEP 6

The silver arrow on the transmitter must

face towards the crankarm.

Top

View

2mm Max

HOW TO MEASURE WHEEL FACTOR

dxx

Press the Right Button to adjust the value of the rst

digit of the Wheel Factor. Once you have entered the

correct value, press the Left Button to conrm the value

and advance to the next digit. Repeat for all four digits.

Press the Left Button to advance to KM/MILE selection.

KM/MILES SELECTION: After wheel size has been input,

the Km/Miles units for distance and speed will ash.

Press the RIGHT button to choose between Kilometer

(KM) and Mile (M), press the LEFT button to conrm.

Press and hold LEFT and RIGHT buttons for

4 seconds to access wheel size input mode.

Note all information in computer will be erased.

The digits on the bottom row will ash. The

value you need to enter into the computer is

the Wheel Factor. Wheel

Factor is the circumference of the wheel in

mm. To obtain Wheel Factor:

1) Fast (and not so accurate) Method — use

chart provided.

2) Most accurate method:

a) See gure 8.

b) Inate your tires to proper pressure

c) Put a mark on the outside circumference

of your front wheel (use masking tape)

d) Put a mark on the oor.

e) Put the mark on the wheel on the mark on

the oor.

f) Rotate the wheel one full revolution until

the mark on the wheel is on the oor

again. Mark this spot on the oor.

g) Measure the distance between the marks

on the oor in mm. This is your wheel

factor (i.e. your wheel circumference).

Fig.8

distance in millimeter

per one turn

Wheel Factor C

1913

1953

2005

2010

2023

2050

2055

2068

2170

2070

2086

2096

2105

2136

2170

2145

2155

2161

2288

2326

Wheel Diameter D

26 x 1.0

26 x 1.25

26 x 1.4

26 x 1.5

26 x 1.75

26 x 1.95

26 x 2.0

26 x 2.1

26 x 2.3

700 x 18

700 x 20

700 x 23

700 x 25

700 x 28

700 x 30

27 x 1"

27 x 1 1/8"

27 x 1 1/4"

29 x 2.1

29 x 2.3

COMPUTER FUnCTiOnS

Clock (12H/24H): A 12 or 24-hour digital clock is displayed on the

third row of the screen. After Km/mile selection in setup mode,

the 12h/24h will ash. Press the RIGHT button to switch between

the 12 and 24-hour format.

Press the LEFT button to conrm and advance to the clock mode.

Press the RIGHT button to advance the hours (hold RIGHT button

for fast advance). Press the LEFT button to conrm hours. Press

the RIGHT button to advance minutes (hold RIGHT button for fast

advance). Press LEFT button to conrm minutes and advance to

“Maintenance Required Function”.

Maintenance Required Function: On the top left hand side a

wrench icon will be displayed, just below the wrench the KM

(or miles — M) will be displayed and the top row digits will be

ashing. The digits represent the distance interval in KM (or miles)

that the wrench icon will start ashing to remind you to perform

maintenance on your bicycle. You can choose a maintenance

reminder for every 200, 400, 600 and 800 KM (or miles). If 600

KM is chosen, the wrench will ash every 600, 1200, 1800 KM (or

miles), etc. Press the LEFT button to stop the wrench ( ) from

ashing. Press LEFT button to conrm maintenance interval and

exit setup mode.

ODOMETER: To set the odometer

(ODO) after battery replacement

and wheel size setting, press RIGHT

button to advance to ODO mode

and then hold LEFT button for 5

seconds until the last digit of the

ODO is ashing. To adjust the value,

press the RIGHT button and then

press the LEFT button to conrm

and select the value. Repeat this

sequence to reach the desired

odometer value.

Andere Handbücher für cocoon 500

Inhaltsverzeichnis

Sprachen:

Andere Bell Fahrradzubehör Handbücher

Bell

Bell Dashboard 100 Bedienungsanleitung

Bell

Bell Dashboard 100 Bedienungsanleitung

Bell

Bell COCOON 300 Series Bedienungsanleitung

Bell

Bell EZFit Bedienungsanleitung

Bell

Bell Dashboard 300 Bedienungsanleitung

Bell

Bell COCOON 300 Bedienungsanleitung

Bell

Bell BICYCLE HELMET Bedienungsanleitung

Bell

Bell SMOOTH SAILER Series Bedienungsanleitung

Bell

Bell WALLABY Bedienungsanleitung

Bell

Bell Dark Flyer Bedienungsanleitung

Bell

Bell FreeFit Bedienungsanleitung

Bell

Bell Platinum series Bedienungsanleitung

Bell

Bell BICYCLE HELMET Bedienungsanleitung

Bell

Bell TotalFit Bedienungsanleitung

Bell

Bell Dashboard 300 Bedienungsanleitung

Bell

Bell iPulse Bedienungsanleitung

Beliebte Fahrradzubehör Handbücher anderer Marken

Sigma

Sigma BC 16.16 Bedienungsanleitung

Playcore

Playcore Dero Setbacks Bedienungsanleitung

VDO Cyclecomputing

VDO Cyclecomputing x3dw Bedienungsanleitung

Cateye

Cateye RAPID X2 Bedienungsanleitung

buratti meccanica

buratti meccanica Clorofilla Trail Bedienungsanleitung

Shimano

Shimano SG-8R20 Betriebsanleitung

BOB

BOB YAK Bedienungsanleitung

APLIC

APLIC 303303/20190717TW012 Bedienungsanleitung

SRAM

SRAM AXS BlipBox Bedienungsanleitung

Garmin

Garmin EDGE 500 Bedienungsanleitung

Shimano

Shimano FD-RX810 Bedienungsanleitung

Cateye

Cateye V2C - Gebrauchsanweisung

KMART

KMART 43115907 Bedienungsanleitung

SIGMA SPORT

SIGMA SPORT Buster 2000 Bedienungsanleitung

NVO Components

NVO Components STEM Bedienungsanleitung

DAXYS

DAXYS BP188 Bedienungsanleitung

XLC

XLC BV-W17 Bedienungsanleitung

Deda Elementi

Deda Elementi SUPERBOX Bedienungsanleitung

Bell cocoon 500 Bedienungsanleitung

Beliebte Fahrradzubehör Handbücher anderer Marken