Bell Dashboard 300 Bedienungsanleitung

dashboard 300

20-FUNCTION CYCLE COMPUTER

table of contents

COMPONENTs.....................................................................................................................3

INsTaLLaTION.....................................................................................................................4

PROgRaMMINg ThE COMPUTER ........................................................................................5

addITIONaL FUNCTION MOdEs..........................................................................................7

TROUbLEshOOTINg ..........................................................................................................12

COMPOsaNTs...................................................................................................................13

INsTaLLaTION...................................................................................................................14

PROgRaMMaTION dE L’ORdINaTEUR ...............................................................................15

FONCTIONs sUPPLÉMENTaIREs.......................................................................................17

dÉPaNNagE......................................................................................................................22

COMPONENTEs.................................................................................................................23

INsTaLaCIÓN ....................................................................................................................24

CÓMO PROgRaMaR EL CICLOCOMPUTadOR....................................................................25

MOdaLIdadEs dE FUNCIÓN adICIONaLEs.......................................................................27

LOCaLIZaCIÓN dE aVERÍas...............................................................................................32

components

WARNING!

· Improper installation of this or any other bike

computer can result in an accident. Read

instructions carefully.

· Call 1-800-456-BELL if you have any questions.

· Check mounting hardware & transmitter installation

before each ride for adjustment and secure t.

· This computer will not t all bikes. If you cannot get a

secure installation per the instruction manual, do not

use this computer.

Computer Battery

(3.0V/CR2032) Cable Ties (4)

Magnet

Computer Unit

Mounting Bracket

installation

STEP 1: Install the Battery– Remove the battery cover from the bottom of the computer using a small coin

(Figure 1). Install the computer battery (3.0V/CR2032) with the positive (+) pole facing up. Replace the battery

cover and tighten. Note: Replacing the battery will erase all stored information. When installing a new battery

after having used the computer, make sure to write down the odometer value before changing the battery so

you can later re-enter it in the computer.

STEP 2: Install the Magnet to the Wheel– Clamp the magnet to a spoke on the right side of the front

wheel (Figure 2). Make sure that the magnet is facing the outside of the wheel so that the at side of the

magnet passes in front of the sensor.

STEP 3: Attach the Sensor to the Fork– Attach the computer sensor to the right fork leg using two of the

cable ties provided. Make sure the metal side of the sensor is facing the wheel. Do not fully secure the cable

ties yet, as the sensor location may require further adjustment (Figure 3). Adjust the sensor and magnet loca-

tion so that clearance between the two is no greater than 2mm. (Figure 4). The magnet should now pass by

the tip of the sensor when the wheel rotates.

STEP 4: Install the Mounting Bracket & Computer– Attach the mounting bracket to the handlebar by

using the remaining 2 cable ties as shown in (Figure 4). Make sure the mounting bracket is clamped tightly

and will not slip on the handlebar. Insert the computer into the mounting bracket (Figure 5). When adjustments

have been made and the computer operates correctly, tighten completely all nuts and bolts.

Sensor

or Magnet

5mm

Sensor

Magnet

Sensor

Top View

Bicycle fork

STEP 1: Set the Wheel Value– First, using

the table provided, determine the correct, 4-digit,

wheel value based on the size of your tire. The

wheel value is the distance in millimeters per one

revolution of the wheel. Next, press and hold the

left and right button for two seconds. The preset

value “2124” should appear with the digit “4”

ashing. Press the right button to modify the digit

to the correct setting. Once correct digit is shown,

press the left button to move to the next digit.

Repeat until all four digits are set to the correct

wheel value for your bike.

STEP 2: Set KM or Mile Selection– After setting the wheel value, the KM/M selection will appear. Press the

RIGHT button to choose kilometer or mile selection. Press the LEFT button to conrm.

STEP 3: Set Age and Weight– After setting the KM/M selection, two numbers will appear. Enter your age

as the large number above the horizontal line. Press the RIGHT button to modify the “ones” digit to the correct

setting. Press the LEFT button to conrm. Repeat for the “tens” digit. Enter your weight as the smaller number

below the horizontal line following the same steps. By entering your actual age and weight, you will get a more

accurate calculation of calories and fat burned NOTE: The computer will default to kilograms (80kg) or pounds

(160lb) based on your selection of kilometers or miles respectively.

Road Bike

20" 1596

22" 1759

24" 1916

26" 2073

27"/700c 2124

28" 2237

Mountain Bike

24" 1888

26" 2045

26x2.25" 2077

27" 2155

29x2.1" 2288

29x2.23 2326

programming the computer

STEP 4: Set Distance for Maintenance Reminder– After setting age and weight, the preset number of 600

km (or miles) will ash. Press the RIGHT button to select 200, 400, 600 or 800 km (or mile) maintenance interval,

then press the LEFT button to conrm. When your odometer (ODO) reaches the selected distance interval, the

wrench icon ( ) will ash, reminding you to service your bicycle (check tires and other parts for wear, lubricate

chain, etc…). Press the LEFT button to stop the wrench icon ( ) from ashing.

STEP 5: Set the Clock– The clock function will appear at the bottom of the screen. Press and hold the LEFT

button for 3 seconds to get a ashing "24H" symbol. Press the RIGHT button to select between 12 and 24 hour

format. Press the LEFT button to conrm. Next, the hour digits will start to ash. Use the RIGHT button to select the

hour and press the LEFT button to conrm. Repeat for minutes digits. Press the LEFT button once more to set the

clock. Press the RIGHT button to enter ODO mode.

STEP 6: Test to Ensure Proper Installation– Now that the computer is programmed, insert it into the

bracket. Spin the front wheel. The speed tendency icon in the upper left corner of the screen should be turning as

the computer starts recording data (Refer to Troubleshooting in case of problems).

additional function modes

ODOMETER (ODO)– Total distance traveled is indicated by “ODO” and displayed

on the bottom line. To reset ODO, press both RIGHT and LEFT buttons for 3 seconds

or remove and replace the battery. Now press the RIGHT button to advance to the

DST mode.

TRIP METER (DST)– Trip distance is indicated by DST and is displayed on the

bottom line. The Trip Meter is activated automatically with speedometer input (comes

on automatically when you begin riding, turns off when you stop). To reset DST to zero,

press and hold the RIGHT and LEFT buttons for 3 seconds. Note that TM (Trip Time)

& AVS (Average Speed) will also be reset at that time. Now press the RIGHT button to

advance to the MXS mode.

MAXIMUM SPEED (MXS)– Maximum speed is indicated by MXS and is displayed

on the bottom line. Maximum speed is stored in memory and updates only when a

higher speed is reached. To reset MXS, press and hold the LEFT button for 3 seconds.

Now press RIGHT button to advance to Average Speed (AVS) mode.

additional function modes

AVERAGE SPEED (AVS)– Average speed is indicated by AVS and is displayed on

the bottom line. AVS works in conjunction with the Trip Timer (TM) to calculate the

average speed for a specic trip. Now press the RIGHT button to advance to the Trip

Timer (TM) mode.

TRIP TIMER (TM)– Trip Timer is indicated by TM and is displayed on the bottom

line. The Trip Timer is activated automatically with computer input (comes on

automatically when you begin riding, turns off when you stop). It records only the time

actually spent riding. To reset TM to zero, return to DST (Trip Meter) mode and reset

to zero per the instructions above. Return to TM mode and press RIGHT button to

advance to TEMPERATURE (TEMP) mode.

TEMPERATURE (TEMP)– Your computer has a thermometer to measure outdoor

temperature. To select between Celsius (C) and Fahrenheit (F) readout, press and

hold the LEFT button for 3 seconds until you see a ashing "F". Press LEFT button

to conrm Fahrenheit (F) readout. If you prefer Celsius readout, press RIGHT button

to switch to Celsius (C) and then press LEFT button to conrm. Now press the RIGHT

button to advance to Calorie (CAL) mode

additional function modes

CALORIES BURNED (CAL)– This function estimates the number of calories burned

while riding, based on the age and weight inputed by the user. To reset CAL, press

and hold the LEFT button for 2 seconds. Now press the RIGHT button to advance to Fat

Burned (FAT) mode.

FAT BURNED (FAT)– This function estimates the number of fat grams burned while

riding, based on the age and weight inputed by the user. To reset FAT, press and

hold the LEFT button for 2 seconds. Now press RIGHT button to advance to the SCAN

(SCAN) mode.

SCAN– The Scan mode conveniently rotates DST, MXS, AVS, and TM readings on the

computer screen without the need to press any buttons. Now press the RIGHT button

to return to the Clock mode.

additional function modes

FREEZE FRAME MEMORY– Press the LEFT button, Freeze Frame Memory can lock

the display at the end of a ride segment and information TM, DST and AVS which will

be ashing, can be read at a later time by the RIGHT key. To release the memory, press

the LEFT key until the display digit is static again. This is particularly useful when

crossing the nish line of a time trial, since the TM cannot be stopped manually.

ODOMETER SAVE FUNCTION– The SAVE function allows you to keep the impor-

tant data of total distance (ODO) even after battery replacement. To set ODO, after

battery replacement and wheel size setting, press RIGHT button to ODO mode and

then hold LEFT button for 2 seconds until the last digit ickering. To adjust number,

press the RIGHT button and then press the LEFT button to conrm and select digit to

be input. Repeat this sequence to reach the desired odometer value. Press the LEFT

button again to return to normal ODO mode.

AUTO STOP/START– To preserve batteries, the cycle computer will automatically

switch off if the unit is left unused for over 5 to 6 minutes. Display will reappear with a

press on either button or input from the sensor.

Andere Handbücher für Dashboard 300

Inhaltsverzeichnis

Sprachen:

Andere Bell Fahrradzubehör Handbücher

Bell

Bell SMOOTH SAILER Series Bedienungsanleitung

Bell

Bell BICYCLE HELMET Bedienungsanleitung

Bell

Bell Dark Flyer Bedienungsanleitung

Bell

Bell FreeFit Bedienungsanleitung

Bell

Bell iPulse Bedienungsanleitung

Bell

Bell Dashboard 300 Bedienungsanleitung

Bell

Bell Dashboard 100 Bedienungsanleitung

Bell

Bell cocoon 500 Bedienungsanleitung

Bell

Bell TotalFit Bedienungsanleitung

Bell

Bell Dashboard 100 Bedienungsanleitung

Bell

Bell Platinum series Bedienungsanleitung

Bell

Bell COCOON 300 Bedienungsanleitung

Bell

Bell WALLABY Bedienungsanleitung

Bell

Bell BICYCLE HELMET Bedienungsanleitung

Bell

Bell EZFit Bedienungsanleitung

Bell

Bell COCOON 300 Series Bedienungsanleitung

Beliebte Fahrradzubehör Handbücher anderer Marken

Sigma

Sigma BC 16.16 Bedienungsanleitung

Playcore

Playcore Dero Setbacks Bedienungsanleitung

VDO Cyclecomputing

VDO Cyclecomputing x3dw Bedienungsanleitung

Cateye

Cateye RAPID X2 Bedienungsanleitung

buratti meccanica

buratti meccanica Clorofilla Trail Bedienungsanleitung

Shimano

Shimano SG-8R20 Betriebsanleitung

BOB

BOB YAK Bedienungsanleitung

APLIC

APLIC 303303/20190717TW012 Bedienungsanleitung

SRAM

SRAM AXS BlipBox Bedienungsanleitung

Garmin

Garmin EDGE 500 Bedienungsanleitung

Shimano

Shimano FD-RX810 Bedienungsanleitung

Cateye

Cateye V2C - Gebrauchsanweisung

KMART

KMART 43115907 Bedienungsanleitung

SIGMA SPORT

SIGMA SPORT Buster 2000 Bedienungsanleitung

NVO Components

NVO Components STEM Bedienungsanleitung

DAXYS

DAXYS BP188 Bedienungsanleitung

XLC

XLC BV-W17 Bedienungsanleitung

Deda Elementi

Deda Elementi SUPERBOX Bedienungsanleitung