Bellfires BEL VBMT-3NG-SB Bedienungsanleitung

Vertical Bell Medium Tunnel 3 LF

Direct Vent Gas Fireplace

Installation manual

This appliance may be installed in an aftermarket, permanently located home

or mobile home, where not prohibited by local codes. This appliance is only

for use with the types of gas indicated on the rating plate. A conversion kit is

supplied with the appliance.

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and

shall be installed for the protection of children and other

at-risk individuals.

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

- Do not store or use gasoline or other ﬂammable vapors and liquids in

the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Leave the building immediately.

• Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre department.

- Installation and service must be performed by a qualiﬁed installer,

service agency or the gas supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury,

death or property damage.

INSTALLER:

Leave this manual with

the appliance.

CONSUMER:

Retain this manual for

future reference.

Bellﬁres Installation instructions

CONTENTS

Vertical Bell Medium Tunnel 3 LF :

All warnings and instructions apply to both doors (front glass frames)

and both barriers !

Page

IMPORTANT SAFETY INSTRUCTIONS ................................................

.......

... 5

CODE APPROVAL .....................................................

.......

.........

...

....

...

. 8

PRE INSTALLATION INSTRUCTIONS ............................

...............

...........

.....

. 9

GENERAL ................................................................

......

....

.....

......

... 9

CONCENTRIC FLUE SYSTEMS ...............................

.........

....

..........

. 10

INCLUDED WITH THE APPLIANCE ..........................

......................

........ 10

OPTIONS AND ACCESSORIES .............................................................. 1

CLEARANCES .................................................................

...

.....................

.. 12

VENT INSTALLATION ......................................................

.......

......

...

........ 27

POSITIONING THE APPLIANCE ...................................................

.......

........... 43

GAS LINE INSTALLATION ...........................................................

...

....

..........

... 48

BUILDING IN THE APPLIANCE .........................................................

......

........ 53

PLACING OF CERAMIC LOG SET .................................

.........

....

............

.......

. 54

GAS FIRE DECORATION KITS .......................................

....................

............. 58

MOUNTING OF FLUE GAS RESTRICTION PLATE ...........................

........

..... 62

ANNUAL MAINTENANCE ....................................................

..........

...

............

... 64

FAULTS .............................................................................

...........................

..... 65

POSSIBLE REASONS ...................................................

.......

........

......... 65

SAFETY MEASURES IN THE APPLIANCE ............

..............

......

....

........

. 65

DISMANTLING / ASSEMBLING OF THE GLASS .............

.......

......

.........

......... 66

DIAGRAM ELECTRICITY AND GAS ................................................................ 69

DIMENSIONS ...........................................................................

....................

.... 70

OPERATING UNIT .........................................................

.............

.....

....

.......

.....

. 71

TECHNICAL DETAILS ..................................................

...................................

. 72

REPLACEMENT PART LIST ..........

.........................

...........

................

........

......

. 73

PROPANE CONVERSION KIT ...........................................................

....

WARRANTY TERMS ......................................................

....

...

........

.........

......... 77

Bellﬁres Installation instructions

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Improper installation, adjustment, alteration,

services or maintenance can cause serious injury or property damage.

Refer to this manual.

SAVE THESE INSTRUCTIONS

Make yourself fully aware of all the following instructions and the many

features of the Bell!res direct vent gas !replace appliance.

INSTALLER: Leave this manual with the appliance

CONSUMER: Retain this manual for future reference.

1. This appliance reaches high temperatures. Keep children and adults away from

hot surfaces to avoid burns or clothing ignition. The appliance will remain hot for

a time after shutdown. Allow surfaces to cool before touching.

2. A barrier designed to reduce the risk of burns from the hot viewing glass is

provided with this appliance and shall be installed for the protection of

children and other at-risk individuals.

3. If the barrier becomes damaged, the barrier shall be replaced with the

manufacturer’s barrier for this appliance.

4. Any safety screen, guard or barrier removed for servicing the appliance, must

be replaced prior to operating the appliance.

5. Children and adults should be alerted to the hazards of high surface

temperature and should stay away to avoid burns or clothing ignition.

6. Young children MUST be carefully supervised when they are in the same room

as the appliance. Toddlers, young children and others may be susceptible to

accidental contact burns. The remote control handset should be kept out of

reach of children. A physical barrier is recommended if there are at risk

individuals in the house. To restrict access to a ﬁreplace or stove, install an

adjustable safety gate to keep toddlers, young children and other at risk

individuals out of the room and away from hot surfaces.

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and

shall be installed for the protection of children and other

at-risk individuals.

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

Bellﬁres Installation instructions

IMPORTANT SAFETY INSTRUCTIONS

WARNING: The conversion kit shall be installed by a quali!ed

service agency in accordance with the manufacturer’s instructions and

all applicable codes and requirements of the authority having jurisdiction.

If the information in these instructions is not followed exactly, a !re,

explosion or production of carbon monoxide may result causing property

damage, personal injury or loss of life. The quali!ed service agency is

responsible for the proper installation of this kit. The installation is not

proper and complete until the operation of the converted appliance, is

checked as speci!ed in the manufacturer’s instruction supplied with

this kit.

13. This appliance must not be connected to a chimney !ue serving a separate

solid-fuel burning appliance.

14. Installation and service must be performed by a quali"ed installer, service agency

or gas supplier.

15. DO NOT operate the appliance with glass removed, cracked or broken.

16. DO NOT use abrasive cleaners on the panels. DO NOT attempt to clean the

glass when it is hot.

17. DO NOT strike or slam the glass panel.

18. DO NOT modify the appliance under any circumstances. Any parts removed for

servicing must be replaced prior to operating the appliance.

19. Turn the appliance off and let cool before servicing, installing or repairing.

ONLY a quali"ed service person should install, service or repair the appliance.

Have burner system inspected annually by a quali"ed service person.

7. Keep the area around your appliance clear of combustible materials, gasoline

and other !ammable vapor and liquids.

8. Do not place embers, vermiculite granules or wood logs against the pilot light

burner. Make sure that the pilot !ame can burn at all times freely over the

main burner. Only in this way is proper ignition of the main burner ensured.

Ignoring these directions could lead to a dangerous situation.

9. Never place anything on top of the appliance.

10. Do not use this appliance to cook food or burn paper or other objects.

11. Do not use any solid or liquid fuels in this appliance. Use only the gas type

indicated on the rating plate.

12. This appliance is only for use with the type of gas indicated on the rating plate.

This appliance is convertible for use with other gases. A conversion kit is supplied

with this appliance.

Bellﬁres Installation instructions

IMPORTANT SAFETY INSTRUCTIONS

20. Keep control compartments, burners and circulating air passages clean. More

frequent cleaning may be needed due to excessive lint and dust. Turn off the

gas valve and appliance (OFF on remote control) before cleaning the appliance.

21. The venting system MUST checked annually by a qualiﬁed service person.

If needed, have the venting system cleaned or repaired.

22. When the appliance is installed directly on carpeting, tile or other combustible

material, it must be set on a metal panel or hearth pad extending at least the full

width and depth of the appliance.

23. DO NOT obstruct the ﬂow of combustion and ventilation air in any way. Provide

adequate clearances around air openings into the combustion chamber along

with adequate accessibility clearance for servicing and proper operation.

24. DO NOT use the appliance if any part has been exposed to or has been under

water. Immediately call a qualiﬁed service technician to inspect the appliance and

replace any part of the control system and any gas control which has been

submerged in water.

25. DO NOT operate the appliance if any log is broken.

26. The installation must conform with local codes or, in the absence of local codes,

with the Natural Gas and Propane Installation Code, CSA B149.1.

27. This appliance, when installed, must be electrically grounded in accordance with

local codes or in the absence of local codes, with the Canadian Electrical Code,

CSA C22.1.

28. The appliance is equipped with a safety system, whereby the door (front glass

frame) will extract any over-pressure in a controlled way. In this, the door will

brieﬂy open. A safety strip limits the maximum degree to which the door can be

tilted. To avoid any possible personal harm when the door opens due to an

over-pressure, always maintain a minimum distance of 40 in (100 cm) to the

appliance, when igniting and when burning. If an over-pressure situation occurs,

the appliance should be thorougly checked by the installer.

WARNING: Never connect unit to private (non-utility) gas wells.

This gas is commonly known as well-headed gas.

IMPORTANT:

Take care that no pipes get damaged and no compression !ttings come

loose when moving the gas regulator block. Prevent twisting the "exible

pipes# Check all compression !ttings for leaks afterwards#

Bellﬁres Installation instructions

CODE APPROVAL

Direct Vent type appliances draw all combustion air from outside of the dwelling through

the vent pipe.

These appliances have been tested by CSA and found to comply with the established

standards for VENTED GAS FIREPLACES in Canada as follows:

LISTED VENTED GAS FIREPLACES

Vertical Bell Medium Tunnel 3 LF tested to:

- ANSI Z21.88-2014 / CSA 2.33-2014 Vented Gas Fired Heaters.

- CSA P4.1 - 09 Testing method for measuring annual ﬁreplace efﬁciency.

A mobile home OEM installation must conform with the Standard for Gas Equipped

Recreational Vehicles and Mobile Housing, CSA Z240.4.

IMPORTANT SAFETY INSTRUCTIONS

Bellﬁres Installation instructions

PRE INSTALLATION INSTRUCTIONS

GENERAL

This ‘direct vent’ gas appliance must be installed by a qualiﬁed installer in accordance

with local building codes, or in the absence of local codes, with the current CAN/CSA-

B149.1 or .2 Installation Code

This appliance, when installed, must be electrically connected and grounded in accor-

dance with local codes, or in the absence of local codes, with the current CSA C22.1

Canadian Electrical Code. If you have any queries regarding the installation, please

consult your local gas company.

The appliance is supplied with a “Line Fire” double burner. This burner has a speciﬁc

ﬂame image which is deﬁned by the perforation pattern in the burner cover.

See Chapter “DIAGRAM ELECTRICITY AND GAS” and the Operating Manual.

The appliance is factory set to the correct nominal heat input. The pilot light is set to the

correct level of consumption.

The appliance will be delivered from the factory with a 5⅛" x 7⅞" concentric connection

for extracting the ﬂue gases and supply of combustion air.

It is possible to install the appliance with either a wall or roof outlet. The roof connection

must be carried out using a Bellﬁres adapter (5⅛" x 7⅞" to 5" x 8") together with a

reducer (5" x 8" to 4" x 6⅝") or using a Bellﬁres adapter (5⅛" x 7⅞" to 4" x 6⅝"), and

the concentric ﬂue system 4" x 6⅝". The fumes are exhausted naturally to the outside

environment through the inner 4" pipe whereas the combustion air supply passes

between the 4" and 6⅝" pipes.

The wall connection must be carried out using a Bellﬁres adapter (5⅛" x 7⅞" to 5" x 8")

and the concentric ﬂue system 5" x 8". The ﬂue gases are evacuated outside by means

of natural draft through the internal pipe of 5", whereas the combustion air is supplied

between the pipes of 5" and 8".

The appliance can be installed in a completely sealed or mechanically ventilated house

without extra ventilation and/or fume extraction.

IMPORTANT:

Before beginning the installation, check that the details on the rating

plate correspond to the gas type and pressure to which the appliance

will be connected.

WARNING: Due to high temperatures, the appliance should be

located out of traf!c and away from furniture and draperies.

IMPORTANT: This appliance is solely intended for installation

and use in Canada.

Bellﬁres Installation instructions

N.B. If any part is missing, please contact your dealer.

INCLUDED WITH THE APPLIANCE

Set documentation - Instructions for use

- Installation instructions

Attributes - Barrier

- Ceramic log set

- Hook (for opening the frame and the glass)

- Propane conversion kit Vertical Bell Medium Tunnel 3 LF

PRE INSTALLATION INSTRUCTIONS

The appliance can be installed as an insert into an existing open ﬁre place or as a built-

in appliance in a new ﬁre place. In order to prevent the ﬁreplace heating up excessively,

it must be properly ventilated by installing vents at the top of the ﬁreplace.

The provided barrier safety screen designed to reduce the risk of burns from the hot

viewing glass shall be installed.

If an existing chimney is to be used, please consult your installer ﬁrst. If the chimney

was previously used for a wood or coal ﬁre, then it should be cleaned by an expert.

CONCENTRIC FLUE SYSTEMS

• M&G DuraVent - Direct Vent Pro ..................................... 4” x 6⅝” and 5” x 8”

• SELKIRK - DIRECT-TEMP - Direct Vent Products

........

. 4” x 6⅝” and 5” x 8”

• METAL-FAB - Sure-Seal - Direct Vent Products

...........

. 4” x 6.5” and 5” x 8”

The appliance, in combination with the concentric ﬂue system [4” x 6⅝”] and/or [5” x 8”]

(rigid and/or ﬂexible) for the brands, M&G DuraVent (Direct Vent Pro), Selkirk (Direct

Temp) or Metal-Fab (Sure-Seal) has been approved in accordance with the ANSI / CSA

standard for direct vented gas appliances and may therefore be used only with these

systems.

The permitted components for these systems are listed in Chapter “Vent Installation”.

The guarantee on the appliance lapses if it is installed, fully or partially, with other

components or a different ﬂue system.

The concentric ﬂue [4” x 6⅝”] and [5” x 8”] systems can be used with either a newly-built

or existing chimney.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bellfires Kamin im Innenbereich Handbücher

Bellfires

Bellfires Smart Bell 65 MF Betriebsanleitung

Bellfires

Bellfires VIEW BELL SMALL 3 CF/LF Leitfaden

Bellfires

Bellfires horizon bell xl 3 cf Bedienungsanleitung

Bellfires

Bellfires DERBY LARGE 3 PF Gebrauchsanweisung

Bellfires

Bellfires VIEW BELL YORK 3 CF Leitfaden

Bellfires

Bellfires HBXXL3 CF Bedienungsanleitung

Bellfires

Bellfires CLASSIC BELL MEDIUM 3 PF Installations- und Betriebshandbuch

Bellfires

Bellfires Smart Bell 75/55 MF Bedienungsanleitung

Bellfires

Bellfires BM 21 Bedienungsanleitung

Bellfires

Bellfires VIEW BELL XXL 3 CF Leitfaden

Bellfires

Bellfires VERTICAL BELL SMALL 3 CF Installations- und Betriebshandbuch

Bellfires

Bellfires Smart Bell Panorama 45/45 MF Betriebsanleitung

Bellfires

Bellfires SB 75 PF Installations- und Betriebshandbuch

Bellfires

Bellfires Tunnel 3 Installations- und Betriebshandbuch

Bellfires

Bellfires SMART BELL 80 Leitfaden

Bellfires

Bellfires UNICA 200 L Technisches Handbuch

Bellfires

Bellfires Derby Large Tunnel 3 CF Bedienungsanleitung

Bellfires

Bellfires BSV 19 Bedienungsanleitung

Bellfires

Bellfires Smart Bell 80 MF Betriebsanleitung

Bellfires

Bellfires UNC-2 40 Leitfaden

Bellfires

Bellfires SLIDE BELL Einrichtungshandbuch

Bellfires

Bellfires UNICA-2 40 Bedienungsanleitung

Bellfires

Bellfires SMART BELL 80-70 PF Installations- und Betriebshandbuch

Bellfires

Bellfires Smart Bell 65/55 MF Betriebsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch