BG Electrical NX13ADC/IL/A Bedienungsanleitung

Accessories

Socket/Chime

1. x2 Fixing Screws

Push Button

1. x2 Fixing Screws

2. x2 Rawl Plugs

3. Double Sided Sticky Pad

4. Push Button Battery (3V CR2032)

Wiring Instructions

1. Power Off

2a. Replacing an existing accessory

2b. New installation

Before commencing work always isolate the power at the consumer unit

/ fuse box.

*Note – If your installation uses a four-lug metal mounting box, remove the

top and bottom lugs or bend fully back.

1. Unscrew the accessory from the wall/mounting box.

2. Note the cable connections:

The illustration shows 1 wire of each colour connected to each terminal.

There should be an additional connection between the mounting box earth

terminal and the accessory earth terminal.

3. Unscrew each terminal to release the wire.

1. Install mounting box (metal or moulded) for either ﬂush or surface

mounting, ensuring appropriate size of product.

2. Select the most suitable entry point of the mounting box (knock-out) and

route the cables through.

If a metal box is used, a cable grommet should be ﬁtted to the entry point.

3. Cables should be prepared so a sufﬁcient conductor length reaches the

terminals.

Strip the ends of the individual conductors leaving an adequate length bare

to enter terminals.

3. Connection (See diagram)

1. Line up the new accessory to mounting box and take note of where each

terminal is located.

2. Connect each wire to the matching terminal.

An earth connection should always be made between the mounting box

earth terminal and the accessory earth terminal, where ﬁtted.

All bare earth wires must be sheathed with green/yellow sleeving.

When connecting the new accessory ensure that only the bare end of the

wire enters the terminal and no bare wires are visible.

3. Tighten terminal screws securely. (Do not over tighten)

4. This socket is ﬁtted with two linked terminals to provide a dual earth fa-

cility. This is for use in “clean” installations where additional earth capacity

is required to comply with Regulation 607 IEE Wiring Regulations.

4. Complete Installation & Test

1. Carefully position the accessory into the mounting box, ensuring that no

wires are trapped between the plate and the wall and secure with screws

(do not over tighten) then insert screw covers (optional).

2. Once the installation has been completed correctly, replace the fuse/

reset MCB (trip), switch the power back on at the consumer unit and test.

Wiring Accessories

13A Socket with Door Chime

NX13ADC/IL/A Safety Warning

3. Offer the push button backing up to the wall and drill holes. If ﬁtting to

masonry, use a 6mm drill bit, as per the depressions and securing by

using the supplied rawl plugs and screws. If ﬁtting directly to the

woodwork, use a 2mm drill bit and screw directly into frame or use the

provided sticky pad.

4. Pull plastic tab from under battery to power the push button.

Installation

1. First, identify a suitable area for the push button to be positioned.

Ideally, this should be sheltered from rain or excess heat.

It would be recommended that the button is ﬁtted to the door frame itself,

so you are able to screw directly into the woodwork, making the

installation simple.

2. Place a small ﬂathead screwdriver into the slotted hole and gently

twist to remove push button back.

FUNCTIONAL EARTH

NEUTRAL

EARTH

LIVE

NEUTRAL

EARTH

LIVE

TO MOUNTING BOX

EARTH TERMINAL

For your safety, this product must be installed in accordance with local

Building Regulations.If in any doubt, or where required by the law, con-

sult a competent person who is registered with an electrical self-certiﬁ-

cation scheme. Further information is available online or from your Local

Authority.

Please read carefully and use in accordance with these safety wiring

instructions. Before commencing any electrical work ensure the supply is

switched off at the mains. Either by switching off the consumer unit or by

removing the appropriate fuse or turning off MCB (trip). Wiring should be in

accordance with the latest edition of the IET regulations (BS 7671).

To prevent ﬁre hazard always use cable of the correct rating & type for the

application.

Warning do not exceed the load rating of this device as stated on the rear

of the product.

Wire Identiﬁcation – Twin & Earth Cable

Note - As from 1st April 2004 new colour codes for hard wire installations

were introduced.

EARTH = Green/Yellow Sleeving

NEUTRAL = Black (pre Apr 04) / Blue (after Apr 04)

LIVE = Red (pre Apr 04) / Brown (after Apr 04)

5. Reﬁt the push button to the secured backing by offering up the button of

the push button and gently pushing back together.

ﬁt ﬁrst

press down

Batch Code explanation

yyWxx Manufacturing date code, year of manufacture (yy) and week of

manufacture (Wxx)

Environmental Protection

This symbol is known as the “Crossed-out Wheelie Bin

Symbol”. When this symbol is marked on a product or battery,

it means that it should not be disposed of with your general

household waste. Some chemicals contained within electrical/

electronic products or batteries can be harmful to health

and the environment. Only dispose of electrical/electronic/

battery items in separate collection schemes, which cater for

the recovery and recycling of materials contained within. Your

co-operation is vital to ensure the success of these schemes

and for the protection of the environment.

Address/Helpline

If you have further technical assistance you can get in touch with our

Technical Helpline on:

+44 (0)3300 249 279

technical.support@bgelectrical.co.uk

(EU) Luceco SE

C/ Bobinadora 1-5

08302 Mataró

SPAIN

Luceco PLC

Stafford Park 1

Telford TF3 3BD

ENGLAND

Setup Door Chime EU Declaration of Conformity

Indoor use only

Door Chime Socket only

This product does not consist of any serviceable parts and should not be

repaired. The device should not be operated by persons who have a lack of

experience or knowledge in using such products. People who have a

reduced physical, sensory or mental capability should be supervised or

given instruction when operating. Children should be supervised, so that

they do not play with the device.

IMPORTANT

Technical Information

Push Button Battery : 1 x 3V CR2032

Push Button : IP44

Melody Count : 6

Sound Level : 80dB

Range : 100M (open air)

Wall Box Depth : 25mm

•

Unique Code Selection

The door chime and push button will be paired straight out of the box, with 1 out

of 1 million unique codes to prevent interference with another door chime. If

the door chime does not sound, please refer to the 'Pairing Additional Push

Buttons & Door Chimes' section.

Chime Selection

Volume Selection

Pairing Additional Push Buttons & Door Chimes

Reset Door Chime

Maximum distance is based on an open area environment. Any walls,

doors or ceilings may reduce the operating range.

Door chime is to be used indoors only.

Door Chime Not Working?

Single press the melody button on the left of the door chime socket to

ﬁlter through the six different options – 4 x ‘Ding-dong’ and 2 x ‘Westminster’

chimes.

1. Single press the right side volume selection button to ﬁlter through the

four different volumes settings. Options include – No sound, low, mid

and high volume.

2. The LED ﬂasher will always ﬂash for 10 seconds on each press of the button.

Press and hold the Melody button until the LED illuminates, then release.

Push the button on the ‘Push Button’, once the door chime socket will ring,

then the units are paired. Repeat the process to pair additional push buttons

to the door chime.

(A maximum of 16 push buttons can be paired).

Press and hold the melody button for 10 seconds or until you hear a triple

‘beep’ to reset the door chime.

1. Ensure the battery in the push button is new..

2. Objects and materials, such as walls, doors, ceilings and furniture, are

blocking the signal. Try moving the chime closer to the push button.

3. Wireless interference can be caused by external wireless devices, such

as alarms and adaptors. It is recommend not to plug-in such devices in the

door chime socket, or have in the close vicinity.

4. Door chime and push button are not paired – please refer to the ‘Pairing

Additional Push Buttons’ section.

5. Ensure wired connections are made good, MCB is on and power is being

made to the socket.

Chime Selection

Volume Selection

EU Declaration of Conformity

Applicant: Luceco PLC

Address: Luceco Distribution Centre, Stafford Park 1, Telford Shropshire,

United Kingdom

(EU) Luceco SEC/Bobinadora 1-5 08302 Mataró SPAIN

Description: 13A Socket with Door Chime

Model: 822BELL

We (Luceco PLC) declare under our sole responsibility that the products

above are in conformity with the essential requirements of the following:

Signed for and on behalf of: David Cleaver

Senior Product Manager

Place of Issue: Stafford Park 1,Telford Shropshire, United Kingdom

Date of Issue: 16/Mar/2020

This product belongs to receiver category 2

: Caution

Push Button

This product contains a coin/button cell battery and if ingested can cause

severe chemical burns. If the battery has been ingested, please seek

medical advice immediately. In just 2 hours a digested battery can lead

to death. Keep new and used batteries away from children. If the battery

compartment does not close securely, please stop using the product.

Radio Equipment Directive (RED)

2014/53/EU

Article 3.1(a)Health

EN62479:2010

EU Directives Conformas to

2011/65/EU and its amendment

2015/863/EU(ROHS)

ROHS 2011/65/EU and its amendment

2015/863/EU

2009/125/EC ERP ERP:

EN 50564:2011

Article 3.2 Radio:

EN 300 220-1 V3.1.1 (2017-02)

EN 300 220 2 V3.1.1 (2017-02)

Article 3.1(b)EMC:

Draft EN 301 489-1 V2.2.0 (2017-03)

EN 301 489-3 V2.1.1 (2019-03)

Article 3.1(a)Safety:

EN62368-1:2014+A11:2017

Andere BG Electrical Zubehör Handbücher

BG Electrical

BG Electrical Smart! Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung