BGS technic 3268 Bedienungsanleitung

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

Art. 3268

Air Separation Tool

Safety rules

1. Always wear approved eye protection.

2. Have throttle (trigger) in "OFF" position when connecting to air supply.

3. Disconnect tool before performing service or when not in use.

4. Always use tool in a safe distance from other people in work area.

5. Maintain tools with care. Keep tools clean and oiled for best and safest performance. Follow

instructions for lubricating and changing accessories. Wiping or cleaning rags and other

flammable waste materials must be placed in a lightly closed metal container and disposed of later

in the proper fashion.

6. Do not wear loose or ill-fitting clothing, remove matches and rings.

7. Never use quick change couplings at tool. They add weight and could fail due to vibration. Instead

add a hose whip and connect coupling between air supply and hose whip or between hose whip

and leader hose.

8. Don't overreach, keep proper footing and balance at all times.

9. Don't force tool. It will do the job better and safer at the rate for which it was designed.

10. Don't abuse hoses or connectors. Never carry tool by the hose or yank it to disconnect from power

supply. Keep hoses from heat oil and sharp edges. Check hoses for weak or worn condition

before each use making certain that all connections are secure.

11. When possible secure work with clamps or vise so both hands are free to operate tool.

12. Accessory retainers should be used to prevent discard or ejection of the accessory which might

injure persons in the general area. Switch of tool when changing location or on transport. Never

carry the tool when trigger is depressed or when cutting wheel is still moving. Accessory should be

removed when tool is not in use.

SPECIFICATION

Disc Size: Ø 100 mm, Bore: Ø 16 mm

Max. Speed: 15,000 rpm

Max. Pressure: 90 psi (6.2 bar)

Air Inlet: 1/4"

Recommended Hose: Ø 10 mm

Length: 376 mm

Weight: approx. 1.4 kg

Noise: LpA = 85 dB(A)

LwA = 88 dB(A)

Vibration: K = 0.6 m/s²

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

Air supply

Tools of this class operate on a wide range of air pressure. It is recommended, that air pressure to

these tools do not exceed 90 PSI / 6,3 bar at the tool while running. Higher pressure and unclean air

will shorten the tool-life because of faster wear and could create an unsafe condition. Water in the air

line will cause damage to the tool. Drain the air tank daily. Clan the air inlet filler screen on at least a

weekly schedule. The recommended hook-up procedure can be viewed in Figure 1. The air inlet (B)

Figure 2. used for connecting air supply has standard 1/4" NPT Thread. Line pressure or hose inside

diameter should be increased to compensate for unusually long air hoses (over 7,5m). Minimum hose

diameter should be 1/4" i.D. but 3/8" i.D. is recommended.

Operating

On tools with regulators the air regulator (B) Figure 2. can be used as an air throttle if there are no

other means of regulating air. Turn the air regulator (B) all the way in and adjust outward until desired

speed. Daily before using and before putting tool into operation, disconnect air hose and pour about

one teaspoonful of recommended oil (see lubrication and Maintenance) into tool air inlet. Blow out air

line to clear it of accumulated dirt and moisture, connect tool and operate on low throttle to allow oil to

be carried to the interior of tool. Let the tool do the work. Do not put extreme pressure on the

machine. This will only slow down the speed of the cutting wheel, reduce cutting efficiency and put

additional burden on the motor. Start the tool off the work. Set it down on the work evenly and move in

the direction desired to make the cut. When finished cutting, lift off the work before stopping the

motor.

NOTE: During operation safety goggles should always be worn to guard against flying rust and chips.

Use only wheels rated at 15.000 rpm or higher.

Fig. 2

AAir Inlet

B Air Regulator

Fig. 2

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

CHANGING CUTTING DISC

CAUTION: Disconnected air tool from air supply before replacing

the cutting disc or other maintenance work.

Note: The internal hexagon screw (Fig. 4.2) is equipped with a left-hand thread.

1. Press and hold the shaft lock (Fig. 3.1).

2. Turn the cutting disc by hand until the shaft lock engages (Abb. 3.1).

3. Loosen and remove the retaining screw by turning clockwise (Fig. 4.2) using a internal hexagon

L-type key.

4. Loosen the shaft nut (Fig. 4.3) by turning it counter-clockwise with the open-end spanner.

Remove the shaft nut and the washer.

5. Replace old cutting disc with new one. Caution: Observe the information on the cutting disc.

6. Placing the washer, tighten the shaft nut and secure it with the internal hexagon screw (Fig. 4.2)

by turning counter-clockwise.

LUBRICATION AND MAINTENANCE

Lubricate the cutting tool motor daily with a high-quality compressed air tool oil, fill a few drops of the

oil into the compressed air inlet (Fig. 2.A).

Start the tool at a low speed so that the oil can be distributed inside the tool.

Fig

. 4

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

CE-Erklärung

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

EU-Konformitätserklärung

EC DECLARATION OF CONFORMITY

DÉCLARATION „CE“ DE CONFORMITE

DECLARATION DE CONFORMIDAD UE

Wir erklären in alleiniger Verantwortung, dass die Bauart der:

We declare that the following designated product:

Nous déclarons sous propre responsabilité que ce produit:

Declaramos bajo nuestra sola responsabilidad que este producto:

Druckluft-Trennwerkzeug ( BGS Art. 3268 )

Pneumatic extended reversible air cutter

Meuleuse d’angle pneumatique

Amoladora angular neumática

folgenden einschlägigen Bestimmungen entspricht:

complies with the requirements of the:

est en conformité avec les réglementations ci-dessous:

esta conforme a las normas:

Machinery Directive 2006/42/EC

Angewandte Normen:

Identification of regulations/standards:

Norme appliquée:

Normas aplicadas:

EN 792-7:2001+A1:2008

EN 28662-1:1993

EN ISO 15744:2008

MSD/LDB-254

Test Report: 2010/11/29

Wermelskirchen, den 20.06.2014

ppa.

Frank Schottke, Prokurist

BGS technic KG, Bandwirkerstrasse 3, D-42929 Wermelskirchen

Andere Handbücher für 3268

Inhaltsverzeichnis

Andere BGS technic Werkzeuge Handbücher

BGS technic

BGS technic 70069 Bedienungsanleitung

BGS technic

BGS technic 69506 Bedienungsanleitung

BGS technic

BGS technic 3327 Bedienungsanleitung

BGS technic

BGS technic 5266 Bedienungsanleitung

BGS technic

BGS technic 8848 Bedienungsanleitung

BGS technic

BGS technic BGS 3064 Bedienungsanleitung

BGS technic

BGS technic 9414 Bedienungsanleitung

BGS technic

BGS technic 74291 Bedienungsanleitung

BGS technic

BGS technic 8283 Bedienungsanleitung

BGS technic

BGS technic BGS 1709 Bedienungsanleitung

BGS technic

BGS technic 6250 Bedienungsanleitung

BGS technic

BGS technic 8978 Bedienungsanleitung

BGS technic

BGS technic 3391 Bedienungsanleitung

BGS technic

BGS technic 6755 Bedienungsanleitung

BGS technic

BGS technic 62636 Bedienungsanleitung

BGS technic

BGS technic 3140 Bedienungsanleitung

BGS technic

BGS technic 8262 Bedienungsanleitung

BGS technic

BGS technic 70943 Bedienungsanleitung

BGS technic

BGS technic 8522 Bedienungsanleitung

BGS technic

BGS technic 8776 Bedienungsanleitung

BGS technic

BGS technic 62666 Bedienungsanleitung

BGS technic

BGS technic 9323 Bedienungsanleitung

BGS technic

BGS technic BGS 70009 Bedienungsanleitung

BGS technic

BGS technic 8778 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung