Billion BiPAC 7300 Bedienungsanleitung
BiPAC 7300(G)
(802.11g) ADSL2+ Router
Quick Start Guide
Billion BiPAC 7300(G) ADSL2+ Router
For more detailed instructions on configuring and using
the (802.11g) ADSL2+ Router, please refer to the on-line
manual.
Package Contents
BiPAC 7300(G) ADSL2+ Router
CD-ROM containing the on-line manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
AC-DC power adapter (12VDC, 1A)
This Quick Start Guide
Warning
Do not use the router in high humidity or high temperatures.
Do not use the same power source for the router as othe
r
equipment.
Do not open or repair the case yourself. If the router are too hot,
turn off the power immediately and have it repaired at a qualified
service center.
Avoid using this product and all accessories outdoors.
A
ttention
Place the router on a stable surface.
Only use the power adapter that comes with the package. Using
a different voltage rating power adaptor may damage the router.
1
Quick Start Guide
The Front LEDs
BiPAC 7300
BiPAC 7300G
LED Meaning
1 PPP : Lit steady when there is a PPPoA / PPPoE connection.
2 ADSL: Lit when successfully connected to an ADSL DSLAM (“linesync”).
3 LAN Port: Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps.
Blinking when data is Transmitted / Received.
4 WLAN :
(7300G
only)
Lit green when the wireless connection is established.
Flashes when sending/receiving data.
5 SYS : Lit when the system is ready.
6 PWR : Lit when power is ON.
2
Billion BiPAC 7300(G) ADSL2+ Router
The Rear Ports
BiPAC 7300
3
5
2 4
3
BiPAC 7300G
5 4
2
1
3
Port Meaning
1 Power Switch Power ON/OFF switch
2 PWR Connect the supplied power adapter to this jack.
3 RESET
(Emergency/Fai
lure Recovery)
1.After the device is powered on, press it to perform Failure
recover for a dead routers:
Simply hold the Emergency/Failure Recovery Button” when power
on the routers and download the Application if necessary.
2.Perform the Emergency Recover for the missing Password
case:(Using LEDs indications)
Simply hold the Emergency/Failure Recovery Button, when router
can be accessed from GUI, until the LEDs all turn Off, turn On and
then Turn Off. Then, router will perform configuration factory reset
and router reboot.
4 LAN
(RJ-45
connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four
LAN ports when connecting to a PC or an office/home network of
10Mbps or 100Mbps.
5 ADSL
(LINE) Connect the supplied RJ-11 (“telephone”) cable to this port when
connecting to the ADSL/telephone network.
Quick Start Guide
Connecting BiPAC 7300
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR and SYS LEDs are lit steadily and that the relevant LAN LED is lit.
4
Billion BiPAC 7300(G) ADSL2+ Router
Connecting BiPAC 7300G
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR, SYS, and WLAN LEDs are lit steadily and that the relevant LAN LED is
lit.
5
Quick Start Guide
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
6
Billion BiPAC 7300(G) ADSL2+ Router
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the Control
Panel, double-click on Network and Dial-up
Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
7
Quick Start Guide
Configuring PC in Windows 98/Me
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP address
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and
click OK to finish the configuration.
8
Andere Handbücher für BiPAC 7300
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Billion Netzwerk-Router Handbücher
Billion
Billion BiPAC 7800GZ Bedienungsanleitung
Billion
Billion BiPAC 8206AZ Bedienungsanleitung
Billion
Billion 7560 Bedienungsanleitung
Billion
Billion BiPAC 7401V(G)P R4 Bedienungsanleitung
Billion
Billion BiPAC 4700AZ Bedienungsanleitung
Billion
Billion BiPAC 8200N Bedienungsanleitung
Billion
Billion BIPAC 6600 Bedienungsanleitung
Billion
Billion M500 Bedienungsanleitung
Billion
Billion BiPAC 7402G R3 Bedienungsanleitung
Billion
Billion BiPAC 6300VNP Bedienungsanleitung
Billion
Billion BiPAC 7401VP Bedienungsanleitung
Billion
Billion BiPAC 7402G Bedienungsanleitung
Billion
Billion BiPAC 7404V series Bedienungsanleitung
Billion
Billion BiPAC 7800 Bedienungsanleitung
Billion
Billion BiPAC 6300NXL Bedienungsanleitung
Billion
Billion BiPAC 7404V series Bedienungsanleitung
Billion
Billion BiPAC 7401V(G)PX Bedienungsanleitung
Billion
Billion BiPAC 7402 Bedienungsanleitung
Billion
Billion BiPAC 5100S Bedienungsanleitung
Billion
Billion BiPAC 5200G Series Bedienungsanleitung
