Billy Goat QV PUSH Bedienungsanleitung

QV PUSH Operator’s Manual

Part No 27831516 1

QV PUSH VACUUM Operator's Manual

QV550V

Beginning Serial #: 051522001

Accessories Debris bags and Filter

(INCLUDED)

Original Instructions

IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE.

STANDARD

DEBRIS

BAG

Standard on

QV models.

For dusty

conditions.

P/N 831613

DEBRIS AND

DUST SOCK

Traps dust

keeping it

away from the

operator.

P/N 831282

VACUUM

HOSE KIT

5" (127mm) x

10' (3m)

collapsible hose

for vacuuming

in hard-to-reach

areas

P/N 831018

HOOD

FILTER

Filters out

dust from

vacuum

exhaust.

P/N 831226

DEBRIS BAG

SKIRT

Directs dust

away from the

operator.

P/N 831268

ADJUSTABLE

HANDLE

Allows for the

handle to be

raised or

lowered for

comfort.

P/N 831614

NOT FOR REPRODUCTION

QV PUSH Owner’s Manual

Part No 27831508

CONTENTS

SPECIFICATIONS 3

INSTRUCTION LABELS 4

PACKING CHECKLIST AND ASSEMBLY 5

OPERATION AND BAG CARE 6-7

MAINTENANCE AND TROUBLESHOOTING 8-9

ILLUSTRATED PARTS & PARTS LISTS 10-13

NOT FOR REPRODUCTION

QV PUSH Owner’s Manual

Part No 27831508

SPECIFICATIONS

QV550V

HP 5.0 (3.73 kW)

Engine: Type 10V3320003F1

Engine: Fuel Capacity 3.3 qt. (3.1 L)

Engine: Oil Capacity 0.63 qt. (0.60 L)

Total Unit Weight: 180# (81.6 kg)

Overall Length 63” (1.6m)

Overall Width 33” (0.84m)

Overall Height 51” (1.3 m)

Max. operating slope 200

NOT FOR REPRODUCTION

QV PUSH Owner’s Manual

Part No 27831508

INSTRUCTION LABELS

The labels shown below were installed on your BILLY GOAT®QVEU Vacuum. If any labels are damaged or missing, replace

them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for

convenience in ordering replacement labels. The correct position for each label may be determined by referring to the Figure and

Item numbers shown.

LABEL WARNING LABEL THROTTLE

ITEM #35 P/N 831265 ITEM #104 P/N 810656

INSTRUCTION LABEL

ITEM # 37 P/N 831259

ENGINE LABELS

BRIGGS & STRATTON

NOT FOR REPRODUCTION

QV PUSH Owner’s Manual

Part No 27831508

PACKING CHECKLIST

Your Billy Goat is shipped from the factory in one carton, completely assembled except for the nozzle and handle.

PUT OIL IN ENGINE BEFORE STARTING

ASSEMBLY

READ all safety instructions before assembling unit.

TAKE CAUTION when removing the unit from the box.

NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 10-13

1. REMOVE the unit from the box. Be careful as not to damage the unit.

2. REMOVE the bag and attach the handle to the hood using the hardware from the parts bag. The large washer should be on

the inside and the bolt should run from the inside of the hood out. The arch of the handle should be facing to the front of the

machine and the cables shoud not be twisted around each other. NOTE: The left cable should run to the right side of the

transmission and right cable to the left of the transmission. Cable twisting will interfere with the operation of the machine

and will cause premature cable wear.

3. ATTACH the front nozzle (item 7) to the housing and secure it with the serrated hex nuts (item 58) located in the parts bag.

Boxing Parts Checklist

Debris Bag P/N-831225

Dust Sock P/N-831268

Front Nozzle P/N-831606

Literature Assy P/N-831021

Screwcap 5/16”-18 x 1 3/4 qty 4

P/N-8041031

Washer 2” OD x .344 ID qty 4

P/N-810652

Washer 5/16” Flat qty 4

P/N-8171003

Nut Lock 5/16” – 18 qty 4

P/N-8160002

Briggs & Stratton 5.0 HP

PARTS BAG & LITERATURE ASSY

Warranty card P/N- 400972, Operator’s Manual P/N-27831516, Declaration of Conformity P/N-100506. General

Safety and Warnings Manual P/N-100294

NOT FOR REPRODUCTION

QV PUSH Owner’s Manual

Part No 27831508

OPERATION

VACUUM OPERATION

WARNING: The maximum RPM’s on the unit’s engine are set. Altering them from the factory settings could

potentially damage the unit and void warranty.

VACUUM NOZZLE HEIGHT ADJUSTMENT: Adjust by turning the knob clockwise to increase height and counter-clockwise to

lower it. Adjust nozzle height according to surface conditions and debris size. For vacuuming on flat surfaces, set nozzle 1/2"

(12.7 mm) to 5/8" (15.8 mm) above ground. Adjust higher for uneven terrain and turf.

FOR MAXIMUM PICKUP:Adjust nozzle close to debris, but without blocking airflow into the nozzle. NOTE: Never bury nozzle

into debris.

CLEARING A CLOGGED NOZZLE & EXHAUST: Turn engine off and wait for impeller to stop completely and

disconnect spark plug wire. Wearing durable gloves, remove clog, this may require removing the front nozzle.

DANGER, the clog may contain sharp materials. Reconnect spark plug wire.

DEBRIS BAG

Debris bags are normal replaceable wear items.

NOTE:Frequently empty debris to prevent bag overloading with more weight than you can lift. Use the dust skirt when

debris will be vacuumed in dusty conditions.

DO NOT place bag on or near hot surface, such as engine. Run engine at 1/2 throttle for first 1/2 hour to condition new bag.

Your new bag requires a break-in period to condition the pores of the material against premature blockage. The entire bag

surface serves as a filter, and must be able to breathe to have good vacuum performance. Be sure engine has come to a

complete stop before removing or emptying bag.

HOOD FILTER

Hood filters are normal replaceable wear items. The hood filter is for use in dry dusty conditions only. DO NOT get the filter wet.

Clean with light compressed air only.

DUST SOCK

Dust socks are normal replaceable wear items. See next page for dust sock care.

DUSTY CONDITIONS

This vacuum is designed for picking up trash, organic material and other similar debris. However, many vacuums are used where

dust is mixed with trash. Your unit can intermittently vacuum in dusty areas. Dust is the greatest cause of lost vacuum

performance. However, following these rules will help maintain your machine's ability to vacuum in dusty conditions:

•Run machine at idle to quarter throttle.

•The debris bag must be cleaned more frequently. A vacuum with a clean, pillow soft bag will have good pickup

performance. One with a dirty, tight bag will have poor pickup performance. If dirty, empty debris and vigorously shake

bag free of dust. Having one or more spare debris bags is a good way to reduce down time while dirty bags are being

cleaned. DO NOT leave debris in bag while in storage.

NOT FOR REPRODUCTION

QV PUSH Owner’s Manual

Part No 27831508

DUST SOCK CARE AND MAINTENANCE

Purpose: The dust sock acts as a secondary filter lowering the amount of dust that escapes the bag.

Dust socks are to be used in dry and dusty conditions ONLY. Using the dust sock in damp or wet conditions may damage the

dust sock and decrease the effectiveness of the filter.

The dust sock may be installed by simply attaching the mating Velcro strips between the bag and the dust sock. Over time the

dust sock will begin to fill with dust during use. Periodically remove the dust sock, empty the loose dust out and clean the sock.

For a light clean, simply shake the sock, for a deep clean, see below. To remove the sock, simply separate the Velcro.

Dust Sock Care Information:

DO NOT STRIKE THE BAG WITH OR AGAINST OBJECTS DO NOT SNAG THE BAG

DO NOT GET WET

Dust socks are normal replaceable wear items. Replacement P/N- 831282

6”-12”

(152mm-305mm)

LIGHTLY CLEAN WITH COMPRESSED AIR ONLY, FROM THE OUTSIDE IN. KEEP THE

NOZZLE 6-12 INCHES FROM FABRIC

NOT FOR REPRODUCTION

QV PUSH Owner’s Manual

Part No 27831508

MAINTENANCE

NOTE: Items in ( ) can be referenced in the Part Illustrations and Part Lists on pages 10-13.

PERIODIC MAINTENANCE

Periodic maintenance should be performed at the following intervals:

Maintenance Operation Every Use

(daily)

Every 5 hrs

(daily)

Every 10 Hrs Every 25 Hrs Every 50 Hrs

Inspect for loose, worn or damaged parts 

Clean debris bag 

Check tire pressure 

Engine (See Engine Manual)

Check for excessive vibration 

Grease zerks 

Grease: Wheels, Casters, and Shaft Bearings.

Tire air pressure: Check at regular intervals & maintain: Rear SP 13" tires at 20 psi. (137.9 kPa).

IMPELLER REMOVAL

1. Disconnect spark plug wire.

2. Secure the unit to keep it from moving.

3. Remove the nozzle (item 7) from the housing, then remove the plate it was attached to (item 30).

4. Walk the belt (item 22) off of the lower pulley (item 23) and then slide it off of the impeller groove. If you cannot walk it off of

the bottom pulley loosen the bearings (item 24) on the underside this will allow a little more play in the pulley.

5. Slide belt out of belt groove in impeller hub drive pulley.

6. Remove impeller bolt and lock washer.

7. If impeller slides off freely, proceed to (step 12). (Do not drop impeller).

8. If impeller does not slide off crankshaft, place two crowbars between impeller and housing on opposite sides. Pry impeller

away from engine until it loosens. A penetrating oil can help loosen a stuck impeller.

9. Slide impeller off of crank shaft and remove impeller from housing.

10. Reinstall new impeller, new impeller bolt and lock washer in reverse order of removal. (See the Parts Illustration on pages 9-

12 for parts break-down and Parts List on page 10 for proper impeller bolt torque specifications.)

11. When impeller is installed, slide the belt back into the groove on the hub and walk it back onto the bottom pulley. Retighten

the bearings if they were loosened.

12. Reattach nozzle plate and nozzle in reverse order of removal.

13. Reconnect spark plug wire.

14. Check for proper operation.

NOT FOR REPRODUCTION

QV PUSH Owner’s Manual

Part No 27831508

TROUBLESHOOTING

Problem Possible Cause Solution

Abnormal vibration Loose or out of balance impeller or loose engine.

Check impeller and replace if required.

Check engine.

Will not vacuum or has poor

vacuum performance

Dirty debris bag. Nozzle height set too high or low.

Hose kit cap missing. Clogged nozzle or exhaust.

Excessive quantity of debris.

Clean debris bag. Shake bag clean or

wash. Adjust nozzle height. Check for hose

kit cap. Unclog nozzle or exhaust. Allow air to

feed with debris.

Engine will not start

Stop switch off. Throttle in off position. Engine not in

full choke position. Out of gasoline. Bad or old

gasoline. Sparkplug wire disconnected. Dirty air

cleaner. Low oil (honda only).

Check stop switches, throttle, choke

position and gasoline. Connect spark plug

wire. Clean or replace air filter. Or contact a

qualified service person.

Engine is locked, will not pull over Debris locked in impeller. Engine problem.

See page 6. Contact a engine service dealer

for engine problems.

Nozzle scrapes ground in lowest

height setting

Nozzle height out of adjustment.

Adjust nozzle height (See Nozzle height fine

adjustment for hard surfaces on page 6.

NOT FOR REPRODUCTION

QV PUSH Owner’s Manual

Part No 27831508

QV PUSH ENGINE PARTS DRAWING

109

45 108

107

101

105

106

NOT FOR REPRODUCTION

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Billy Goat Rasen- und Gartengeräte Handbücher

Billy Goat

Billy Goat MV650SPH Bedienungsanleitung

Billy Goat

Billy Goat F012507A Bedienungsanleitung

Billy Goat

Billy Goat SC181HGEU Bedienungsanleitung

Billy Goat

Billy Goat PL1801H Bedienungsanleitung

Billy Goat

Billy Goat QL2000VE Montageanleitung

Billy Goat

Billy Goat OS900SPS Bedienungsanleitung

Billy Goat

Billy Goat DL2500SMM Bedienungsanleitung

Billy Goat

Billy Goat AE1300HEU Bedienungsanleitung

Billy Goat

Billy Goat AE403V Bedienungsanleitung

Billy Goat

Billy Goat AE401V Bedienungsanleitung

Billy Goat

Billy Goat SC181H Bedienungsanleitung

Billy Goat

Billy Goat CR551V Bedienungsanleitung

Billy Goat

Billy Goat F1002SPV Bedienungsanleitung

Billy Goat

Billy Goat KD502SPQ Montageanleitung

Billy Goat

Billy Goat BG1002 Montageanleitung

Billy Goat

Billy Goat Quiet Vac SV50HR Montageanleitung

Billy Goat

Billy Goat KVSP Bedienungsanleitung

Billy Goat

Billy Goat LB35 Bedienungsanleitung

Billy Goat

Billy Goat F042508A Bedienungsanleitung

Billy Goat

Billy Goat DL1201L Bedienungsanleitung

Billy Goat

Billy Goat AEH Series Bedienungsanleitung

Billy Goat

Billy Goat BG60AH Montageanleitung

Billy Goat

Billy Goat 440140 Bedienungsanleitung

Billy Goat

Billy Goat KV600SPFB Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung