BioLAB BIFL-201 Bedienungsanleitung

Operation Manual

Ice Flaker

BIFL-201

Thank you very much for Choosing Biolab products. Please read the“Operating Instructions” and “Warranty”

before operating this unit to assure proper operation.

www.biolabscientific.com

Ice Flaker BIFL-201

Index

1. Features.....................................................................................................................03

2. Notes Before Operation.......................................................................................................................03

3. Structure.....................................................................................................................................................04

4. Operation Procedures...........................................................................................................................05

5. Maintenance.............................................................................................................................................05

6. Technical Parameters.............................................................................................................................06

7. Troubleshooting.......................................................................................................................................06

8. Circuit Diagram........................................................................................................................................07

Ice Flaker BIFL-201

www.biolabscientific.com 3

01Features

Our Ice Flaker Series are designed in cubic shape with the curved front panel and curved door (or

stainless steel at front panel and at door) for nice appearance. There are many advantages of the

ice maker, such as quick ice making, great ice making capacity, nice ice shape and ice dropping

quickly. Tap water inlet > water incoming > ice making > crush ice > ice dropping > ice storing, all these

processes are automatically controlled for ice making continuously. In case of water shortage or ice

full in the cabinet, the indicator on the operation board will light on accordingly and the ice maker

will stop operation automatically. The ice storage cabinet is PU foamed, so it is insulated well and it

could prevent the ice made from melting. Also, the remaining water after ice made each time is used

for recycling. So not only the water is saved, but also the ice making eciency is enhanced and the

energy consumption is reduced, and the customer’s ice making cost is also reduced much. Either

puried water or the tap water could be used for ice making.

02Notes Before Operation

1. The incline angle of the cabinet could not be over 45° during transportation. Don’t make ice

maker upside-down in case the compressor or refrigerating system troubles occur.

2. The ake ice maker should be placed on horizontal and structurally sound ground and away

from heat source and corrosive gas. At least about 150mm space should be left around the ice

maker to ensure the ne ventilation.

3. Before using the ake ice maker for the rst time, you should wait 12 hours after positioning it in

a proper place.

4. Voltage range: 187 ~242V(220V) and 100—130V(110V)

5. The rated capacity of wire should be over 6A, the section area of the wire is 0.75mm2.The wire could

be consisted by single ply or multiplies. The rated current of fuse is 5A.

6. The separate three-pole outlet should be used and the grounding must be good.

7. 1f the supply cord is damaged, it must be replaced by the manufacturer, its service agent or simi-

larly qualied persons in order to avoid a hazard.

8. This appliance is not intended for use by children or other persons without assistance or supervision

if their physical, sensory or mental capabilities prevent them from using it safely. Children should be

supervised to ensure that they do not play with the appliance.

www.biolabscientific.com

Ice Flaker BIFL-201

03Structure

1. Switch 5. Ice Shovel 9. Water Outlet Tube

2. Operation Board 6. Back Panel 10. Foot Screw

3. Door 7. Power Cable 11. Water Inlet Tbe

4. Temperature Sensor 8. Screw for Drainage 12. Drainage Tube

Ice Flaker BIFL-201

www.biolabscientific.com 5

04Operation Procedures

1. Unpack the package and take out the attached documents and spare parts such as the wa-

ter inlet and outlet tubes, ice shovel and gaskets, etc.

2. Position the ice maker on a well ventilated place and leave at least 150mm space between

the ice maker and the wall. Be sure the ice maker is positioned levelly and away from the heat

source.

3. Make one end of the Φ12 exible plastic corrugated pipe (supplied with the maker) connect-

ed with the water outlet tube on back of the maker, another pipe end should be placed in a

container for surplus water (prepared by user himself) or in the sewer.

4. Make one end of the water inlet tube (supplied with the maker)connected with the 3/4” screw

type connector of the water tap so as to get the drinkable tap water. The water pressure of wa-

ter supply pipe is 1.5 ~ 3 bar. The other end of the water inlet tube should be connected with

the screw type connector of water valve on the back of the ice maker. Be sure to put gaskets

(supplied with the maker) in both ends of the water inlet tube before connecting. If it is an ice

maker for puried water, a Φ12 corrugated pipe (supplied with the maker) should be used.

Connect one end of the pipe with the puried water supplier (desk-top water dispenser) and

another end with water valve connector on the back of the ice maker. The desk-top water

dispenser should be placed on the ice maker at the back position.

5. Make poser connection and press on the start button on the operation board for about 4

seconds till the run indicator and the big ice indicator (or small ice indicator) light on. Then the

maker begins to work. All the procedures, water inlet > ice making > crush ice > ice dropping >

ice storing, are controlled automatically for ice making continuously. If ice is full in the ice stor-

age container, the ice full indicator on the operation board will light on and ice maker will stop

automatically. If there is a water shortage or something wrong with the water supply system,

the Water shortage indicator will light on and the ice maker will stop operation automatically.

05Maintainence

1. If the compressor stops for any reasons like water shortage, too much ice, power o, etc., don’t restart

it right away. You can restart it about 5 minutes later.

2. Check regularly the connectors of the water inlet and outlet tubes and drain the little surplus water

that may leak.

3. If the ice make will be unused for a long period, please o the plastic drainage connector screw

on the back of the ice maker so as to drain the surplus water in the water groove. Then screw it on.

Wipe the inner liner of the ice storage container with a clean rag.

4. When plugging or unplugging, the plug should be held by hand and the wires should not be

dragged heavily.

www.biolabscientific.com

Ice Flaker BIFL-201

06Technical Parameters

Model BIFL-201

Capacity 20 kg/24 h

Storage Bin Capacity 10 kg

Refrigerant R134a

Condenser Type Air cooled

Overall Dimension 330x470x605 mm

Weight 28/31 kg

Power 280 W

Power Supply 220 V, 60 Hz

The specications are subject to be changed without notice. Please check the nameplate for sure.

07Troubleshooting

(FOR REFERENCE OF USERS AND TECHNICIANS)

TROUBLE CAUSE REMEDY

The Ice Flaker does not

work.

1. The voltage is lower than

the lower limitation

2. The ambient temperature is

too low (Lower than 10 °C)

1. Stop the ice maker and restart it

until the voltage is normal.

2. Try again when the ambient

temperature higher than 10 ° C

Water shortage

indicator light on.

1. Water shortage from the

water supply system.

2. Water valve damage.

3. Tap water pressure too low

1. Check the water supply. If ii is

OK, restart the maker.

2. Check the water valve.

3. Be sure the tap water pressure is

higher than 1.5 bar.

Compressor does not

work.

1. Water shortage.

2. Ice full.

1. Check the water supply system

(water valve and water supply

tube).

2. Take o some ice.

Ice Flaker BIFL-201

www.biolabscientific.com 7

Compressor works, but

no ice is made.

1. Refrigerant leakage.

2. The refrigerating system is

blocked.

1. Recharge the refrigerant and

check the leakage again.

2. Charging N2 to check whether

the sysem is blocked and

replace the ller.

3. Check whether le fan is

running

Water shortage

indicator and ice full

indicator are glittering

at the same time.

If water inlet jam or running

failure because of low

environmental temperature.

Stop the machine until the

temperature reaches lOU or repair

it by authorized service people.

08Circuit Diagram

BIOLAB SCIENTIFIC LIMITED

91 Traord Crescent, Markham, Ontario,

L3R 7J3, Canada

+1 707 533 1445 [email protected] www.biolabscientific.com

Inhaltsverzeichnis

Andere BioLAB Laborausrüstung Handbücher

BioLAB

BioLAB BCLT-202 Bedienungsanleitung

BioLAB

BioLAB BIGP-502 Bedienungsanleitung

BioLAB

BioLAB BCLT-201 Bedienungsanleitung

BioLAB

BioLAB BLVR-202 Bedienungsanleitung

BioLAB

BioLAB BTUR-303 Bedienungsanleitung

BioLAB

BioLAB BCMI-505 Bedienungsanleitung

BioLAB

BioLAB BIFL-208 Bedienungsanleitung

BioLAB

BioLAB BLVR-101 Bedienungsanleitung

BioLAB

BioLAB BCBS-103 Bedienungsanleitung

BioLAB

BioLAB BAHZ 400 B Series Bedienungsanleitung

BioLAB

BioLAB BMRW-104 Bedienungsanleitung

BioLAB

BioLAB BHMS-104 Bedienungsanleitung

BioLAB

BioLAB BSFLS-101 Bedienungsanleitung

BioLAB

BioLAB BBWA-100 Bedienungsanleitung

BioLAB

BioLAB BIDP 100 Series Bedienungsanleitung

BioLAB

BioLAB BDIB-103 Bedienungsanleitung

BioLAB

BioLAB BBBF-106 Bedienungsanleitung

BioLAB

BioLAB BCLT-203 Bedienungsanleitung

BioLAB

BioLAB 200 Series Bedienungsanleitung

BioLAB

BioLAB BIFL-203 Bedienungsanleitung

BioLAB

BioLAB BODR 100 Series Bedienungsanleitung

BioLAB

BioLAB BFSD-502 Bedienungsanleitung

BioLAB

BioLAB BVMX-201 Bedienungsanleitung

BioLAB

BioLAB BCBHR-304 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung