BIRD 4042 Bedienungsanleitung

Channel Power Sensor

Model 4042

Operation Manual

by Bird Technologies, Inc.

Instruction Book Part Number 920-4042 Rev. C

Safety Precautions

The following are general safety precautions that are not necessarily related to

any specific part or procedure, and do not necessarily appear elsewhere in this

publication. These precautions must be thoroughly understood and apply to all

phases of operation and maintenance.

WARNING

Keep Away From Live Circuits

Operating Personnel must at all times observe general safety precautions. Do

not replace components or make adjustments to the inside of the test

equipment with the high voltage supply turned on. To avoid casualties, always

remove power.

WARNING

Shock Hazard

Do not attempt to remove the RF transmission line while RF power is present.

WARNING

Do Not Service Or Adjust Alone

Under no circumstances should any person reach into an enclosure for the

purpose of service or adjustment of equipment except in the presence of

someone who is capable of rendering aid.

WARNING

Safety Earth Ground

An uninterruptible earth safety ground must be supplied from the main

power source to test instruments. Grounding one conductor of a two

conductor power cable is not sufficient protection. Serious injury or death can

occur if this grounding is not properly supplied.

WARNING

Resuscitation

Personnel working with or near high voltages should be familiar with modern

methods of resuscitation.

WARNING

Remove Power

Observe general safety precautions. Do not open the instrument with the

power applied.

Safety Precautions

Safety Symbols

Note: Calls attention to supplemental information.

Warning Statements

The following safety warnings appear in the text where there is danger to

operating and maintenance personnel, and are repeated here for emphasis.

Refer to page 4.

WARNING

Warning notes call attention to a procedure, which if not correctly performed,

could result in personal injury.

CAUTION

Caution notes call attention to a procedure, which if not correctly performed,

could result in damage to the instrument.

WARNING

Leaking RF energy is a potential health hazard. Never attempt to connect or

disconnect equipment from the transmission line while RF power is being

applied. Severe burns, electrical shock, or death can occur.

Channel Power Sensor 4042

iii

Safety Statements

USAGE

ANY USE OF THIS INSTRUMENT IN A MANNER NOT SPECIFIED BY

THE MANUFACTURER MAY IMPAIR THE INSTRUMENT’S SAFETY

PROTECTION.

USO

EL USO DE ESTE INSTRUMENTO DE MANERA NO ESPECIFICADA

POR EL FABRICANTE, PUEDE ANULAR LA PROTECCIÓN DE

SEGURIDAD DEL INSTRUMENTO.

BENUTZUNG

WIRD DAS GERÄT AUF ANDERE WEISE VERWENDET ALS VOM

HERSTELLER BESCHRIEBEN, KANN DIE GERÄTESICHERHEIT

BEEINTRÄCHTIGT WERDEN.

UTILISATION

TOUTE UTILISATION DE CET INSTRUMENT QUI N’EST PAS

EXPLICITEMENT PRÉVUE PAR LE FABRICANT PEUT

ENDOMMAGER LE DISPOSITIF DE PROTECTION DE

L’INSTRUMENT.

IMPIEGO

QUALORA QUESTO STRUMENTO VENISSE UTILIZZATO IN MODO

DIVERSO DA COME SPECIFICATO DAL PRODUTTORE LA

PROZIONE DI SICUREZZA POTREBBE VENIRNE COMPROMESSA.

Safety Precautions

SERVICE

SERVICING INSTRUCTIONS ARE FOR USE BY SERVICE - TRAINED

PERSONNEL ONLY. TO AVOID DANGEROUS ELECTRIC SHOCK, DO

NOT PERFORM ANY SERVICING UNLESS QUALIFIED TO DO SO.

SERVICIO

LAS INSTRUCCIONES DE SERVICIO SON PARA USO EXCLUSIVO

DEL PERSONAL DE SERVICIO CAPACITADO. PARA EVITAR EL

PELIGRO DE DESCARGAS ELÉCTRICAS, NO REALICE NINGÚN

SERVICIO A MENOS QUE ESTÉ CAPACITADO PARA HACERIO.

WARTUNG

ANWEISUNGEN FÜR DIE WARTUNG DES GERÄTES GELTEN NUR

FÜR GESCHULTES FACHPERSONAL. ZUR VERMEIDUNG

GEFÄHRLICHE, ELEKTRISCHE SCHOCKS, SIND

WARTUNGSARBEITEN AUSSCHLIEßLICH VON QUALIFIZIERTEM

SERVICEPERSONAL DURCHZUFÜHREN.

ENTRENTIEN

L’EMPLOI DES INSTRUCTIONS D’ENTRETIEN DOIT ÊTRE RÉSERVÉ

AU PERSONNEL FORMÉ AUX OPÉRATIONS D’ENTRETIEN. POUR

PRÉVENIR UN CHOC ÉLECTRIQUE DANGEREUX, NE PAS

EFFECTUER D’ENTRETIEN SI L’ON N’A PAS ÉTÉ QUALIFIÉ POUR

CE FAIRE.

ASSISTENZA TECNICA

LE ISTRUZIONI RELATIVE ALL’ASSISTENZA SONO PREVISTE

ESCLUSIVAMENTE PER IL PERSONALE OPPORTUNAMENTE

ADDESTRATO. PER EVITARE PERICOLOSE SCOSSE ELETTRICHE

NON EFFETTUARRE ALCUNA RIPARAZIONE A MENO CHE

QUALIFICATI A FARLA.

Channel Power Sensor 4042

About This Manual

This manual covers the operating and maintenance instructions for the

following models:

Changes to this Manual

We have made every effort to ensure this manual is accurate. If you discover any

errors, or if you have suggestions for improving this manual, please send your

comments to our Solon, Ohio factory. This manual may be periodically updated.

When inquiring about updates to this manual refer to the part number and

revision on the title page.

Chapter Layout

Introduction — Describes the features of the 4042 Channel Power Sensor.

Installation — Describes how to set up and prepare the 4042 Power Sensor for

use.

Maintenance — This section provides the specifications for the 4042 Power

Sensor as well as a model identification table.

4042 Series - Channel Power Sensors

Table of Contents

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i

Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

Warning Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

Safety Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Changes to this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Chapter Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Purpose and Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Channel Sensor Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Data Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Power Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

CPM Serial Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 3 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Model Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Chapter 1 Introduction

Purpose and Function

The Bird 4042 Series Channel Power Sensors are digital power sensors designed

for use with the Bird Channel Power Monitor (CPM).

The 4042 Series Channel power sensors are typically used to measure forward

and reflected average power on a 50 ohm RF transmission line with maximum

500 watt forward and reflected power levels in a frequency band with an overall

range of 100 to 1000 MHz. The 4042 sensor also provides VSWR readings.

Figure 1 Bird 4042 Series Channel Power Sensor

Features

RF Input N-Type (male) connector (shown), other connector types

available, see

"Model Identification" on page 8

RF Output N-Type (female) connector (shown), other connector types

available, see

"Model Identification" on page 8

Data Connectors

RJ-25 connector provides power and data connection. Only

one connector is required, second connector may be used to

extend RS-485 bus to additional digital sensors.

RJ-25 termination plug must be installed in unused jack.

Button Not Connected.

Status LED Solid green: Power applied.

INPUT

DATA

CONNECTORS

OUTPUT

BUTTON

STATUS

LED







4042 Channel

Power Sensor







Introduction

Channel Sensor Operation

The 4042 Channel Sensor is a unique sensor that is able to measure the forward

power, reflected power and VSWR of a SINGLE CHANNEL in the presence of

multiple channels at the output of a frequency combiner (see

Figure 3 on

page 4

The sensor can also measure the forward power, reflected power and the VSWR

of the composite signal by scanning up to 16 individual channels and summing

their power, see

Figure 2

Composite Signal

Frequency

Range

100 to 1000 MHz

Up to 16

Channels

Selectable

Frequency

and

Bandwidth

for each

Channel

769.14375

770.64375

770.24375

25 kHz

12.5 kHz

6.25 kHz

Freq:

BW:

Channel Sensor Configuration

Once connected to a CPM and RF Transmission line, the sensor may be

programmed to measure power and VSWR for up to 16 frequencies or channels.

The bandwidth of each channel is selectable and may be set to one of the

following values:

6.25 kHz

12.5 kHz

25 kHz

The CPM can be setup to provide low power and VSWR alarms for all 16

channels monitored by the 4042 Sensor.

Channel Power Sensor 4042

Data Connection

The 4042 Channel Sensor uses an RS-485 serial bus for data transfer to and from

a CPM. Each sensor is equipped with two RJ-25 jacks, either jack may be

connected to a CPM. The second RJ-25 jack may be used to extend the RS-485

bus to another digital sensor. See

Figure 3 on page 4

. Multiple digital sensors

may be serially connected in this fashion, allowing as many as 16 sensors to be

connected to a CPM.

If multiple sensors are to be connected serially, each one is assigned a unique

address via the CPM. When each sensor is connected to the CPM, prior to

connecting any additional sensors, add sensor in the CPM to assign an address,

only then may an additional sensor be connected serially.

A termination plug must be used in the open RJ-25 jack on the rear panel of the

CPM or the open RJ-25 jack of the final digital sensor in the chain.

Inhaltsverzeichnis

Andere BIRD Messgerät Handbücher

BIRD

BIRD 4308 Bedienungsanleitung

BIRD

BIRD Termaline 8920 Series Bedienungsanleitung

BIRD

BIRD SignalHawk SH-36S-PC Konfigurationshandbuch

BIRD

BIRD 7027 Series Bedienungsanleitung

BIRD

BIRD Termaline 8860SC Series Bedienungsanleitung

BIRD

BIRD Thruline 43 Bedienungsanleitung

BIRD

BIRD Digital Power Meter Display Bedienungsanleitung

BIRD

BIRD THRULINE 4421 Bedienungsanleitung

BIRD

BIRD Thruline 43 Bedienungsanleitung

BIRD

BIRD 4421-250 Bedienungsanleitung

BIRD

BIRD THRULINE 4027F series Bedienungsanleitung

BIRD

BIRD TERMALINE 8135 Bedienungsanleitung

BIRD

BIRD SignalHawk SH-60S-TC Bedienungsanleitung

BIRD

BIRD Thruline 4410A500 Bedienungsanleitung

BIRD

BIRD 4421A Bedienungsanleitung

BIRD

BIRD Wattcher 3127A Bedienungsanleitung

BIRD

BIRD ACM Series Bedienungsanleitung

BIRD

BIRD 5000-XT Bedienungsanleitung

BIRD

BIRD IQC5000B Bedienungsanleitung

BIRD

BIRD THRULINE 43 Series Bedienungsanleitung

BIRD

BIRD Termaline 8920 Series Bedienungsanleitung

BIRD

BIRD 4422 Bedienungsanleitung

BIRD

BIRD SignalHawk SH-36S-RM Bedienungsanleitung

BIRD

BIRD SiteHawk SK-6000-TC Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung