Black Box LGC121A-R3 Bedienungsanleitung

LGC120A-R2 Rev. 1 56-80630BB-00 Rev. C2

LGC120A-R2 LGC125A-R2

LGC121A-R3LGC126A-R2

LGC122A-R2 LGC127A-R2

LGC124A-R2 LGC128A-R2

Miniature Media Converter 10/100/1000 Switching

Connect Ethernet, Fast Ethernet, or Gigabit

Ethernet copper ports to 1000-Mbps multimode

duplex, single-mode duplex, or single-mode

single-strand fiber optic cable.

Page 2 877-877-2269 | blackbox.com LGC120A-R2

TRADEMARKS USED IN THIS MANUAL

Black Box and the Double Diamond logo are registered trademarks of BB

Technologies, Inc.

Any other trademarks mentioned in this manual are acknowledged to be the

property of the trademark owners.

Notes

LGC120A-R2 877-877-2269 | blackbox.com Page 15

Notes

FCC and IC RFI Statements

LGC120A-R2 877-877-2269 | blackbox.com Page 3

FCC and Industry Canada RF Interference Statements

Class A Digital Device. This equipment has been tested and found to comply with

the limits for a Class A computing device pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. This equipment generates,

uses, and can radiate radio frequency energy, and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. If this equipment does cause harmful interference to radio or

telephone reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•Consult an experienced radio/TV technician for help.

CAUTION

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

To meet FCC requirements, shielded cables and power cords are required to

connect this device to a personal computer or other Class A certified device.

This digital apparatus does not exceed the Class A limits for radio noise emission

from digital apparatus set out in the Radio Interference Regulation of Industry

Canada.

Certifications

Page 4 877-877-2269 | blackbox.com LGC120A-R2

Certifications

European Directive 2002/96/EC (WEEE) requires that any equipment that

bears this symbol on product or packaging must not be disposed of with

unsorted municipal waste. This symbol indicates that the equipment should be

disposed of separately from regular household waste. It is the consumer’s

responsibility to dispose of this and all equipment so marked through

designated collection facilities appointed by government or local authorities.

Following these steps through proper disposal and recycling will help prevent

potential negative consequences to the environment and human health. For

more detailed information about proper disposal, please contact local

authorities, waste disposal services, or the point of purchase for this equipment.

Class 1 Laser product, Luokan 1 Laserlaite,

Laser Klasse 1, Appareil A’Laser de Classe

Chapter 7: Electrostatic Discharge Precautions

LGC120A-R2 877-877-2269 | blackbox.com Page 13

7. Electrostatic Discharge Precautions

Electrostatic discharge (ESD) can cause damage to any product, add-in

modules or stand alone units, containing electronic components. Always

observe the following precautions when installing or handling these kinds of

products.

1. Do not remove unit from its protective packaging until ready to install.

2. Wear an ESD wrist grounding strap before handling any module or component.

If the wrist strap is not available, maintain grounded contact with the system unit

throughout any procedure requiring ESD protection.

3. Hold the units by the edges; do not touch the electronic components or gold

connectors.

4. After removal, always place the boards on a grounded, static-free surface, ESD

pad or in a proper ESD bag. Do not slide the modules or stand alone units over

any surface.

WARNING! Integrated circuits and fiber optic components

are extremely susceptible to electrostatic discharge damage.

Do not handle these components directly unless you are a

qualified service technician and use tools and techniques that

conform to accepted industry practices.

877-877-2269

Chapter 6: Fiber Optic Cleaning Guidelines

Page 12 877-877-2269 | blackbox.com LGC120A-R2

6. Fiber Optic Cleaning Guidelines

Fiber Optic transmitters and receivers are extremely susceptible to

contamination by particles of dirt or dust, which can obstruct the optic path and

cause performance degradation. Good system performance requires clean

optics and connector ferrules.

1. Use fiber patch cords (or connectors, if you terminate your own fiber) only from a

reputable supplier; low-quality components can cause many hard-to-diagnose

problems in an installation.

2. Dust caps are installed at Black Box to ensure factory-clean optical devices.

These protective caps should not be removed until the moment of connecting the

fiber cable to the device. If you need to disconnect the fiber device, reinstall the

protective dust caps.

3. Store spare caps in a dust-free environment such as a sealed plastic bag or box

so that when reinstalled they do not introduce any contamination to the optics.

4. If you suspect that the optics have been contaminated, alternate between

blasting with clean, dry, compressed air and flushing with methanol to remove

particles of dirt.

Table of Contents

LGC120A-R2 877-877-2269 | blackbox.com Page 5

Table of Contents

Part Numbers ......................................................................................................6

1. Specifications ......................................................................................... 7

2. Overview: About the Miniature Media Converter 10/100/1000

Switching ................................................................................................ 8

3. Install the Miniature Media Converter 10/100/1000 Switching............... 9

3.1Powering the Miniature Media Converter 10/100/1000 Switching ......... 9

4. Operation.............................................................................................. 10

4.1LED Operation...................................................................................... 10

5. Contacting Black Box ........................................................................... 11

6. Fiber Optic Cleaning Guidelines ..........................................................12

7. Electrostatic Discharge Precautions ....................................................13

Part Numbers

Page 6 877-877-2269 | blackbox.com LGC120A-R2

Part Numbers

Part Number Description

LGC120A-R2 TX/SX-MM850-SC

LGC121A-R3 TX/LX-SM1310-SC

LGC122A-R2 TX/LX-SM1310/PLUS-SC

LGC124A-R2 TX/LX-SM1550/LONG-SC

LGC125A-R2 TX/SSLX-SM1310-SC (1310xmt/1550rcv)

LGC126A-R2 TX/SSLX-SM1550-SC (1550xmt/1310rcv)

LGC127A-R2 TX/SSLX-SM1310/PLUS-SC (1310xmt/1550rcv)

LGC128A-R2 TX/SSLX-SM1550/PLUS-SC (1550xmt/1310rcv)

Chapter 5: Contacting Black Box

LGC120A-R2 877-877-2269 | blackbox.com Page 11

5. Contacting Black Box

Black Box Customer Service

Order toll-free in the U.S.: Call 877-877-BBOX

(outside U.S. call 724-746-5500)

Free technical support, 24 hours a day, 7 days a week.

Call: 877-877-2269 or Fax: 724-746-0746

Mail order: Black Box Corporation

1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com

E-mail: info@blackbox.com

Chapter 4: Operation

Page 10 877-877-2269 | blackbox.com LGC120A-R2

4. Operation

4.1 LED Operation

Each module features diagnostic LEDs that provide information on features and

ports.

FX LNK/ACT Glows green when a link is established on the fiber port;

blinks green when activity is detected on the fiber port.

TX LNK/ACT Glows amber when a link is established on the copper port;

blinks amber when activity is detected on the copper port.

Chapter 1: Specifications

LGC120A-R2 877-877-2269 | blackbox.com Page 7

1. Specifications

AC Wall Adapter 100 to 240 ±10% VAC input, 5 VDC output, 2A max.

Operating

Temperature

+32°F to +122°F (0°C to +50°C)

Storage Temperature -31°C to +167°F (-35°C to +75°C)

Humidity 5% to 95% (non-condensing); 0 to 10,000 ft. altitude

Ethernet Connections 10/100/1000 BaseT, Auto Negotiation, Auto-Cross,

Flow Control, 1536 MTU, Full Line-Rate Forwarding

Dimensions 0.83”H x 1.80”W x 3.35”D (2.11 x 4.57 x 8.51 cm)

NOTE: The media converters are now compliant to EN62368.

Chapter 2: Overview

Page 8 877-877-2269 | blackbox.com LGC120A-R2

2. Overview: About the Miniature Media Converter 10/100/1000

Switching

The Miniature Media Converter 10/100/1000 Switching is a 10/100/1000 Auto

Negotiating, switching miniature media converter. The fiber port always

operates at 1000 Mbps FDX; the copper port Auto Negotiates the connected

device’s speed and duplex mode: 10 Mbps, 100 Mbps or 1000 Mbps, and HDX

or FDX (including Flow Control).

The Miniature Media Converter 10/100/1000 Switching offers plug-and-play

operation, including the AutoCross feature which automatically selects between

a crossover work-station or pass-through repeater hub connection depending

on the connected device.

Chapter 3: Install the Miniature Media Converter 10/100/1000 Switching

LGC120A-R2 877-877-2269 | blackbox.com Page 9

3. Install the Miniature Media Converter 10/100/1000 Switching

The Miniature Media Converter 10/100/1000 Switching installs in a Black Box

PowerTray 18-slot or can be used as a standalone media converter. As a

standalone, the Miniature Media Converter 10/100/1000 Switching uses a

universal external switching power cube with 100 – 240 ±10% VAC input and

5 VDC output.

3.1 Powering the Miniature Media Converter 10/100/1000 Switching

The Miniature Media Converter includes multiple powering options:

•A country-specific, high-reliability AC power adapter (included)

•The IEEE 802.3af Power over Ethernet standard; draws power from power

sourcing equipment

•PowerTray 18-slot for Rackmounting

Chapter 2: Overview

Page 8 877-877-2269 | blackbox.com LGC120A-R2

2. Overview: About the Miniature Media Converter 10/100/1000

Switching

The Miniature Media Converter 10/100/1000 Switching is a 10/100/1000 Auto

Negotiating, switching miniature media converter. The fiber port always

operates at 1000 Mbps FDX; the copper port Auto Negotiates the connected

device’s speed and duplex mode: 10 Mbps, 100 Mbps or 1000 Mbps, and HDX

or FDX (including Flow Control).

The Miniature Media Converter 10/100/1000 Switching offers plug-and-play

operation, including the AutoCross feature which automatically selects between

a crossover work-station or pass-through repeater hub connection depending

on the connected device.

Chapter 3: Install the Miniature Media Converter 10/100/1000 Switching

LGC120A-R2 877-877-2269 | blackbox.com Page 9

3. Install the Miniature Media Converter 10/100/1000 Switching

The Miniature Media Converter 10/100/1000 Switching installs in a Black Box

PowerTray 18-slot or can be used as a standalone media converter. As a

standalone, the Miniature Media Converter 10/100/1000 Switching uses a

universal external switching power cube with 100 – 240 ±10% VAC input and

5 VDC output.

3.1 Powering the Miniature Media Converter 10/100/1000 Switching

The Miniature Media Converter includes multiple powering options:

•A country-specific, high-reliability AC power adapter (included)

•Via the optional USB Power Adapter Cable (LHC021A or LGC022A)

connected to computer’s USB port

•PowerTray 18-slot for Rackmounting

Chapter 4: Operation

Page 10 877-877-2269 | blackbox.com LGC120A-R2

4. Operation

4.1 LED Operation

Each module features diagnostic LEDs that provide information on features and

ports.

FX LNK/ACT Glows green when a link is established on the fiber port;

blinks green when activity is detected on the fiber port.

TX LNK/ACT Glows amber when a link is established on the copper port;

blinks amber when activity is detected on the copper port.

Chapter 1: Specifications

LGC120A-R2 877-877-2269 | blackbox.com Page 7

1. Specifications

AC Wall Adapter 100 to 240 ±10% VAC input, 5 VDC output, 2A max.

Operating

Temperature

+32°F to +122°F (0°C to +50°C)

Storage Temperature -31°C to +167°F (-35°C to +75°C)

Humidity 5% to 95% (non-condensing); 0 to 10,000 ft. altitude

Ethernet Connections 10/100/1000 BaseT, Auto Negotiation, Auto-Cross,

Flow Control, 1536 MTU, Full Line-Rate Forwarding

Dimensions 0.83”H x 1.80”W x 3.35”D (2.11 x 4.57 x 8.51 cm)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Black Box Medienkonverter Handbücher

Black Box

Black Box AVSC-HDMI-VGA Bedienungsanleitung

Black Box

Black Box IC081A Bedienungsanleitung

Black Box

Black Box LMC5207A-R2 Bedienungsanleitung

Black Box

Black Box AC135A-R2 Bedienungsanleitung

Black Box

Black Box LGC215A Bedienungsanleitung

Black Box

Black Box LME020A Bedienungsanleitung

Black Box

Black Box LGC5150A Bedienungsanleitung

Black Box

Black Box IC940A-F Bedienungsanleitung

Black Box

Black Box G.703/V.35 Bedienungsanleitung

Black Box

Black Box IC832A Bedienungsanleitung

Black Box

Black Box LH2001A-ST-R3 Bedienungsanleitung

Black Box

Black Box USB Director RS-232 Bedienungsanleitung

Black Box

Black Box AC425A Bedienungsanleitung

Black Box

Black Box AVSC-VIDEO-HDMI Kurzanleitung

Black Box

Black Box MCX S7 Series Gebrauchsanweisung

Black Box

Black Box LMC280A Gebrauchsanweisung

Black Box

Black Box IC700A Bedienungsanleitung

Black Box

Black Box IC558A Bedienungsanleitung

Black Box

Black Box PCA36A Bedienungsanleitung

Black Box

Black Box LMC5207A Bedienungsanleitung

Black Box

Black Box AC345A-R2 Bedienungsanleitung

Black Box

Black Box LG6630C Bedienungsanleitung

Black Box

Black Box KVUSB-PS2 Bedienungsanleitung

Black Box

Black Box JHN2110A Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung