Black Box MEDIACENTO IPX 4K Bedienungsanleitung

STEP X - Name of Step

24/7 TECHNICAL SUPPORT AT 877.877.2269 OR VISIT BLACKBOX.COM

VX-HDMI-4KIP-TX, VX-HDMI-4KIP-RX

MEDIACENTO

IPX 4K

QUICK START GUIDE

STEP 1 - Check the Package Contents

VX-HDMI-4KIP-TX PACKAGE CONTENTS

• (1) MEDIACENTO IPX 4K TRANSMITTER

• (1) 5-VDC, 3-A POWER SUPPLY

• (1) IR BLASTER CABLE

• (1) USB 2.0 CABLE

• (1) AUDIO/MIC CABLE

VX-HDMI-4KIP-RX PACKAGE CONTENTS

• (1) MEDIACENTO IPX 4K RECEIVER

• (1) 5-VDC, 3-A POWER SUPPLY

• (1) IR RECEIVER CABLE

• (1) IR REMOTE CONTROL

ADDITONAL ITEMS YOU MAY NEED

• (1) FIBER OPTIC SFP MODULE PER TX

OR RX UNIT (SEE TABLE 1, BELOW)

TABLE 1. COMPATIBLE SFPS

PRODUCT CODE DESCRIPTION

LFP411 SFP, 1250-Mbps Fiber with Extended Diagnostics, 850-nm Multimode, 550 m LC

LFP412 SFP, 1250-Mbps Fiber with Extended Diagnostics, 1310-nm Multimode, 2 km LC

LFP413 SFP, 1250-Mbps Fiber with Extended Diagnostics, 1310-nm Single-Mode, 10 km LC

LFP414 SFP, 1250-Mbps Fiber with Extended Diagnostics, 1310-nm Single-Mode, 30 km LC

LFP418 SFP, 1250-Mbps Fiber with Extended Diagnostics, 1550-nm Single-Mode, 80 km, LC

NOTE: Also should support most gigabit fiber

SFP modules.

STEP 2A - Transmitter (TX) Front Panel

TABLE 2. TRANSMITTER FRONT PANEL COMPONENTS

NUMBER IN

DIAGRAM ABOVE COMPONENT DESCRIPTION

1DB9 connector Serial over IP RS-232 extension port, connects to source

device

2a Power ON Status LED Lights steady when power on sequence is completed

2b Link LED Indicates LAN Link status

3a Set/Reset button Press to set a function, reset system or reset to default

3b Select button Select EDID, video profile or video channel

4a EDID LED Indicates EDID update status

4b V. Profile LED Indicates video/graphic mode

5Video Channel LED 7-segment LED display indicates Video Channel

6CH+/CH- pushbuttons Press to change video channel

1 2 3 4 5 6 7 8 9 10 11

STEP 2A (CONTINUED) - Transmitter (TX) Front Panel

TABLE 2 (CONTINUED). TRANSMITTER FRONT PANEL COMPONENTS

NUMBER IN

DIAGRAM ABOVE COMPONENT DESCRIPTION

7IR Emitter connector Used for emitting signal of IR extension over IP

8IR Receiver connector Used for receiving signal of IR extension over IP

9Audio connector Connects to analog audio output (speaker)

10 Audio connector Connects to analog audio input (microphone)

11 USB Type B connector Links to host source device for USB extension over IP

1 2 3 4 5 6 7 8 9 10 11

STEP 2B - Transmitter (TX) Back Panel

1 2 3 4 5

TABLE 3. TRANSMITTER BACK PANEL COMPONENTS

NUMBER IN

DIAGRAM ABOVE COMPONENT DESCRIPTION

1 SFP cage Fiberoptic module for link between TX and RX installs here

2RJ-45 connector Used for LAN Link between TX and RX/Gigabit Ethernet switch

3HDMI IN connector Connects to HDMI source for HDMI extension over IP

4HDMI OUT connector Loops back the source signal to TX unit's connected display

5 5-VDC jack Links to 5-VDC power supply

STEP 3A - Receiver (RX) Front Panel

TABLE 4. RECEIVER FRONT PANEL COMPONENTS

NUMBER IN

DIAGRAM ABOVE COMPONENT DESCRIPTION

1DB9 connector Serial over IP RS-232 extension port, connects to sink device

2a Power ON Status LED Lights steady when power on sequence is completed

2b Link LED Indicates LAN Link status

2c SFP LED Indicates Fiber Link status

3a Set/Reset button Press to set a function, reset system or reset to default

3b Select button Select EDID, video profile or video channel

4a EDID LED Indicates EDID update status

4b USB Link LED Indicates USB link status

4c V. Profile LED Indicates video/graphic mode

5Video Channel LED 7-segment LED display indicates Video Channel

1 2 3 4 5 6 7 8 9 10 11 12

STEP 3A (CONTINUED) - Receiver (RX) Front Panel

TABLE 4 (CONTINUED). RECEIVER FRONT PANEL COMPONENTS

NUMBER IN

DIAGRAM AT LEFT COMPONENT DESCRIPTION

6CH+/CH- pushbuttons Press to change video channel

7IR Emitter connector Used for emitting signal of IR extension over IP

8IR Receiver connector Used for receiving signal of IR extension over IP

9Audio connector Connects to analog audio input (microphone)

10 Audio connector Connects to analog audio output (speaker)

11 (2) USB Type A connectors Links to USB 2.0 devices for USB extension over IP

12 (2) USB Type A connectors Links to USB HID keyboard/mouse for USB extension

over IP

STEP 3B - Receiver (RX) Back Panel

TABLE 5. RECEIVER BACK PANEL COMPONENTS

NUMBER IN

DIAGRAM ABOVE COMPONENT DESCRIPTION

1 SFP cage Fiberoptic module for link between TX and RX installs here

2RJ-45 connector Used for LAN Link between TX and RX/Gigabit Ethernet switch

3HDMI OUT connector Connects to HDMI sink for HDMI extension over IP

4 5-VDC jack Links to 5-VDC power supply

1 2 3 4

STEP 4 - Network Setup and Hardware Switching

NETWORK SETUP AND HW SWITCHING

1. Power on the Gigabit Switch and enable

Jumbo Frame (8k) and IGMP v2.

2. Connect all transmitters and receivers

to the Gigabit Switch using CATx cables.

3. Connect all transmitters with video sources,

and all receivers with Display/TV using HDMI

cables.

4. Connect an IR emitter cable to the

transmitter’s or receiver’s IR Emitter Jack,

and point the IR emitter to transmitter’s

or receiver’s connected device’s IR receiver

window that you want to control.

5. Connect an IR Receiver cable to the

transmitter’s or receiver’s IR Receiver Jack,

and point the IR receiver to the transmitter’s

or receiver’s connected device’s IR remote.

6. Connect an RS-232 cable to the transmitter

and receiver where a RS-232 controller

or Display/TV/device can take RS-232

command.

NOTE: If the transmitter’s or receiver’s RS-232

port and the device’s RS-232 port are different

genders, use a gender changer.

7. Plug-in a DC power adapter to all transmitters

and receivers. The units power on.

8. Power on all Video Sources and start playing

video.

9. Power on all Displays/TVs and select HDMI

input. All displays/TVs show video depending

on the video channel selected.

10. To assign different video channels (sources),

use an IR Receiver cable or the 99-channel

IR remote controller on the receiver side

to switch the source channel, or change

the receiver’s video channel by using

pushbuttons on the receiver.

11. Select the video channel by using pushbuttons

(CH+/CH-) on every transmitter/receiver

based on the link mapping, and set it up

by pressing the “Set/Reset” button.

The 7-segment LED display (Video Channel)

will stop blinking when the setting

is completed.

12. To use the 99-channel IR remote controller,

see Step 5 -Remote Control on the next page.

STEP 5 - Remote Control

USING THE REMOTE CONTROL

To use the 99-channel IR remote controller,

follow steps A through C below.

A. Press “CH+” or “CH-“ to scroll to the next

or previous available video channel.

B. Press the number key “1” – “0” and “ENTER”

to directly change to the specific video channel.

C. Press “OSD” to show the status information

of the transmitter and receiver in the same

link on the top left corner of the display

connected to the receiver. The status

information includes:

Transmitter’s IP

Receiver’s IP and MAC address

Firmware version of this receiver

Device mode setting of this receiver

(Extender or Matrix)

Current receiving video channel

Current video resolution

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Black Box Empfänger Handbücher

Black Box

Black Box MediaCento UVX-HDMI-POE-RX Bedienungsanleitung

Black Box

Black Box CAT5 Shielded Twisted Pair (STP) Patch Cable Bedienungsanleitung

Black Box

Black Box AC3003A-NEC Bedienungsanleitung

Black Box

Black Box AC155A Bedienungsanleitung

Black Box

Black Box AC561A-50 Bedienungsanleitung

Black Box

Black Box IC441A-R2 Bedienungsanleitung

Black Box

Black Box ACS4001A-R2-R Bedienungsanleitung

Black Box

Black Box MediaCento VSPX-HDMI1X4-TX Bedienungsanleitung

Black Box

Black Box AC1140A Bedienungsanleitung

Black Box

Black Box VX1000 Series Bedienungsanleitung

Black Box

Black Box FiberPath AC444A Bedienungsanleitung

Black Box

Black Box ME190A Bedienungsanleitung

Black Box

Black Box Fiber Link-Transmitter Bedienungsanleitung

Black Box

Black Box IC454A Bedienungsanleitung

Black Box

Black Box ME806A Bedienungsanleitung

Black Box

Black Box MediaCento AVX-DVI-IP-TA Bedienungsanleitung

Black Box

Black Box FaxReceiver MC200A Bedienungsanleitung

Black Box

Black Box FaxReceiver MC200A Bedienungsanleitung

Black Box

Black Box AC155A-R2 Bedienungsanleitung

Black Box

Black Box AVX-VGA-TP-TX Bedienungsanleitung

Black Box

Black Box AC1063A-R2 Bedienungsanleitung

Black Box

Black Box AC155A-R3 Bedienungsanleitung

Black Box

Black Box ServSwitch Agility ACR1000A Bedienungsanleitung

Black Box

Black Box VX-1003-RX Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung