Black Box LES1202A Bedienungsanleitung

Remote Console Mana

Quick Start Guide

This Quick Start Guide helps you through installation, configuration,

and local operation. For more details, refer to the user manual .

LES1202A LES1203A-M

LES1203A-11G LES1204A-R2

Remote Console Manager Quick Start Guide

724-746-5500 | blackbox.com

Page 2

Trademarks Used in this Manual

Black Box and the Double Diamond logo are registered trademarks of

BB Technologies, Inc.

Cisco is a registered trademark of Cisco Technology, Inc.

Linux is a registered trademark of Linus Torvalds.

Nagios is a registered trademark of Nagios Enterprises.

Any other trademarks mentioned in this manual are acknowledged to be the

property of the trademark owners.

Remote Console Manager Quick Start Guide

724-746-5500 | blackbox.com Page 3

Follow the steps listed below to get started:

Step 1: Check kit contents.

LES1202A, LES1203A-M, LES1203A-11G, or LES1204A-R2 Remote

Console Manager

This printed quick start guide

(2) UTP cables

(1) DB9F-RJ-45 adapter straight-pinned

(1) DB9F-RJ-45 adapter crossover-pinned

Universal input 12-VDC power pack

CD-ROM containing SDT Connector and PortShare software

NOTE: To download the user manual, go to

ftp://ftp.blackbox.com/anonymous/manuals/L/les1202a_user_rev2.pdf, or

visit the Black Box Web site and enter LES1202A in the search bar.

Step 2: Connect the hardware.

Plug the power pack into the AC power receptacle and connect the DC

power cable to the 9-12 VDC power socket on the Remote Console

Manager.

Connect the LAN port to your network.

Connect your serial devices to the SERIAL ports. Your Remote Console

Manager has two, three, or four RJ-45 serial ports. The RJ-45 serial

connectors have Cisco® serial pinouts:



  

  

  

  

  

!  

"  

#  

$  



Figure 1. Cisco serial pinouts.

NOTE: If you have a LES1203-M and plan to use out-of-band (OoB) dial-in

access, connect the internal modem to the phone line.

Remote Console Manager Quick Start Guide

724-746-5500 | blackbox.com

Page 4

Step 3: Set up the remote console manager.

The default remote console manager IP address is 192.168.0.1 (subnet

mask 255.255.255.0). With a Web browser on any computer that is

connected through the LAN to the serial device server:

• Enter https://192.168.0.1 into the address bar.

NOTE: The LAN-connected computer must have an IP address in the same

network range (192.168.0.xxx) as the remote console manager. If this is not

convenient, you can use the ARP Ping command to set the IP address (refer

to the user manual for details). The remote console manager also has its

DHCP client enabled by default, so it will automatically accept any network

IP address assigned by any DHCP server on your network—and will then

respond at both 192.168.0.1 and its DHCP address.

Log in using the default system user name: root, and the default

password: default. A Welcome screen listing the basic configuration steps

is displayed.

Select “System: Administration,” enter and confirm a new system

password, and click “Apply.”

Figure 2. System: Administration screen.

To assign your remote console manager a static IP address or to

permanently enable DHCP, select “System: IP” then “Network Interface”

and check “DHCP” or “Static” for configuration method.

NOTE: By default, only HTTPS and SSH access is enabled to the Remote

Console Manager itself. Use Service Access menu on System: Firewall to

change this, and to change access privileges for connected serial and

network devices. Similarly, use the Forwarding & Networking menu to permit

remote IP access to devices on Network or Management LAN.

Remote Console Manager Quick Start Guide

724-746-5500 | blackbox.com Page 5

Step 4: Configure serial and network devices.

Select “Serial & Network: Serial Port,” which will display the label, mode,

and protocol options currently set for the serial port. By default, all the

serial ports, except Port 1, are set to console server mode (see the user‘s

manual for other modes).

Figure 3. Serial & Network: Serial Port screen.

To configure a serial port, click “Edit.”

Configure the common settings (baud rate, parity, data bits, stop bits, and

flow control) to match those of the serial device being controlled.

Select the console server protocols (Telnet, SSH, TCP, and RFC2217)

that will be used for the data connection to the serial port.

NOTE: Port 1 is configured by default in Local Console (modem) mode. Use

the crossover-pinned DB9F-RJ-45 adapter and UTP cable to connect to a

terminal emulator application on your PC’s serial COM port. If you plan to

use OoB dial-in access, connect this serial port to an external modem as

covered in detail in the user manual on the CD-ROM.

Click “Apply.”

To enable access through the remote console manager to a locally

networked computer (referred to as a host), select “Serial & Network:

Network Hosts” and click “Add Host.”

Remote Console Manager Quick Start Guide

724-746-5500 | blackbox.com

Page 6

Figure 4. Serial & Network: Network Hosts screen.

Enter the IP address/DNS name of the host.

Edit the permitted services used for accessing this host, for example,

HTTPS (TCP port 443), VNC (TCP port 5900), or add custom TCP or

UDP port numbers—only the services specified here are tunneled

through to the host. All other services are blocked.

Specify the level of information to be logged and monitored for each host

access.

Click “Apply.”

Step 5: Add new users.

NOTE: We recommend that you set up a new Administrator user (in the

admin group with full access privileges) and log in as this new user for all

ongoing administration functions (rather than continuing as root).

For each new user, select “Serial & Network: Users & Groups” and click

“Add User.”

Enter a username and enter and confirm a password, and nominate the

accessible hosts and accessible ports the user is allowed to access.

Remote Console Manager Quick Start Guide

724-746-5500 | blackbox.com Page 7

Figure 5. Serial & Network: Users & Groups screen.

To grant limited access to the management console, check the “User”

group. To grant full access to the management console, check the

“Admin” group. By default, the user is granted no management console

access.

Click “Apply.”

NOTE: The Remote Console Manager comes with a default certificate for

initial configuration purposes only. You will need to direct your browser to

(temporarily) proceed and accept this untrusted certificate. It is

recommended as soon as possible thereafter you generate and install a new

trusted certificate. To produce the unique CSR and later upload the newly

issued certificate, select System: SSL Certificates.

Step 6: Custom setup.



The Remote Console Manager family has various models that may require

some custom setup:

LES1203A-M has an internal modem that can be configured for dial-in

access (or dial-out failover connection) using the Internal Modem Port

tab under System: Dial menu.

LES1203A-11G comes with an internal 802.11 wireless modem that can

be configured using the Wireless LAN Interface menu in the System: IP

menu. The wireless LAN is deactivated by default and when enabled will

operate as the main network connection. Failover is available (though it is

not enabled by default).

LES1204A-3G-R2 comes with an internal 3G cellular modem— and its

own Quick Start Guide.

Remote Console Manager Quick Start Guide

724-746-5500 | blackbox.com

Page 8

Step 7: Advanced configurations.

The console server offers many more advanced functions, including:

The Alerts & Logging: Alerts facility monitors serial ports, hosts, user

logins, UPSs (uninterruptible power supplies), and RPCs (remote power

controllers such as PDUs and IPMI devices). A broad selection of trigger

events (such as data patterns, temperature, or battery levels) can be

specified. When triggered, a warning e-mail, SMS, Nagios®, or SNMP

alert is sent to a nominated destination.

Extensive management of UPSs and RPCs using Open Source NUT and

Powerman tools. The Manage: Power facility enables both administrators

and regular users to monitor and control attached PDU power strips, and

servers with embedded IPMI BMCs.

Historical logs of all communications with serial and network-attached

devices, system activity, UPS and PDU power status, environmental

status, etc. The level of logging is set as ports and devices are

configured. Alerts & Logging: Port Log allows this history to be saved

locally or remotely. Logs can be viewed from the Status and Manage

menus.

Other advanced features, such as serial port cascading, remote

authentication, trusted networks, secure tunneling, Nagios distributed

monitoring, and the command line interface are covered in detail in the

user manual.

NOTE: To download the user manual, go to

ftp://ftp.blackbox.com/anonymous/manuals/L/les1202a_user_rev2.pdf, or

visit the Black Box Web site and enter LES1202A in the search bar.

NOTE: Also on the Black Box Web site, you will find the SDT Connector

software tool. Once you have configured the console server, this tool

provides you with secure, point-and-click access to the console server and

all the attached devices. Refer to the provided SDT Connector Quick Start

for details on setting up remote management of the console server and

connected devices.

NOTE: Also on the Black Box Web site, you will also find PortShare

software, which enables applications on your Windows® or Linux®

PC/server/virtual server to control serial port devices attached to a Remote

Console Manager. To use PortShare, configure the Remote Console

Manager serial port in console server mode and specify the appropriate

protocol (either RFC2117 or RAW) to be used (see the user‘s manual for

details).

Remote Console Manager Quick Start Guide

724-746-5500 | blackbox.com Page 9

NOTES

724-746-5500 | blackbox.com

Page 10

Dieses Handbuch passt für folgende Modelle

Andere Black Box Server Handbücher

Black Box

Black Box LES301A-KIT Bedienungsanleitung

Black Box

Black Box 40870-R2 Bedienungsanleitung

Black Box

Black Box LES1208A-R2 Bedienungsanleitung

Black Box

Black Box LES1516A Bedienungsanleitung

Black Box

Black Box les1208A Bedienungsanleitung

Black Box

Black Box LES1102A Bedienungsanleitung

Black Box

Black Box LES290A Bedienungsanleitung

Black Box

Black Box LES301A-KIT Bedienungsanleitung

Black Box

Black Box LWS401A Bedienungsanleitung

Black Box

Black Box ServView II Bedienungsanleitung

Black Box

Black Box 37687 Bedienungsanleitung

Black Box

Black Box ServShield RM470A-R2 Bedienungsanleitung

Black Box

Black Box LS50116-R3 Bedienungsanleitung

Black Box

Black Box LS1016A Bedienungsanleitung

Black Box

Black Box LWS405A Bedienungsanleitung

Black Box

Black Box LS1016A Bedienungsanleitung

Black Box

Black Box LES2702A-WL Bedienungsanleitung

Black Box

Black Box LES302A Bedienungsanleitung

Black Box

Black Box ME0008A-ME1 Bedienungsanleitung

Black Box

Black Box LE995A-R4 Bedienungsanleitung

Black Box

Black Box RM5000A-R3 Bedienungsanleitung

Black Box

Black Box Industrial Ethernet Serial Server LES401A... Bedienungsanleitung

Black Box

Black Box LES4011 Bedienungsanleitung

Black Box

Black Box LWS300A Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung