Black Horse Model Harmon Rocket BH100 Betriebsanleitung

SPECIFICATION



 Wingspan : 1,660 mm 65.35 in.



 Length :



 Weight : 4.8 kg 10.56 Lbs.



 Radio : 05 channels.



 Servo : 07 servos.

Instruction Manual book

Made in Vietnam.

1,575 mm 62.01 in.



 Engine : 20 CC Gas.

ITEM CODE:BH100.

HARMON ROCKET - Item code: BH100 . Instruction Manual

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your HARMONROCKET. Use the parts listing below

to identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C supplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

procedures designed to help the new pilot on his way to successful R/C flight. They will also be able

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modelling knife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

Some more parts.

HARDWAREPACK

COWLING.

Landing gear.....

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the air-

craft and to protect the table. Keep a couple of

jars or bowls handy to hold the small parts af-

ter you open the bag.

Please trial fit all the parts. Make sure you have

the correct parts and that they fit and are

aligned properly before gluing! This will assure

proper assembly. HARMON ROCKET ARF

is hand made from natural materials, every

plane is unique and minor adjustments may

have to be made. However , you should find

the fit superior and assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the follow-

ing: paint thinner, C/A glue accelerator, C/A glue

debonder and acetone. Do not let these chemi-

cals come in contact with the colors on the

covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage.

WING ASSEMBLY

(1) Right wing half with pre-installed

aileron.

(1) Left wing half with pre-installed

aileron.

Tail section assembly

(1) Vertical stabilizer with pre-

installed rudder.

(1) Horizontal stabilizer with pre-

installed elevator halves.

SUGGESTION.

NOTE.

HARMON ROCKET - Item code: BH100 . Instruction Manual

Caution: this model is not a toy!

If you are a beginner to this type of powered

model, please ask an experienced model flyer

for help and support. If you attempt to operate

the model without knowing what you are doing

you could easily injure yourself or somebody

else. Please keep your safety and well-being

in mind at all times.

Important: before you start construction

Even if you have already built a large number

of RC models please read right through these

instructions and check all the kit components

against the parts list. We have taken great

trouble to keep construction as simple as

possible, without making any compromises

in the area of safety.

Note regarding the film covering

Minor creases or bubbles may develop in the

film covering due to major fluctuations in

weather conditions (temperature, humidity

etc.); in rare cases you may even find a slight

warp in a component. These minor faults are

in the nature of film-covered built-up wooden

structures, and can easily be corrected using

a heat gun, as commonly used for modelling.

Creases: Blow warm air over the area

and rub down with a soft

cloth.

When self-tapping screws have to be

screwed into wood, apply a little white

glue to prevent them shaking loose: just

squirt white glue into the hole and fit the

screw.

+ This is not a toy

+ Be sure that no other flyers are using your

radio frequency.

+ Do not smoke near fuel

+ Store fuel in a cool, dry place, away from

children and pets.

+ Wear safety glasses.

+The glow plug clip must be securely at-

tached to the glow plug.

+ Do not flip the propeller with your fingers.

+ Keep loose clothing and wires away from

the propeller.

+ Do not start the engine if people are near.

Do not stand in line with the side of the pro-

peller.

+ Make engine adjustments from behind the

propeller only. Do not reach around the spin-

ning propeller.

SAFETY PRECAUTION.

Wing warp: Hold the panel twisted

gently in the opposite

direction to the warp, and

apply warm air to remove

the creases from the

covering.

Caution! do not heat the film more than is

absolutely necessary. If the air or the iron is

too hot, the film may melt and holes may be

formed.

This model is highly pre-fabricated and can

be built in a very short time. However, the work

which you have to carry out is important and

must be done carefully . The model will only

be strong and fly well if you complete your

tasks competently - so please work slowly

and accurately.

REPLACEMENT LARGE PARTS

C. Fuselage.

D. Horizontal stabilizer B. Wing panel.

A. Cowling.

F. Aluminium wing dihedral brace.

E. Rudder.

G. Decal sheet .

HARMON ROCKET - Item code: BH100 . Instruction Manual

REPLACEMENT SMALL PARTS

 1. Install the rubber grommets and brass

eyelets onto the aileron servo.

INSTALLING THE AILERON SERVO.

I. SERVO

2. Drill 1,5mm pilot holes through the block

of wood for each of the four mounting screws

provided with the servo. Install servo into ai-

leron servo tray as same as picture below.

1. Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

3. Instal servo tray with aileron servo into

the wing as same as picture below.

7. Engine mount ply of wood.

2. Wheels.

3. Wheel pants.

8. Fuel Tank.

4. Tail gear set.

5. Spinner.

6. Plastic parts for rudder pushrod.

Bottom side.

2x10mm.

Electric

wire.

Thread. Aileron.

1. Aluminium landing gear.

1. 1.

6. 7.

HARMON ROCKET - Item code: BH100 . Instruction Manual

Install aileron control horn as same

as picture below.

Repeat the procedure for the other wing

half.

Repeat the procedure for the other wing

half.

Installing the aileron linkages as pictures

below.

Attach the clevis to the outer hole in the con-

trol horn.

INSTALLING THEAILERON CONTROL HORN .

INSTALLING THE AILERON

LINKAGES.

Secure.

Control horn of

the aileron.

3 x 20 mm.

2x8mm.

70 mm

Secure.

HARMON ROCKET - Item code: BH100 . Instruction Manual

Installing the aileron linkages as pictures

below.

3.INSTALLING THE FLAP

LINKAGES.

Repeat the procedure for the other wing

half.

1.INSTALLING THE FLAP SERVO

2.INSTALLING THE FLAP CONTROL HORN.

thread

Electric

way

2x10mm.

Secure.

Control horn

of the flap.

Secure.

Flap

3 x 20 mm.

2x8mm.

70 mm

3 x 20 mm.

II. FLAP

HARMON ROCKET - Item code: BH100 . Instruction Manual

INSTALLING THE ENGINE MOUNT.

See pictures below:

Drill 5mm

hole.

Secure.

INSTALLING THE ENGINE-

Secure.

Left side.

Mount ply of

wood .

3x12mm

HARMON ROCKET - Item code: BH100 . Instruction Manual

INSTALLING THE STOPPER ASSEMBLY

1) The stopper has been pre-assembled

at the factory.

2) Using a modeling knife, cut one length

of silicon fuel line (the length of silicon fuel line

is calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the stop-

per.

3) Carefully bend the second nylon tube

up at a 45 degree angle (using a cigarette

lighter). This tube will be the vent tube to the

muffler.

4) Carefully bend the third nylon tube down

at a 45 degree angle (using a cigarette lighter).

This tube will be vent tube to the fueling valve.

FUEL TANK.

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank. 9) To secure the fuel tank in place, apply a

bead of silicon sealer to the forward area of

the tank, where it exits the fuselage behind the

engine mounting box and to the rear of the tank

at the forward bulkhead.

Do not secure the tank into place perma-

nently until after balancing the airplane. You

may need to remove the tank to mount the

battery in the fuel tank compartment

5) Test fit the stopper assembly into the

tank. It may be necessary to remove some of

the flashing around the tank opening using

a modeling knife. If flashing is present, make

sure none of it falls into the tank.

6) When satisfied with the alignment of

the stopper assembly tighten the 3mm x 20mm

machine screw until the rubber stopper ex-

pands and seals the tank opening. Do not over

tighten the assembly as this could cause the

tank to split.

7) Using a modeling knife, cut 3 lengths of

fuel line 150mm long. Connect 2 lines to the 2

vent tubes and 1 line to the fuel pickup tube in

the stopper.

8) Feed three lines through the fuel tank

compartment and through the pre-drilled hole

in the firewall. Pull the lines out from behind

the engine, while guiding the fuel tank into

place. Push the fuel tank as far forward as

possible, the front of the tank should just about

touch the back of the firewall.

Blow through one of the lines to ensure

the fuel lines have not become kinked inside

the fuel t ank compartment. Air should flow

through easily.

Vent tube Fuel pick- up tube

Fuel fill tube

Tygon gas tubing not included.

HARMON ROCKET - Item code: BH100 . Instruction Manual

Secure.

Fuel tank

1. Install one adjustable metal connector

through the third hole out from the center of

one servo arm, enlarge the hole in the servo

arm using a 2mm drill bit to accommodate the

servo connector. Remove the excess mate-

rial from the arm.

After installing the adjustable metal con-

nector apply a small drop of thin C/A to

the bottom nut. This will prevent the con-

nector from loosening during flight.

INSTALLING THE THROTTLE - CABLE.

Throttle servo

Throttle cable.

HARMON ROCKET - Item code: BH100 . Instruction Manual

2) Using the hardware provided, mount

the main landing gear to the fuselage.

Bottom side.

Left side.

PARTSREQUIRED

MAIN GEAR INSTALATION.

 1) Assemble and mounting the wheel pants

as shown in the following pictures.

Mark line.

Throttle -

cable

Secure.

32.

1. 1.

Inhaltsverzeichnis

Andere Black Horse Model Spielzeug Handbücher

Black Horse Model

Black Horse Model Excel 2000 Betriebsanleitung

Black Horse Model

Black Horse Model Excel 2000 Betriebsanleitung

Black Horse Model

Black Horse Model DECATHLON-EP Betriebsanleitung

Black Horse Model

Black Horse Model Extra 260-EP BH55 Betriebsanleitung

Black Horse Model

Black Horse Model GRUNAU BABY 2B Betriebsanleitung

Black Horse Model

Black Horse Model B.A. EAGLE Betriebsanleitung

Black Horse Model

Black Horse Model Mustang P51 Bedienungsanleitung

Black Horse Model

Black Horse Model HEINKEL HE 111 Betriebsanleitung

Black Horse Model

Black Horse Model MINIMOA Betriebsanleitung

Black Horse Model

Black Horse Model Fieseler Fi156C STORCH Betriebsanleitung

Black Horse Model

Black Horse Model Blade BH 70 Betriebsanleitung

Black Horse Model

Black Horse Model L-39 Albatros Betriebsanleitung

Black Horse Model

Black Horse Model EP-TRAINER Betriebsanleitung

Black Horse Model

Black Horse Model ZLIN 50LS Betriebsanleitung

Black Horse Model

Black Horse Model BH147 Betriebsanleitung

Black Horse Model

Black Horse Model LF-107 Lunak Betriebsanleitung

Black Horse Model

Black Horse Model RENEGADE Bedienungsanleitung

Black Horse Model

Black Horse Model Spitfire 40 Bedienungsanleitung

Black Horse Model

Black Horse Model RYAN 61 Betriebsanleitung

Black Horse Model

Black Horse Model Extra S Betriebsanleitung

Black Horse Model

Black Horse Model MKII Betriebsanleitung

Black Horse Model

Black Horse Model Extra 300S Betriebsanleitung

Black Horse Model

Black Horse Model Macchi MC-200 BH 104 Betriebsanleitung

Black Horse Model

Black Horse Model Sonic Betriebsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung

REVELL

REVELL Bristol Beaufighter TF.X Bedienungsanleitung