Black Horse Model ZLIN 50LS Betriebsanleitung

SPECIFICATION

MadeinVietnam.

1Wingspan: 1,700 mm 66.93 inches.

1Length : 1,300 mm 51.18 inches.

1Weight : 3.4 kg 7.48 lbs.

1Radio : 04 channels.

1Servo : 05 servos.

1Glow Engine: 55 2 stroke; 72 4 stroke.

Parts listing required (not included).

1 Electric Motor: O.S.(OMA-5020-490).

1Battery: 5-6 Cells-Li-Poly-18.5-22.2V-5.500mAh.

1Speed control: 80A.

1Propeller: 14 x 8.

Instruction Manual Book

ITEM CODE:BH116.

ZLIN 50LS -

Item code: BH116

Instruction Manual

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manualthoroughlybeforestartingassemblyofyour ZLIN50LS.Usethepartslistingbelowtoidentify

all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedtohelpthenewpilotonhiswaytosuccessfulR/Cflight.Theywillalsobeable

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

1Thick cyanoacrylate glue.

130 minute epoxy.

15 minute epoxy.

1Hand or electric drill.

1Assorted drill bits.

1Modellingknife.

1Straightedge ruler.

12mm ball driver.

1Phillips head screwdriver.

1220 grit sandpaper.

190° square or builder’s triangle.

1Wire cutters.

1Masking tape & T-pins.

1Thread-lock.

1Paper towels.

Some more parts.

HARDWARE PACK

COWLING.

Landinggear.....

Toavoidscratching yournew airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the

aircraftandto protectthetable. Keepacouple

of jars or bowls handy to hold the small parts

after you open the bag.

Pleasetrial fitalltheparts.Makesureyouhave

the correct parts and that they fit and are

alignedproperlybefore gluing!Thiswill assure

properassembly. ZLIN 50LS ARF ishandmade

from natural materials, every plane is unique

andminoradjustmentsmay have to bemade.

However, you should find the fit superior and

assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the

following: paint thinner, C/A glue accelerator,

C/A glue debonder and acetone. Do not let

these chemicals come in contact with the

colors on the covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

1(1) Fuselage.

WING ASSEMBLY

1(1) Right wing half with pre-installed

aileron.

1(1) Left wing half with pre-installed

aileron.

Tail section assembly

1(1) Vertical stabilizer with pre-

installedrudder.

1(1) Horizontal stabilizer with pre-

installedelevator halves.

SUGGESTION.

NOTE.

ZLIN 50LS -Item code: BH116.Instruction Manual

Caution: this model is not a toy!

Ifyouarea beginner to this typeofpoweredmodel, please ask anexperiencedmodelflyerfor help

and support. If you attempt to operate the model without knowing what you are doing you could

easily injure yourself or somebody else. Please keep your safety and well-being in mind at all

times.

Important: before you start construction

Even if you have already built a large number of RC models please read right through these

instructionsandcheckallthe kit components against thepartslist.We have taken great trouble to

keep construction as simple as possible, without making any compromises in the area of safety.

Note regarding the film covering

Minor creases or bubbles may develop in the film covering due to major fluctuations in weather

conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a

component. These minor faults are in the nature of film-covered built-up wooden structures, and

can easily be corrected using a heat gun, as commonly used for modelling.

Creases: Blow warm air over the area and rub down with a soft cloth.

Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply

warm air to remove the creases from the covering.

Caution!donotheat the film more thanisabsolutelynecessary. If the air or the iron is too hot, the

film may melt and holes may be formed.

This model is highly pre-fabricated and can be built in a very short time. However, the work which

you have to carry out is important and must be done carefully. The model will only be strong and

fly well if you complete your tasks competently - so please work slowly and accurately.

When self-tapping screws have to be screwed into wood, apply a little white glue to

prevent them shaking loose: just squirt white glue into the hole and fit the screw.

+ This is not a toy

+ Be sure that no other flyers are using your radio frequency.

+ Do not smoke near fuel

+ Store fuel in a cool, dry place, away from children and pets.

+ Wear safety glasses.

+The glow plug clip must be securely attached to the glow plug.

+ Do not flip the propeller with your fingers.

+ Keep loose clothing and wires away from the propeller.

+ Do not start the engine if people are near. Do not stand in line with the side of the propeller.

+Makeengine adjustments frombehindthepropeller only.Do notreacharound the spinningpropeler.

SAFETY PRECAUTION.

F. Aluminium wing

dihedral brace.

G. Decal sheet .

A.Cowling.

B.Wing panel.

C. Fuselage

D.Horizontal stabilizer.

E. Rudder.

ZLIN 50LS -

Item code: BH116

Instruction Manual

3. Wheels.

2.Aluminium landinggear.

7. Plastic parts for elevator and rudder pushrod.

6.Spinner.

1 1. Install the rubber grommets and brass

eyelets onto the aileron servo.

4. Plastic- Engine mount.

8. Tail gear set.

5.FuelTank.

1. Wheel pants.

REPLACEMENT SMALL PARTS

I. INSTALLING THE AILERON SERVO

Aileron.

Bottom side

Aileron.

Cutthe covering

awayfromtheslot.

4x30mm.

3x20mm.

3x15mm.

5x40mm.

3x12mm

ZLIN 50LS -Item code: BH116.Instruction Manual

12)Usinga modelingknife,removethe cov-

ering at possition show below.

14.Drill1,5mmpilotholes through the block

of wood for each of the four mounting screws

provided with the servo. Install servo into ai-

leron servo tray as same as picture below.

13. Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

Electricwire

Bottomside.

Thread

Repeat the procedure for the other wing

half.

INSTALLINGTHEAILERON CONTROL HORN

Installaileron control hornassame as

picturebelow.

A+B Epoxy

PLUS glue

Temporary pin to

keep hinge centered.

Assemble then apply drops of thin

C/A to center of hinge,on both sides.

Aileron.

Bottom side

ZLIN 50LS -

Item code: BH116

Instruction Manual

Repeat the procedure for the other wing

half.

Aileron Control

horn.

11. Working with the aileron linkage for

now, thread one clevis onto one of the

threaded wires.

12. Attach the clevis to the outer hole in the

control horn. Install a silicone tube on the

clevis.

INSTALLING THE AILERON

LINKAGES.

Attach the clevis to the outer hole in the con-

trol horn.

13. Plug the aileron servo into the receiver

andcenter theservo. Installthe servoarm onto

the servo. The servo arm should be perpen-

dicular to the servo and point toward the mid-

dle of the wing.

16.Insert the90 degree bend down through

the hole in the servo arm. Install one nylon

snap keeper over the wire to secure it to the

arm.Install theservoarm retainingscrewand

remove the masking tape from the aileron.

Bend and

cut after.

14. Locate one nylon servo arm, and using

wire cutters,remove all but one of the arms.

Using a 2mm drill bit, enlarge the third hole

out from the center of the arm to accommo-

date the aileron pushrod wire.

15.Usingpliers,carefullymake a 90 degree

bend down at the mark made. Cut off the ex-

cess wire, leaving about 4mm beyond the

bend.

M2 clevis.

M2locknut. Snap keeper.

ZLIN 50LS -Item code: BH116.Instruction Manual

Repeat the procedure for the other wing

half.

THERE ARE TWO OPTIONS:

1. ELECTRIC MOTOR

2. ENGINE MOUNT.

1. OPTION 1: ELECTRIC MOTOR

INSTALLING ELECTRIC MOTOR.

Drill a hole

4mmdiameter.

Aileron servo

Aileron

Bottom side

50mm

Cut.

220 mm

Aluminium tube.

4 x 60 mm

ZLIN 50LS -

Item code: BH116

Instruction Manual

Front view.

Secure.

Motor.

Battery.

Push

Secure.

Rotor sharft.

Battery tray.

ZLIN 50LS -Item code: BH116.Instruction Manual

2. OPTION 2: ENGINE MOUNT.

11) Slide the cowl over the motor and line

up the back edge of the cowl with the marks

you made on the fuselage.

COWLING.

13) Slide the cowl back over the motor.

12) While keeping the back edge of the

cowl flush with the marks, align the front of

thecowlwiththe crankshaft of themotor. The

front of the cowl should be positioned so the

crankshaft is in nearly the middle of the cowl

opening. Hold the cowl firmly in place using

pieces of masking tape.

See pictures below:

INSTALLING THE ENGINE MOUNT.

Frontview.

Drill a hole

4mm diameter.

4x30mm

3x20mm

ZLIN 50LS -

Item code: BH116

Instruction Manual

Markpoint.

119mm

Markpoint.

Drill a hole

2mm diameter.

Secure.

3 x 20mm

Inhaltsverzeichnis

Andere Black Horse Model Spielzeug Handbücher

Black Horse Model

Black Horse Model SPEED AIR BH.08 Betriebsanleitung

Black Horse Model

Black Horse Model Sprinter Bedienungsanleitung

Black Horse Model

Black Horse Model BH172 Betriebsanleitung

Black Horse Model

Black Horse Model NOORDUYN NORSEMAN Betriebsanleitung

Black Horse Model

Black Horse Model Motion RC PIPER J-3 CUB Betriebsanleitung

Black Horse Model

Black Horse Model Liberty 182II Bedienungsanleitung

Black Horse Model

Black Horse Model Extra 300S Betriebsanleitung

Black Horse Model

Black Horse Model Excel 2000 Betriebsanleitung

Black Horse Model

Black Horse Model TURBO BEAVER BH162 Betriebsanleitung

Black Horse Model

Black Horse Model Pitts BH85-A Bedienungsanleitung

Black Horse Model

Black Horse Model SPACE WALKER Betriebsanleitung

Black Horse Model

Black Horse Model Edge 540-V3 Betriebsanleitung

Black Horse Model

Black Horse Model Thermal 3.0 Betriebsanleitung

Black Horse Model

Black Horse Model THUNDERBIRDS Betriebsanleitung

Black Horse Model

Black Horse Model BH150 Betriebsanleitung

Black Horse Model

Black Horse Model Corsair BH64 Betriebsanleitung

Black Horse Model

Black Horse Model BH175 Bedienungsanleitung

Black Horse Model

Black Horse Model BH36-A Betriebsanleitung

Black Horse Model

Black Horse Model Mustang P51 Bedienungsanleitung

Black Horse Model

Black Horse Model Spitfire MK Betriebsanleitung

Black Horse Model

Black Horse Model AT.6-Texan Betriebsanleitung

Black Horse Model

Black Horse Model BH48 Betriebsanleitung

Black Horse Model

Black Horse Model Fieseler Fi156C STORCH Bedienungsanleitung

Black Horse Model

Black Horse Model sea fury-ep Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung

REVELL

REVELL Bristol Beaufighter TF.X Bedienungsanleitung