Black Horse Model Travel Air Betriebsanleitung

SPECIFICATION



 Wingspan : 1,550 mm 61.02 in.



 Length : 1,250 mm 49.2 in.



 Weight : 2.4 kg 5.28 Lbs.



 Radio : 04 channels.



 Servo : 05 servos.



 Engine : 40 - 46 2 stroke

52 4 stroke

Instruction Manual book

Made in Vietnam.

TRAVEL AIR-Item code:BH06. Instruction Manual

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your TRAVEL AIR. Use the parts listing below to

identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C supplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

procedures designed to help the new pilot on his way to successful R/C flight. They will also be able

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modelling knife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

Some more parts.

HARDWAREPACK

Landing gear.....

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the air-

craft and to protect the table. Keep a couple of

jars or bowls handy to hold the small parts af-

ter you open the bag.

Please trial fit all the parts. Make sure you have

the correct parts and that they fit and are

aligned properly before gluing! This will assure

proper assembly. TRAVEL AIR ARF is hand

made from natural materials, every plane is

unique and minor adjustments may have to

be made. However, you should find the fit su-

perior and assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the follow-

ing: paint thinner, C/A glue accelerator, C/A glue

debonder and acetone. Do not let these chemi-

cals come in contact with the colors on the

covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage.

WING ASSEMBLY

(1) Right wing half with pre-installed

aileron.

(1) Left wing half with pre-installed

aileron.

Tail section assembly

(1) Vertical stabilizer with pre-

installed rudder.

(1) Horizontal stabilizer with pre-

installed elevator halves.

SUGGESTION.

NOTE.

TRAVEL AIR-Item code:BH06. Instruction Manual

+ This is not a toy

+ Be sure that no other flyers are using your

radio frequency.

+ Do not smoke near fuel

+ Store fuel in a cool, dry place, away from

children and pets.

+ Wear safety glasses.

+The glow plug clip must be securely attached

to the glow plug.

+ Do not flip the propeller with your fingers.

+ Keep loose clothing and wires away from

the propeller.

+ Do not start the engine if people are near.

Do not stand in line with the side of the propel-

ler.

+ Make engine adjustments from behind the

propeller only. Do not reach around the spin-

ning propeller.

Caution: this model is not a toy!

If you are a beginner to this type of powered

model, please ask an experienced model flyer

for help and support. If you attempt to operate

the model without knowing what you are doing

you could easily injure yourself or somebody

else. Please keep your safety and well-being

in mind at all times.

Important: before you start construction

Even if you have already built a large number

of RC models please read right through these

instructions and check all the kit components

against the parts list. We have taken great

trouble to keep construction as simple as

possible, without making any compromises

in the area of safety.

Note regarding the film covering

Minor creases or bubbles may develop in the

film covering due to major fluctuations in

weather conditions (temperature, humidity

etc.); in rare cases you may even find a slight

warp in a component. These minor faults are

in the nature of film-covered built-up wooden

structures, and can easily be corrected using

a heat gun, as commonly used for modelling.

Caution! do not heat the film more than is

absolutely necessary. If the air or the iron is

too hot, the film may melt and holes may be

formed.

This model is highly pre-fabricated and can

be built in a very short time. However, the work

which you have to carry out is important and

must be done carefully . The model will only

be strong and fly well if you complete your

tasks competently - so please work slowly and

accurately.

When self-tapping screws have to be

screwed into wood, apply a little white glue

to prevent them shaking loose: just squirt

white glue into the hole and fit the screw.

Creases: Blow warm air over the area

and rub down with a soft

cloth.

SAFETY PRECAUTION.

Wing warp: Hold the panel twisted gently

in the opposite direction to

the warp, and apply warm

air to remove the creases

from the covering.

REPLACEMENT LARGE PARTS

3.Horizontal stabilizer

2.Wings panel(Left $ Right).

1. Fuselage.

5. Aluminium tube wing

4. Vertical stabilizer

TRAVEL AIR-Item code:BH06. Instruction Manual

 1. Install the rubber grommets and brass

eyelets onto the aileron servo.

Top side.

Bottom side.

aileron.

REPLACEMENT SMALL PARTS

5. Plastic parts for elevator and rudder pushrod.

7. Spinner.

2. Fuel Tank.

6. Tail gear

3. Wheels.

4.Tie wrap

3x12mm.

5x35mm.

3x12mm.

INSTALLING THEAILERON SERVOS.

1. Aluminium landing gear.

TRAVEL AIR-Item code:BH06. Instruction Manual

2. Using a modeling knife, remove the cov-

ering servo tray.

Servo tray.

3. Drill 1,5mm pilot holes through the block

of wood for each of the four mounting screws

provided with the servo. Install servo into ai-

leron servo tray as same as picture below.

Secure.

4. Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

Temporary pin to

keep hinge centered.

Assemble then apply drops of thin

C/A to center of hinge,on both sides.

Cut the covering

away from the slot.

TRAVEL AIR-Item code:BH06. Instruction Manual

Repeat the procedure for the other wing

half.

2. Drill through 1.5mm (diameter) the ai-

leron using the control horn as a guide and

screw the control horn in place.

Bottom side.

Drill a

hole

1.5mm

5. Instal servo tray with aileron servo into

the wing as same as picture below.

Electric wire.

Servo tray.

Wing.

2x10mm.

1. Using a ruler & pen to draw a straight

line as below picture.

INSTALLINGTHEAILERON CONTROLHORN.

Install aileron control horn as same

as picture below.

Control horn of Aileron

Mark line.

2 x20mm.

TRAVEL AIR-Item code:BH06. Instruction Manual

Secure

Control horn

of Aileron

1. Working with the aileron linkage for

now, thread one clevis onto one of the

threaded wires.

2. Attach the clevis to the outer hole in the

control horn. Install a silicone tube on the

clevis.

3. Plug the aileron servo into the receiver

and center the servo. Install the servo arm onto

the servo. The servo arm should be perpen-

dicular to the servo and point toward the mid-

dle of the wing.

4. Locate one nylon servo arm, and using

wire cutters,remove all but one of the arms.

Using a 2mm drill bit, enlarge the third hole

out from the center of the arm to accommo-

date the aileron pushrod wire.

5. Using pliers, carefully make a 90 degree

bend down at the mark made. Cut off the ex-

cess wire, leaving about 4mm beyond the

bend.

6. Insert the 90 degree bend down through

the hole in the servo arm. Install one nylon

snap keeper over the wire to secure it to the

arm. Install the servo arm retaining screw and

remove the masking tape from the aileron.

Bend and

cut after.

M2 clevis.

Snap keeper.

Repeat the procedure for the other wing

half.

INSTALLING THE AILERON

LINKAGES.

TRAVEL AIR-Item code:BH06. Instruction Manual

INSTALLING THE ENGINE MOUNT.

Locate the long piece of wire used for the

throttle pushrod. One end of the wire has been

pre-bend in to a “Z” bend at the factory . This

“Z” bend should be inserted into the throttle

arm of the engine when the engine is fitted onto

the engine mount. Fit the engine to the engine

mount using the screws provided.

INSTALLING THE ENGINE.

3x 20mm

Secure.

Mark point.

Drill a hole 2.5mm

diameter.

TRAVEL AIR-Item code:BH06. Instruction Manual

INSTALLING THE STOPPER ASSEMBLY

1. The stopper has been pre-assembled at

the factory.

2. Using a modeling knife, cut one length of

silicon fuel line (the length of silicon fuel line is

calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the stop-

per.

3. Carefully bend the second nylon tube up

at a 45 degree angle (using a cigarette lighter).

This tube will be the vent tube to the muffler.

4. Carefully bend the third nylon tube down

at a 45 degree angle (using a cigarette lighter).

This tube will be vent tube to the fueling valve.

FUEL TANK.

When the stopper assembly is installed

in the tank, the top of the vent tube should

rest just below the top surface of the tank.

It should not touch the top of the tank.

5. Test fit the stopper assembly into the

tank. It may be necessary to remove some of

the flashing around the tank opening using

a modeling knife. If flashing is present, make

sure none of it falls into the tank.

6. When satisfied with the alignment of the

stopper assembly tighten the 3mm x 20mm

machine screw until the rubber stopper ex-

pands and seals the tank opening. Do not over

tighten the assembly as this could cause the

tank to split.

7. Using a modeling knife, cut 3 lengths of

fuel line 150mm long. Connect 2 lines to the 2

vent tubes and 1 line to the fuel pickup tube in

the stopper.

Silicon not

included.

TRAVEL AIR-Item code:BH06. Instruction Manual

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole

in the firewall. Pull the lines out from behind

the engine, while guiding the fuel tank into

place. Push the fuel tank as far forward as

possible, the front of the tank should just about

touch the back of the firewall.

Blow through one of the lines to ensure

the fuel lines have not become kinked inside

the fuel t ank comp artment. Air should flow

through easily.

9. To secure the fuel tank in place, apply a

bead of silicon sealer to the forward area of

the tank, where it exits the fuselage behind the

engine mounting box and to the rear of the tank

at the forward bulkhead.

Do not secure the tank into place perma-

nently until after balancing the airplane.

You may need to remove the tank to mount

the battery in the fuel tank compartment.

Secure.

Fuel tank.

Tie wrap

1. Install one adjustable metal connector

through the third hole out from the center of

one servo arm, enlarge the hole in the servo

arm using a 2mm drill bit to accommodate the

servo connector. Remove the excess mate-

rial from the arm.

INSTALLING THE THROTTLE SERVO.

Tie wrap.

Inhaltsverzeichnis

Andere Black Horse Model Spielzeug Handbücher

Black Horse Model

Black Horse Model RYAN BH 72 Betriebsanleitung

Black Horse Model

Black Horse Model BH129 Bedienungsanleitung

Black Horse Model

Black Horse Model GLASAIR Betriebsanleitung

Black Horse Model

Black Horse Model Space Walker BH65 Betriebsanleitung

Black Horse Model

Black Horse Model Mosquito MK VI Bedienungsanleitung

Black Horse Model

Black Horse Model L-39 Albatros Betriebsanleitung

Black Horse Model

Black Horse Model Travel Air BH.06 Betriebsanleitung

Black Horse Model

Black Horse Model L-39 Albatros Betriebsanleitung

Black Horse Model

Black Horse Model Tornado BH17 Betriebsanleitung

Black Horse Model

Black Horse Model BH58 Betriebsanleitung

Black Horse Model

Black Horse Model Sprinter Bedienungsanleitung

Black Horse Model

Black Horse Model Arrow 3D Betriebsanleitung

Black Horse Model

Black Horse Model Thermal 3.0 Betriebsanleitung

Black Horse Model

Black Horse Model GIL MORE Betriebsanleitung

Black Horse Model

Black Horse Model L-39 Albatros Betriebsanleitung

Black Horse Model

Black Horse Model GLASAIR Betriebsanleitung

Black Horse Model

Black Horse Model Impulse 100TD Bedienungsanleitung

Black Horse Model

Black Horse Model TAYLORCRAFT BH 134 Bedienungsanleitung

Black Horse Model

Black Horse Model B.A.EAGLE bh158 Bedienungsanleitung

Black Horse Model

Black Horse Model BH175 Bedienungsanleitung

Black Horse Model

Black Horse Model Westland Lysander Betriebsanleitung

Black Horse Model

Black Horse Model BH129 Bedienungsanleitung

Black Horse Model

Black Horse Model Arrow 3D Betriebsanleitung

Black Horse Model

Black Horse Model Viper Jet MKII Betriebsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung

REVELL

REVELL Bristol Beaufighter TF.X Bedienungsanleitung