BLAUBERG Sileo Design V2 Bedienungsanleitung

USER’S MENUAL

Sileo Design V2

AXIAL FAN

CONTENTS

Delivery set ............................................................................................................................................................................................................................................ 6

Brief description ................................................................................................................................................................................................................................. 6

Fan options............................................................................................................................................................................................................................................. 6

Operation guidelines ....................................................................................................................................................................................................................... 6

Designation key................................................................................................................................................................................................................................... 7

Installation and set-up..................................................................................................................................................................................................................... 7

Operation indication ....................................................................................................................................................................................................................... 8

Fan setup ................................................................................................................................................................................................................................................ 8

Technical maintenance................................................................................................................................................................................................................... 10

Storage and transportation regulations............................................................................................................................................................................... 10

Manufacturer’s warranty................................................................................................................................................................................................................ 11

This user’s manual is the primary operating document intended for technical, maintenance and operations staﬀ.

The manual contains information about purpose, technical details, operating principle, design, and installation of the

Sileo Design V2 unit and all its modiﬁcations. Technical and maintenance staﬀ must have proper theoretical knowledge and

practical training speciﬁc to ventilation systems as well as the necessary skills to carry out the work in accordance with labour

safety and construction regulations and standards applicable in the respective territory.

The information provided in the present document is true as at the document preparation. Due to the continuous product

development the company reserves the right to update the technical speciﬁcations, design or delivery package of its

products.

No part of the present publication may be reproduced, uploaded or saved in reference-providing information systems or

translated into other languages in any form whatsoever without the Company’s prior written consent.

READ THE USER’S MANUAL CAREFULLY BEFORE PROCEEDING WITH INSTALLATION WORKS.

COMPLIANCE WITH THE MANUAL REQUIREMENTS ENSURES RELIABLE OPERATION AND LONG

SERVICE LIFE OF THE UNIT.

KEEP THE USER’S MANUAL AVAILABLE AS LONG AS YOU USE THE UNIT. YOU MAY NEED TO RE-

READ THE INFORMATION ON THE PRODUCT SERVICING.

BLAUBERG VENTILATOREN GmbH is happy to oer you a new innovation product, the Sileo Design V2 fan.

The solid team of high-qualied professionals with many years of working experience, technological innovations

in design and production, high-quality components and materials from the top worldwide producers have

become the precondition for the best fans in theirs class.

Blauberg fans are the combination of innovations, energy-ecient and low-noise operation.

FOLLOW THE USER’S MANUAL REQUIREMENTS TO ENSURE DURABLE AND

TROUBLE-FREE OPERATION OF THE UNIT.

Disconnect the unit from power supply prior to any connection, servicing, maintenance, and repair

operations.

Only qualied electricians with a work permit for electrical units up to 1000 V are allowed

for installation and maintenance. The present user’s manual should be carefully read

before beginning works.

• Single-phase power mains must comply with the acting local electrical norms and standards.

• Fixed electrical wiring must be equipped with an automatic circuit breaker.

• The unit must be connected to power mains through a QF automatic circuit breaker integrated

into the ﬁxed wiring system. The gap between the circuit breaker contacts on all poles must be

not less than 3 mm. Check the unit for any visible damages of the impeller and the casing before

starting installation. The casing internals must be free of any foreign objects that can damage the

impeller blades.

• While mounting the unit, avoid compression of the casing! Deformation of the casing may result

in the motor jam and noisy operation. Misuse of the unit and any unauthorised modiﬁcations are

not allowed.

• Take steps to prevent ingress of smoke, carbon monoxide, and other combustion products into

the room through open chimney ﬂues or other ﬁre-protection devices. Suﬃcient air supply must

be provided for proper combustion and exhaust of gases through the chimney of fuel burning

equipment to prevent back drafting. Transported air must not contain any dust or other solid

impurities, sticky substances, or ﬁbrous materials.

• Do not use the unit in a hazardous or explosive environment containing spirits, gasoline,

insecticides, etc.

• Do not close or block the intake or extract vents in order to ensure the eﬃcient air ﬂow.

• Do not sit on the unit and do not put objects on it.

• The unit is allowed to be used by children aged from 8 years old and above and persons with

reduced physical, sensory, or mental capabilities or no experience and knowledge provided that

they have been given supervision or instruction regarding safe use of the unit and understand

the risks involved.

• Do not allow children to play with the unit.

THE PRODUCT MUST BE DISPOSED SEPARATELY AT THE END OF ITS SERVICE LIFE.

DO NOT DISPOSE THE UNIT AS UNSORTED MUNICIPAL WASTE.

DELIVERY SET

Fan : 1 pc.

Screws and dowels : 4 pcs.

Plastic screwdriver (only for the models with a timer) : 1 pc.

User’s manual : 1 pc.

Packing box : 1 pc.

FAN OPTIONS

Sileo Design V2 S: the fan is equipped with a built-in pull cord switch.

Sileo Design V2 T: the fan is equipped with a turn-oﬀ delay timer and an interval timer.

Sileo Design V2 H :the fan is equipped with a turn-oﬀ delay timer and a humidity sensor.

Sileo Design V2 SТ : the fan is equipped with a turn-oﬀ delay timer, an internal timer and a humidity sensor.

Sileo Design V2 SH :the fan is equipped with a built-in pull cord switch, a turn-oﬀ delay timer and a humidity sensor.

BRIEF DESCRIPTION

The products described herein is an axial fan for exhaust ventilation of small to medium-sized premises heated during winter.

The fan is designed for connection to 100 mm air ducts. The fan is equipped with a two-speed motor. The fan with a back

valve to prevent back air ﬂow during the fan standby.

OPERATION GUIDELINES

The fan is rated for connection to AC single-phase 220…240 V / 50 Hz. The air ﬂow direction in the system is shown with a

pointer on the fan casing. Ingress protection rating against access to hazardous parts and water ingress is IP45. The fan is

rated for operation at the ambient air temperature from +1 °C up to +45 °C. The fan requires no grounding.

INSTALLATION AND SET-UP

The fan is designed for ceiling or wall mounting and connection to a ventilation shaft or a round air duct of a matching

diameter (Fig. 2).

Fan installation with direct air discharge upwards is not allowed (Fig. 2).

Mounting steps:

Step 1. Cut oﬀ power supply and make sure that the power is disconnected (Fig. 3).

Step 2. Route the power cable to the vent (Fig. 4).

Step 3. Disconnect the front panel from the fan. Then remove the cover that covers the control board (Fig. 5).

Step 4. Mark and bore the fastening holes and install the fan (Fig. 6-8).

Step 5. Connect the fan to power supply in compliance with the wiring diagram (Fig. 12-16).

Step 6. Install the front panel (Fig. 9) and the decorative panel, ( Fig. 10) on the fan casing.

Step 7. Provide power supply to the fan (Fig. 11).

Designation of the terminals on the wiring diagrams:

L : live

N : neutral

LT : control circuit for fan speed or timer control (for the fans

with a timer)

S1 : external switch

S2 : speed switch

QF : circuit breaker

DESIGNATION KEY

Sileo Design V2 100 X

Variants:

S: pull cord switch;

T: turn-oﬀ delay timer ;

H: turn-oﬀ delay timer and humidity sensor ;

ST: pull cord switch and turn-oﬀ delay timer;

SH : pull cord switch, turn-oﬀ delay timer and a humidity sensor.

Exhaust spigot diameter [mm]

Duo: double-sped motor

OPERATION INDICATION

The light indicator blinks green once in 5 seconds: the fan operates with minimum speed in standby mode.

The light indicator blinks green once in a second: the turn-on delay time is activated (60 seconds).

The light indicator glows red: the humidity sensor is activated and the fan runs with the high speed.

The light indicator glows green: the switch is ON and the fan runs with the high speed.

The light indicator blinks green and red once in 1 second: the turn-oﬀ delay timer is activated.

Light indicator

FAN SETUP

: to adjust the humidity set point turn the control knob H clockwise to increase and counter-clockwise to decrease the

humidity sensor set point, adjustable from 60% up to 90%.

: turning of the interval timer on and its adjustment is performed with the potentiometer Ti.To turn the interval timer

oﬀ set the potentiometer Tiinto the leftmost position. Rotation of the potentiometer for 1/3 clockwise sets the interval timer

operation for 6 hours, rotation of the potentiometer for 2/3 clockwise sets the interval timer operation for 12 hours, rotation

of the potentiometer clockwise in the rightmost position sets the interval timer operation for 24 hours.

: to adjust the fan turn-oﬀ delay time, turn the control knob Toﬀ clockwise to increase and counter-clockwise to

decrease the turn-oﬀ delay time respectively, adjustable from 2 up to 30 minutes.

DO NOT USE A METAL SCREWDRIVER, KNIFE, ETC. FOR ADJUSTMENT

OPERATIONS NOT TO DAMAGE THE CIRCUIT BOARD.

60% 90%

To

2 min 30 min

O 24 hour

for H/SH

for T/ST

for Т/H/ST/SH

Warning! If the switch is turned OFF or the indoor humidity falls below the set point within 60 seconds after

activation of the switch or the humidity sensor, the fan continues operation with the low speed.

The fan delivery set includes a specially designed plastic

screwdriver for fan settings adjustments. Use it for setting the

on-delay time, oﬀ-delay time and humidity set point.

TECHNICAL MAINTENANCE

The fan maintenance periodicity is at least once per 6 months.

Maintenance steps:

• Cut oﬀ power supply to the fan and make that the power is disconnected (Fig. 17).

• Take oﬀ the front panel and clean the fan with a soft dry cloth or a brush (Fig. 18).

• Rinse the front panel with running water (Fig. 19).

• Wipe the fan surfaces dry.

• Cover the fan with the front panel.

• Provide power supply (Fig. 20).

WARNING! Avoid water dripping on the electric components.

• Store the unit in the manufacturer’s original packaging box in a dry closed ventilated premise with temperature range

from +5 ˚C to +40 ˚C and relative humidity up to 70 %.

• Storage environment must not contain aggressive vapours and chemical mixtures provoking corrosion, insulation, and

sealing deformation.

• Use suitable hoist machinery for handling and storage operations to prevent possible damage to the unit.

• Follow the handling requirements applicable for the particular type of cargo.

• The unit can be carried in the original packaging by any mode of transport provided proper protection against precipitation

and mechanical damage. The unit can be transported only in the working position.

• Avoid sharp blows, scratches, or rough handling during loading and unloading.

• Prior to the initial power-up after transportation at low temperatures allow the unit to warm up at room temperature for

at least 3-4 hours.

STORAGE AND TRANSPORTATION REGULATIONS

Inhaltsverzeichnis

Andere BLAUBERG Lüfter Handbücher

BLAUBERG

BLAUBERG Extero Series Bedienungsanleitung

BLAUBERG

BLAUBERG BLABBRAVO Bedienungsanleitung

BLAUBERG

BLAUBERG Auto Revers series Bedienungsanleitung

BLAUBERG

BLAUBERG KOMFORT EC DBW 550 Bedienungsanleitung

BLAUBERG

BLAUBERG BLABDUCTO Bedienungsanleitung

BLAUBERG

BLAUBERG Calm Betriebsanleitung

BLAUBERG

BLAUBERG BLAUBOX ME Series Bedienungsanleitung

BLAUBERG

BLAUBERG KOMFORT L350 Installationshandbuch

BLAUBERG

BLAUBERG Kamin 125 Installationshandbuch

BLAUBERG

BLAUBERG SMART Original Betriebsanleitung

BLAUBERG

BLAUBERG TOWER-V Series Bedienungsanleitung

BLAUBERG

BLAUBERG BlauFast Bedienungsanleitung

BLAUBERG

BLAUBERG Axis-P Bedienungsanleitung

BLAUBERG

BLAUBERG BRAVO Bedienungsanleitung

BLAUBERG

BLAUBERG BLABAERO Bedienungsanleitung

BLAUBERG

BLAUBERG VENTO Expert A50-1 Pro Bedienungsanleitung

BLAUBERG

BLAUBERG Auto Betriebsanleitung

BLAUBERG

BLAUBERG Sileo V2 Bedienungsanleitung

BLAUBERG

BLAUBERG Lux 100 Betriebsanleitung

BLAUBERG

BLAUBERG TwinBox EC 150 Bedienungsanleitung

BLAUBERG

BLAUBERG Smart Wi-Fi Bedienungsanleitung

BLAUBERG

BLAUBERG Axis-Jet Series Bedienungsanleitung

BLAUBERG

BLAUBERG VENTO Expert A50C3-1 S8 W V.2 Bedienungsanleitung

BLAUBERG

BLAUBERG Axis series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung