Download the free wBox application. If you have an Android mobile
device, you will nd the application in the Play Store. For iOS devices
the application is in the App Store.
By using your mobile phone or tablet, connect it to the device
wireless network. To do this, enter to your smartphone or tablet
settings, then go to setting of the WiFi network and nd the
network name „tempSensor_PRO-xxxxxxxxxx” where xxxxxxxxxx is
the serial number of the device. Connect to this network.
Open the wBox application. A device will appear at the top of the
screen. To add it to the application, click on "+" on the right side of
the name. To precongure the controller, click on the default device
name.
You can disable the individual sensor display on the main screen by
setting the "Sensor on" option to "No". In the "Name" eld, set a
friendly name for the sensor, eg. "air temperature".
The "Probe" table displays a list of found probes with the current
temperature values. To recognize the probes heat one of them e.g.
by holding it in your hand. Refresh the temperature readings by
pressing the button with two arrows .Select from the list the probe
you want to assign to the given sensor.
The "Temperature value shift" option allows to correct the tempera-
ture reading from the probe by a constant value. Settings can be
made with a slider or by lling a value in the eld. This option is
useful in case of unusual probe installation when it turns out that
the probe lowers or increases the real temperature. Default: 0°C.
Conrm the settings by clicking the "Save" button just below.
The controller allows you to send control commands to other
controllers of the wBox series through the home WiFi network,
through the so-called API, which allows you to build eg. a tempera-
ture control system.
When editing actions, select "Control other device" as the "Action
type", select "Temperature higher than" or "Temperature lower
than" as the "Trigger". In the "Trigger parameter" eld, enter the
temperature limit value, expressed in degrees Celsius, by which,
after being reached, the action will be triggered, e.g. "20". Selecting
the "Do not trigger more often than" option will trigger the action at
every specic time, set in the "Value in minutes" eld, throughout
the period of the exceeded value.
Click on the "Select device" button. The controller will search the
network for compatible devices and display them in a list. Select the
device you want to control and click the "Select" button. If the
device is not listed you must use the general API control method
described further.
Then in the "Call API" eld enter the API command that the driver
will call.
The most popular API commands for switchBox and shutterBox are
presented below. It was assumed that the IP address of the device
which will be controlled is: 192.168.1.123
Switching on the radiator via switchBox: http://192.168.1.123/s/1
Switching o the radiator via switchBox: http://192.168.1.123/s/0
Opening the roller shutter via shutterBox: http://192.168.1.123/s/u
Closing the roller shutter via shutterBox: http://192.168.1.123/s/d
If the device was not on the found list or you want to control another
device in the network, select "Call URL" as "Action type".
In the "URL" eld, enter the API command preceded by the http
protocol prex and the IP address of the wBox device which will be
controlled. The IP address can be found in the device settings.
Caution! All the controllers must be in the same subnet, usually the
subnet of a home router.
Conrm the entry with the "Save" button.
The main screen of the controller shows the current temperature
readings from individual probes, below there is a trend indicator for
its changes.
Historical measurement data is available by clicking on the diagram
icon in the upper right corner of the screen which is displayed only
when the device has access to the Internet - the data are stored only
on the BleBox server.
Historical measurement data can be exported for further analysis.
The export form will be displayed after clicking on the cloud icon in
the upper right corner of the screen.
Go to the conguration ("Settings" icon in the upper right corner of
the screen). In the "Main conguration" section, you can change the
name of the device that is displayed in the wBox application. The
"Status LED enabled" option allows you to turn o the built-in LED
on the device.
To communicate with the device from outside the local Wi-Fi
network, from anyplace in the world, through the wBox application,
the option "Enable remote access" must be set to "Yes". Selecting
the option "Yes" also means accepting to send measurement data to
blebox.eu server in order to process them and archive them togeth-
er with the location. Setting this option to "No", will cause no access
to the controller from outside the internal network or access to the
historical data; it will only be possible to obtain a visualization of the
current values.
Setting the "Enable event log" option to "Yes" will cause the device
to record events (e.g. sending the notication set in the "Actions"
section) in the BleBox cloud system. This allows the history of the
events to be viewed later also when the controller is oine.
In the "Sensors" section, you can congure the temperature probes
connected to the device. The probes are detected automatically
after the rst power connection and assigned, based on identiers,
to individual tabs that represent a given sensor (or rather its place of
installation, e.g. water temperature, air temperature, etc.). Further
conguration is carried out independently for each of the connect-
ed probes, on individual tabs.
ACTIONS / TEMPERATURE REGULATOR
FIRST START
MEASURING DATA
MEASURING DATA
The temperature regulator requires a hysteresis
conguration, it means, a certain dierence
between the switch on temperature and the switch
o temperature. In the case of the radiator control,
the switch on temperature must be lower than the
switch o temperature, e.g. "Temperature lower
than: 19°C, action: turn on", "Temperature higher
than 21°C, action: turn o".
You can also set the conguration using the web
browser of your phone / tablet. After connecting to
the wireless network of the controller, turn on the
browser and go website www.blebox.eu
