Blu Stream MX44VW Bedienungsanleitung

MX44VW

User Manual

MX44VW USER MANUAL

www.blustream.co.uk

Surge protection device

recommended

This product contains sensitive electri-

cal components that may be damaged

by electrical spikes, surges, electric

shock, lightning strikes, etc. Use of

surge protection systems is highly

recommended in order to protect and

extend the life of your equipment.

Safety And

Performance Notice

Do not substitute or use any other

power supply other than the enclosed

unit, or a Blustream approved replace-

ment.

Do not disassemble Blustream units

for any reason. Doing so will void the

manufacturer’s warranty.

Contents

Thank you for purchasing

this product.

For optimum performance and safety,

please read these instructions care-

fully before connecting, operating or

adjusting this product. Please keep this

manual for future reference.

Introduction 03

Features 03

Panel Descriptions 04

Control Ports 05

Matrix Front Panel - Turning On/O Outputs 06

Matrix Front Panel - EDID Management 06

Matrix Front Panel - Video Input Selection 07

Matrix Front Panel - Matrix Mode 07

Matrix Front Panel - Video Wall Mode 08-09

Matrix Front Panel - Multi-View Mode 10-11

Infrared Distribution 12

Infrared Remote Control 13

EDID Control 14

Application Diagram 15

Specifications 16

Package Contents 16

Maintenance 16

RS-232 and Telnet Commands 17-18

Infrared Commands 19-20

Web Browser Interface 21

PC Configuration Soware 21

contact [email protected]o.uk / support@blustream.com.au

MX44VW USER MANUAL

Our MX44VW HDMI/VGA matrix is a multi-purpose high-speed video processing system.

The MX44VW can be configured for 3 dierent output modes. The MX44VW can perform

as a 4x4 seamless matrix switcher, as a 2x2, 4x1 or 1x4 video wall solution and as a quad

multi-view presentation system.

Inputs can be assigned as either HDMI or VGA with associated L/R analogue audio with

control of the switcher via the front-panel push buttons, IR remote control, RS-232

interface, TCP/IP and Web GUI interface.

Introduction

FEATURES:

• Features 3 operational modes:

- 4x4 Matrix (selected HDMI or VGA inputs)

- Video wall (2x2, 4x1 or 1x4 configuration)

- Multi-viewer mode

• Features 4x video inputs that can be configured as HDMI video or VGA video with associated L/R analogue audio

• Seamless video switching

• Video inputs support all industry standard video resolutions including VGA-WUXGA (up to 1920x1200 @60Hz) and 480i-4K (3840

x 2160 @30Hz 4:4:4, 4096 x 2160 @24Hz 4:4:4)

• HDMI output resolution fixed to 1080p 60Hz

• Maximum PCM 7.1 96 KHz audio input, PCM 2CH 96KHz audio output.

• IR routing

• Supplied with Blustream IR receivers and emitters

• Control via front panel, IR, RS-232 and TCP/IP

• Web Interface Module for control and configuration of the Matrix

• 3rd Party drivers available for all major home control brands

• Advanced EDID management

• HDCP compliant

MX44VW USER MANUAL

www.blustream.co.uk

Rear Panel

1 2 3

108 9765

Front Panel

12 3 4 5 6 7 8 9

191817

151413

1LCD display – Shows the status of

input/output selection, EDID etc.

2IR receiver window.

3Power LED indicator.

4Power button – Press to power On/

O the Matrix.

5Matrix mode button - Press to

activate Matrix mode.

6Video-Wall mode button - Press to

activate Video-Wall mode.

7Multi-View mode button - Press to

activate Multi-View mode.

8HDMI output selection button 1 to

4 - To select the output from 1 to 4.

9All button for HDMI outputs – All

outputs will work as one (Selects all

outputs).

qMenu button – Press to enter EDID

set mode (see page 5).

wUp selection button - Press to

change segment’s value.

eESC – Press to quit EDID set mode.

rLock indicator.

tLock button – Press to lock the

buttons of the front panel.

yHDMI input selection button - Press

to individually change inputs 1-4 to

HDMI.

uVGA input selection button - Press

to individually change inputs 1-4 to

VGA.

iInput selection button 1 to 4 – Press

to select the input from 1 to 4.

oSelection button – Press to select

current setting.

pDown selection button – Press to

change segment’s value.

aEnter button – Press to confirm

mode selection or set EDID to

specified INPUT or copy EDID from

specified OUTPUT to specified

INPUT.

1IR inputs – 3.5mm stereo jack.

Routes IR to the current source

selected IR output. When using the

IRCAB cable ensure cable direction

is correct.

2IR outputs – 3.5mm mono jack

– Source specific routed IR. Use

supplied Blustream 5V IR emitters.

3VGA inputs with associated 3.5mm

L/R Analogue audio – Connect to

VGA sources.

NOTE: Either HDMI OR VGA signal

type must be assigned per source

input. Both video inputs cannot be

active at the same time.

4TCP/IP (RJ45) – Connect to LAN for

TCP/IP control of Matrix or control by

built-in Web-GUI interface.

5RS-232 port – For control of the

Matrix switcher from PC or control

processer.

6HDMI output – Connect to HDMI

displays.

7HDMI inputs – Connect to HDMI

sources.

8HDMI active connection LED - Lit

when active HDMI connection is

connected.

9IR input for matrix control – For hard

wired IR connection. Connect to

control processor or Blustream 5v IR

receiver.

qPower port – Use supplied 12V 3A

DC adaptor to power.

wPower switch - Turn Matrix On/O

10 11 12

contact [email protected]o.uk / support@blustream.com.au

MX44VW USER MANUAL

The MX44VW main communication ports are located on the rear panel and includes the following connections:-

Connections:

A. IR Input (3.5mm stereo jack) for routed IR pass-through to the associated

source output emitters.

B. IR Output (3.5mm mono jack) for routed IR control of source equipment*

C. TCP/IP – For control of the Matrix (RJ45 Connector)

D. RS-232 – For control of the Matrix (9 pin serial connection)

E. Global IR Input 3.5mm stereo jack - For control of the Matrix Switcher*

*Note - Blustream products use 5V IR hardware. For further details please see

page 12 ‘Infrared Distribution’

Blustream MX44VW Matrix is supplied with all required 5V IR emitters and

Receivers.

TCP/IP

The Blustream MX44VW Matrix can be controlled via TCP/IP.

For the full list of protocols please see ‘MX44VW Control Protocols’ located at the

rear of this manual.

The MX44VW Matrix features a built-in web browser user interface allowing con-

trol and configuration of the matrix. For further details please see page 21 ‘Web

Browser User Interface’.

A ‘Straight-through’ RJ45 patch lead should be used

RS-232 2-Way

The Blustream Matrix can be controlled via a 9-pin serial cable.

For the full list of protocols please see ‘MX44VW Control Protocols’ located at the

rear of this manual.

Details of RS232 pin assignment and communication are adjacent. Please note

that depending on your control device serial port pin configuration you may

require either a ‘Straight’ RS-232 cable or ‘Null-modem’ type.

MX44VW Control Ports

BLUSTREAM RS-232 REMOTE CONTROL

CONSOLE

PIN Assignment PIN Assignment

1 NC 1 NC

2 Tx 2 Rx

3 Rx 3 Tx

4 NC 4 NC

5 GND 5 GND

6 NC 6 NC

7 NC 7 NC

8 NC 8 NC

9 NC 9 NC

Baud Rate: 57600 bps

Data Bit: 8-bit

Parity: None

Stop Bit: 1-bit

Flow Control: None

A B

C D

MX44VW USER MANUAL

www.blustream.co.uk

EDID: IN ALL DF00

HDMI: 1080P @ 60HZ

EDID Management - Global or individual input settings

The following characters show adjusting the EDID for ‘All’ inputs (Global). Current EDID value is DF00 (Default setting 0) which is 1080p @ 60Hz.

To change the EDID value for source inputs using the Matrix front panel buttons press the following:-

a. Press MENU button.

b. Panel will display ‘EDID settings’. Press SELECT button

c. Select the input you wish to fix the EDID on (1-4) or select ‘All’. Use UP/DOWN buttons to toggle selection and ENTER button to

confirm.

d. Select video resolution required (1080p, 1080i DVI etc). Use UP/DOWN buttons to toggle selection and SELECT button to confirm.

Options are standard EDID settings (DF00-DF04) or 'COPY' EDID from outputs 1-4.

e. Press the ESC button to exit.

Matrix Front Panel Control

Turning On/O HDMI outputs

It is possible to turn o each individual HDMI output using RS-232, TCP/IP or in-built Web GUI interface. This can be helpful when using panels

with a 'signal sense' power on/o feature.

Please see page 17 for list of product RS-232 and Telnet commands.

Note: There is no indication on the front panel to inform users that the outputs of the Matrix have been turned o. If you are unsure of the

status of the zone outputs you can force all outputs back on in one of two ways:

• Powering OFF/ON the matrix. All outputs will be turned on when powered up.

• Zone outputs can be forced back on by pressing and holding ‘OUTPUT 1’ button on the front panel for 10 seconds. The matrix will

reset and all outputs will be turned back on.

contact [email protected]o.uk / support@blustream.com.au

MX44VW USER MANUAL

Matrix Mode

The following shows how to activate ‘Matrix’ mode and change source inputs.

Matrix Mode Selection

1. To enter ‘Matrix’ mode first press ‘MATRIX’ button .

To confirm selection press the ‘ENTER’ button.

Source Selection

2. To change source selection per HDMI output press the desired ‘OUTPUT’ button (1-4) or ‘ALL’.

3. Press desired source ‘INPUT’ button.

The display will show both the source input selected and if this is HDMI (H) or VGA (V) video type (see above).

MX 1 2 3 4

IN 2H 1H 3V 4H

Matrix Front Panel Control

Video Input Type Selection

The MX44VW allows you to switch between HDMI and VGA+ audio per source input. It is only possible to select either HDMI or VGA per source

and it is not possible to view both video types on the same input, I.E- You cannot select HDMI input 1 and VGA input 1 at the same time.

1. To change input video type first press ‘INPUT’ button (1-4).

2. The chosen input number will start to flash.

3. Press either the ‘HDMI’ or ‘VGA’ select button.

A. When HDMI is selected the letter ‘H’ will be displayed under the source input number.

B.When VGA is selected the letter ‘V’ will be displayed under the source input number.

IN 1 2 3 4

SRC H V H V

A B A B 1

Understanding the display:

A. ‘MX’ shows that the products is in Matrix mode.

B. Indicates the output

C. Indicates the source input selected (1-4)

D. Indicates the video signal type (V or H). H=HDMI, V=VGA

MX44VW USER MANUAL

www.blustream.co.uk

Matrix Front Panel Control

Video Wall Mode

The following shows how to active ‘Video Wall’ mode, change screen layouts and change source inputs

Selecting Video Wall Mode:

1. To select Video Wall mode first press ‘Video Wall’ button

2. The display will change and the current screen layout configuration will begin to flash. You must select the required screen

configuration using the ‘UP’ or ‘DOWN’ buttons. The screen layouts are:

CHANGE MODE TO

3. Press the ‘ENTER’ button to finalise the Video Wall configuration.

2 x 2 1 x 4 4 x 1

Understanding the display:

A. ‘VW’ shows that the products is in Video Wall mode.

B. Indicates the screen configuration currently selected.

C. * Indicates the current screen configuration shown is active.

D. [EN] is a reminder to press ‘ENTER’ button to finalise selection.

VW 2X2 * [EN]

B C D

contact [email protected]o.uk / support@blustream.com.au

MX44VW USER MANUAL

Matrix Front Panel Control

Video Wall Mode

Changing Source inputs when in Video Wall mode:

1. To change the source input selection first press ‘Video Wall’ button

The display will change showing the current screen layout configuration and input selected.

2. Press desired ‘INPUT’ button (1-4)

Changing Source input video types between HDMI and VGA when in Video Wall mode:

See page 7 - ‘Video input type selection’

VW: 2 x 2 [EN]

B C D

Changing the screen configuration when in Video Wall mode:

1. To change screen configuration first press ‘Video Wall’ button

2. The display will change and the current screen layout configuration will begin to flash. You must select the required screen

configuration using the ‘UP’ or ‘DOWN’ buttons.

3. Press the ‘ENTER’ button to finalise selection.

Understanding the display:

A. ‘2 x 2’ shows that the current screen configuration selected/to be selected.

B. Indicates the source input currently selected.

C. Indicates the video signal type (V or H). H=HDMI, V=VGA

D. [EN] is a reminder to press ‘ENTER’ button to finalise the selection.

[IN 1-4] is a reminder of source inputs available.

IN: 1 H [IN 1-4]

MX44VW USER MANUAL

www.blustream.co.uk

Matrix Front Panel Control

Multi-View Mode

The following shows how to active ‘Multi-View’ mode, change screen layouts and change source input selection.

When in Multi-View mode all HDMI outputs will display the same Multi-View selected layout.

Selecting Multi-View Mode:

1. To select Multi-View mode first press ‘Multi-View’ button

2. The display will change and the current screen layout configuration will begin to flash. You must select the required Multi-View

screen configuration (0-9) using the ‘UP’ or ‘DOWN’ buttons. The screen layouts are:

CHANGE MODE TO

3. Press the ‘ENTER’ button to finalise the Multi-View configuration.

Understanding the display:

A. ‘MV’ shows that the products is in Multi-View mode.

B. Indicates the screen configuration currently selected.

C. * Indicates the current screen configuration shown is active.

D. [EN] is reminder to press ‘ENTER’ button to finalise selection.

* Please note that 'layout 0' is the default configuration

Layout 9 has been designed for use with VGA source inputs that are not standard 16:9 size

MV LAYOUT 2 * [EN]

B C D

Layout 0 Layout 1 Layout 2 Layout 3

Layout 4 Layout 5 Layout 6 Layout 7

Layout 8 Layout 9

= Window 1

= Window 2

= Window 3

= Window 4

Inhaltsverzeichnis

Andere Blu Stream Medienkonverter Handbücher

Blu Stream

Blu Stream IP100UHD-TX Bedienungsanleitung

Blu Stream

Blu Stream SP12AB-V2 Bedienungsanleitung

Blu Stream

Blu Stream DAC11AU Bedienungsanleitung

Blu Stream

Blu Stream DA11AU Bedienungsanleitung

Blu Stream

Blu Stream DIG11AU Bedienungsanleitung

Blu Stream

Blu Stream HMXL42ARC Bedienungsanleitung

Blu Stream

Blu Stream DAC12A U Bedienungsanleitung

Blu Stream

Blu Stream HEX70HDU-KIT Bedienungsanleitung

Blu Stream

Blu Stream DA22XLR-WP-US Bedienungsanleitung

Blu Stream

Blu Stream HDCP11AB Bedienungsanleitung

Blu Stream

Blu Stream BluStream HD11AU Bedienungsanleitung

Blu Stream

Blu Stream DA22XLR-WP Bedienungsanleitung

Blu Stream

Blu Stream HEX11WP-TX Bedienungsanleitung

Blu Stream

Blu Stream SP14CS Bedienungsanleitung

Blu Stream

Blu Stream Dante DA44AU Bedienungsanleitung

Blu Stream

Blu Stream HMXL44CS-KIT Bedienungsanleitung

Blu Stream

Blu Stream Dante DA11D Bedienungsanleitung

Blu Stream

Blu Stream HD12DB Bedienungsanleitung

Blu Stream

Blu Stream DAC13DB Bedienungsanleitung

Blu Stream

Blu Stream DA11AEN Bedienungsanleitung

Blu Stream

Blu Stream SP12CS Bedienungsanleitung

Blu Stream

Blu Stream SC11HD-V2 Bedienungsanleitung

Blu Stream

Blu Stream Multicast ACM200 Bedienungsanleitung

Blu Stream

Blu Stream SP14AB-V2 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung