Blue Ox BX2323 Bedienungsanleitung

Page 1 of 9 292-2865 Rev. H 12/7/10

2006-11 Hyundai Accent

(No Foglights)

Installation Instructions

BX2323

1. Blue Ox®towing products and accessories

are intended to be installed by Blue Ox®

Dealers who are familiar with our products and

have the equipment and knowledge to do “ﬁt

work”. When necessary, Blue Ox®Dealers can

be found at www.blueox.com or by contacting

our Customer Care Department at

(402) 385-3051.

2. Many Blue Ox®Baseplates are designed to

use existing holes and hardware to mount

the baseplate to the towed vehicle. Even

though bolts are there, do not assume they

are adequate for baseplate mounting. Always

use hardware supplied in the hardware kit

or existing hardware speciﬁed in the

Baseplate Installation Instructions.

Serial Number

Conﬁrm the towability and pre-towing

procedures for your vehicle with

the owner’s manual or contact the

vehicle’s manufacturer for speciﬁc

towing procedures.

Please read BOTH these Installation Instructions and the General Towing

Instructions before attempting to install or operate this equipment.

Bolt Size Grade 5 Grade 8

1/4” 10 14

5/16” 19 29

3/8” 33 47

7/16” 54 78

1/2” 78 119

5/8” 154 230

Bolt Torque Speciﬁcations

Torque in Foot-Pounds for Inch Bolts

Bolt Torque Speciﬁcations

Torque in Foot-Pounds for Metric Bolts

Bolt Size Grade 8.8 Grade 10.9

6MM 6 8

8MM 16 22

10MM 31 40

12MM 54 70

14MM 89 117

ﬁ

ons

Foot-Pounds for

Bolts

eee

GrGr

4”

”

8”

16”

2”

8”

Bolt

ue S

ﬁ

ations

Foot

tric Bol

Torq

Foot Pounds

for

Bol

e10 9

888

Failure to read and follow these instructions

could result in separation of the towed vehicle

from the tow bar, causing property damage,

loss of towed vehicle, personal injury or death.

WARNING

Attachment Tab Height: 13 1/2”

Attachment Tab Width: 24”

If the front of your vehicle looks different

than this, call us at (402) 385-3051.

Important:

Use only genuine factory replacement parts on your baseplate. Do NOT substitute homemade or non-typical parts. If a bolt

is lost or in need of replacement, for your safety and the preservation of your baseplate, be sure to use a replacement bolt of

the same grade (In most cases it will be Grade 5, please reference the parts list above). Replacement parts may be ordered

through your nearest Blue Ox® Dealer or Distributor. Failing to follow and/or altering these installation instructions in either

installation or required equipment will void the manufacturer’s warranty. Towing behind a non-motorized vehicle will void the

warranty.

Page 2 of 9 292-2865 Rev. H 12/7/10

2006-11 Hyundai Accent

(No Foglights) Installation Instructions

BX2323

Parts List

Ref. No. Qty. Part # Description

1 1 61-6298 Weldment, Base Plate, BX2323

2 6 61-5208 3/8-16 Nut Plate with 14 inch Wire

3 6 201-0440 3/8-16 x 1 1/2” Hex Bolt, Grd. 5, ZP

4 6 203-0010 3/8” Lock Washer

5 1 201-0655 6mm-1.0 x 30mm Hex Bolt, Grd. 8.8, ZP

6 1 203-0008 1/4” Lock Washer, ZP

7 1 201-0654 #10-16 x 1 Self Drilling Screw, ZP

8 2 201-0553 1/4-20 x 1/2” Hx. Wshd, Type F Screw

9 2 201-0192 #10-32 x 1/2” Slot, Rd. Hd. Screw

10 2 203-0054 #10 Lock Washer

11 2 202-0047 #10-32 Hex Nut

12 2 101-5822 Adapter, 4 Way Connector

13 2 62-3468 Attachment, Assembly, SF/SB (R)

2 290-0437 Receiver, Cap Plug, Blk (Not Shown)

2 229-0359 Quicklink, 3/8, ZP (Not Shown)

2 226-0046 Baseplate Safety Cable, 36” CL III (Not Shown)

Tools Required

Loctite®RED

6mm Socket

10mm Socket

12mm Socket

9/16” Socket

13/32” Drill Bit

1 1/4” Hole Saw

Reciprocating Saw

Vise Grips

Hack Saw Blade

Phillips Screwdriver

Pliers

1. Remove seven Phillips pushpins from the top

of radiator cover (see white arrows). Using the

10mm socket, remove two metric bolts (see

grey arrows) from radiator cover and lift to

remove. Set bolts, pushpins and radiator cover

aside to be reinstalled later.

Attachment Tabs:

Due to the design of the removable tabs, the

RangeFinderII tow bar can not be used. Adapters,

except the BX8833 and BX88151, can not be used

with this baseplate.

Installation Notes:

The radiator cover, fascia, air bafﬂe, air bag

sensor, washer reservoir, metal bumper and

air bag sensor are removed. The grille is

trimmed. Drilling is required. The air bag

sensor bolt is not reinstalled.

The dimensional variations between otherwise

identical vehicles can be considerable.

While the baseplate was designed for easy

installation, it may be necessary to tailor the

baseplate slightly to compensate for auto

manufacturer’s tolerances. These minor

adjustments may include ﬁling a hole slightly,

bending electrical rods or bending end plates.

The BX8869 Bulb and Socket Wiring Kit is

recommended for this vehicle.

Installation Instructions:

Page 3 of 9 292-2865 Rev. H 12/7/10

2. Using the 8mm socket, remove one metric

bolt from edge of fascia, just inside wheel well.

Do this to both sides of the vehicle. Set bolts

aside to be reinstalled later.

Possible Location for the BX8869

Bulb and Socket Wiring Kit.

Handling of some cosmetic parts

when installing this product may

require the use of protective covers,

rags, specialty tools, etc. to prevent

damage.

2006-11 Hyundai Accent

(No Foglights) Installation Instructions

BX2323

3. Remove two pushpins from the bottom corner

of fascia. Do this to both side of the vehicle.

Set pushpins aside to be reinstalled later.

4. Remove two pushpins from the tabs on the

bottom center of fascia. Pull upper corners of

fascia to the side to release from upper two

tabs. Do this to both sides of the vehicle. Pull

fascia forward to remove. Set pushpins and

fascia aside carefully to be reinstalled later.

Page 4 of 9 292-2865 Rev. H 12/7/10

6. On the passenger’s side, disconnect the hose

and electrical connection from the washer

reservoir. Using the 10mm socket, remove

three metric bolts from the washer reservoir.

Remove washer reservoir. Set bolts and

reservoir aside to be reinstalled later.

5. On the driver’s side, use the 10mm socket to

remove two metric bolts from the air bafﬂe. Set

bolts and air bafﬂe aside to be reinstalled later.

2006-11 Hyundai Accent

(No Foglights) Installation Instructions

BX2323

Page 5 of 9 292-2865 Rev. H 12/7/10

7. Just above the center of metal bumper, press

the clip on the horn cable to release it (see

grey arrow). Disconnect the cable from four tie

clips along the horn cable - between the horn

and the air bag sensor on the driver’s side.

Move the cable out of the way to prepare the

area for baseplate installation (leave cable

connected to the air bag sensor and move

out of the way to prepare area for baseplate

installation).

8. On the passenger’s side, remove the electrical

grounds (see white arrows) and move out of

the way for baseplate installation.

9. Using the 10mm socket, remove one metric

bolt from top section of metal bumper bracket

(see white arrow). Using the 12mm socket,

remove ﬁve metric bolts from the metal

bumper bracket (see grey arrows). Do this to

both sides of the vehicle. Pull metal bumper

bracket forward to remove. Set bolts, metal

bumper and bracket aside to reinstall later.

10. Using the 1 1/4” hole saw, drill one hole

through the frame end into the frame rail (to

insert nut plates later). Note: We recommend

spraying the surface with an anti-corrosive

paint after drilling. Do this to both sides of the

vehicle.

When using power drills be aware of the

dangers of torque and drill bit length.

2006-11 Hyundai Accent

(No Foglights) Installation Instructions

BX2323

Page 6 of 9 292-2865 Rev. H 12/7/10

14. On the driver’s side, align front two baseplate

holes with existing air bag sensor holes (see

white arrows). Insert existing bolt from air bag

sensor into upper, front hole. Clamp baseplate

into place using vise grips. Using baseplate

as a template, drill three holes into frame

rail with the 13/32” drill bit (see grey arrows).

Baseplate painted white for illustration.

Actual baseplate will be powder-coat black.

13. Bend coolant line brackets (see white arrows)

upward toward radiator to make room for

baseplate installation. Using zip ties, secure

the bushing of upper section of coolant line

(see grey arrow) to cross member of the

radiator support bar.

12. Using the reciprocating saw, make a horizontal

cut in the radiator support ribbing ﬂush with

the bottom of the frame rail. Make another

horizontal cut on the radiator support ribbing

3 1/2” down. Using the pliers, ﬂatten the

ribbing area between the cuts (see grey

arrows). Using the pliers, ﬂatten a 1/2” section

of the frame support ribbing where it meets the

frame rail (see white arrow). Do this to both

sides of the vehicle.

11. On the driver’s side, remove the electrical

grounds (see white arrows) and move out

of the way for baseplate installation. Using

the 6mm socket, remove the metric bolt from

the air bag sensor (see grey arrow) and

move sensor out of way. Set bolt aside to be

reinstalled later.

2006-11 Hyundai Accent

(No Foglights) Installation Instructions

BX2323

Page 7 of 9 292-2865 Rev. H 12/7/10

15. On the driver’s side, insert 3/8-16 nut plates

through frame end hole. Align to the lower two

drilled holes (see white arrows). Install

3/8-16 x 1 ½” hex bolts with 3/8” lock washers

and tighten. Trim excess nut plate wire.

Remove air bag sensor bolt (see grey arrow).

16. On the passenger’s side, align baseplate

with washer reservoir hole and insert existing

bolt (see white arrow). Using the baseplate

as a template, drill three holes into the frame

rail with the 13/32” drill bit (see grey arrows).

Insert 3/8-16 nut plates through frame end

hole. Insert 3/8-16 x 1 1/2” hex bolts and 3/8”

lock washers and tighten to nut plates . Trim

nut plate wires. Remove washer reservoir bolt.

18. On the driver’s side, reinstall air bafﬂe’s

existing bolts to upper rear and lower middle

baseplate holes (see grey arrows). Reconnect

horn cable to air bag sensor. Reinstall sensor

to the top front baseplate hole and insert

sensor pin to lower front hole. Reconnect

electrical grounds with the 6mm hex bolt and

1/4” lock washer (see white arrow).

17. Reinstall metal bumper and bracket. Route

the horn cable through the side of the metal

bumper and out through backside of the metal

bumper (see white arrows). Connect the horn

cable (see grey arrow).

BE SURE TO USE LOCTITE®RED ON ALL BOLTS

BEFORE TIGHTENING. TIGHTEN ALL BOLTS

ACCORDING TO THE TORQUE CHART ON THE

FRONT PAGE OF THESE INSTRUCTIONS OR ON

PAGE 3 OF THE BASEPLATE TOWING GENERAL

INSTRUCTIONS.

2006-11 Hyundai Accent

(No Foglights) Installation Instructions

BX2323

Page 8 of 9 292-2865 Rev. H 12/7/10

20. Align the fascia to its original position and,

using a hack saw blade, trim necessary

openings in the grille for the attachment tabs.

Do this to both sides of the vehicle.

19. On the passenger’s side, reinstall washer

reservoir using existing bolts. Reconnect

electrical grounds to the lower front bolt hole

using the #10-16 x 1 self drilling screw (see

white arrow).

Be sure that ALL electrical connections

are plugged in properly and functioning

BEFORE installing the fascia.

DEALER or INSTALLER:

Be certain the user receives the

instruction sheets for their products.

22. Reinstall the fascia, radiator cover, pushpins

and bolts.

Install the tow bar and safety cables

according to the instructions provided in their

packages. When demonstrating this to the

customer, be sure to include all the contents

and packages.

Do NOT substitute other devices if the tow

bar pins and clips are misplaced.

21. Attach the permanent baseplate safety

cables to the provided convenience link on

the baseplate (see grey arrow). The photo

above shows the recommended installation

of the cables to frame of vehicle (see white

arrow). Additional options may interfere with

suggested mounting; in this case secure

the cables to a solid piece of the frame as

described in the instructions included with the

permanent baseplate safety cables. Be sure

the safety cables do not rub against any hoses

or moving parts. Do this to both sides of the

vehicle.

2006-11 Hyundai Accent

(No Foglights) Installation Instructions

BX2323

One Mill Road, Industrial Park

Pender, Nebraska 68047

Phone: (402) 385-3051

Fax: (402) 385-3360

www.blueox.com

CUSTOMER SERVICE COMMITMENT

Blue Ox is committed to providing you with

exceptional customer care throughout your lifetime

with our products. Our team is here to assist you

with any questions you may have regarding the

performance of your product. Simply call 1-(402)

385-3051 and you can speak with our customer

care team.

Additionally, please visit our website to see

which rallies our Destination America team will

be attending. For a nominal fee, our service

technician will service your towing system to

ensure it’s in proper working condition. Also as

a commitment to our customers, should you visit

our factory you can stay at our full service Blue

Ox campground at no charge along with enjoying

a factory tour.

Again thank you for being our customer and for

the conﬁdence you have shown in the performance

of our products. It is because of customers like

you we enjoy the success we have today.

Shown without removable tabs installed.

Shown with removable tabs installed.

Page 9 of 9 292-2865 Rev. H 12/7/10

If the baseplate is in an accident, it must

be replaced. DO NOT use it again! An

accident can cause unseen damage and

using it again could result in more dam-

age or serious injury. DO NOT use the

baseplate if it is damaged or missing parts.

2006-11 Hyundai Accent

(No Foglights) Installation Instructions

BX2323

Inhaltsverzeichnis

Andere Blue Ox Autozubehör Handbücher

Blue Ox

Blue Ox BX3776 Bedienungsanleitung

Blue Ox

Blue Ox SwayPro BXW0551 Bedienungsanleitung

Blue Ox

Blue Ox BX2610 Bedienungsanleitung

Blue Ox

Blue Ox BX4102 Bedienungsanleitung

Blue Ox

Blue Ox BX1719 Bedienungsanleitung

Blue Ox

Blue Ox BedSaver BXR4401 Bedienungsanleitung

Blue Ox

Blue Ox BX1504 Bedienungsanleitung

Blue Ox

Blue Ox DH2303 Bedienungsanleitung

Blue Ox

Blue Ox Patriot BRK2010 Bedienungsanleitung

Blue Ox

Blue Ox BX1136 Service-Handbuch

Blue Ox

Blue Ox BX1133 Bedienungsanleitung

Blue Ox

Blue Ox BX1502 Bedienungsanleitung

Blue Ox

Blue Ox BX2711 Bedienungsanleitung

Blue Ox

Blue Ox SwayPro BXW0553 Bedienungsanleitung

Blue Ox

Blue Ox BX1678 Bedienungsanleitung

Blue Ox

Blue Ox BX2239 Bedienungsanleitung

Blue Ox

Blue Ox BX88420 Bedienungsanleitung

Blue Ox

Blue Ox SportCarrier II Technisches Datenblatt

Blue Ox

Blue Ox BedSaver BXR4102 Bedienungsanleitung

Blue Ox

Blue Ox BX7365 Bedienungsanleitung

Blue Ox

Blue Ox BX2800 Bedienungsanleitung

Blue Ox

Blue Ox BX1120 Bedienungsanleitung

Blue Ox

Blue Ox TRION BX7520P Bedienungsanleitung

Blue Ox

Blue Ox bx1126 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung