Bluesky Eliptig-S A00-1515 1 A Bedienungsanleitung

S15-1006_1_A

UVC Disinfection System

User Manual

•Model A00-1515_1_A (50Hz / 60Hz)

S15-1006_1_A

1Safety Warnings____________________________________________________________3

2Labelling__________________________________________________________________5

2.1 Labelling_____________________________________________________________ 5

3Technical Specification ______________________________________________________6

4Transportation and Installation. _______________________________________________7

4.1 Transport Damage. ____________________________________________________ 7

4.2 Environmental Transport & Storage Conditions. ____________________________ 7

5System Operation.___________________________________________________________8

6General Maintenance_______________________________________________________11

6.1 Cleaning the Equipment _______________________________________________ 11

6.2 Visual Inspection_____________________________________________________ 11

6.3 Lamp Renewal_______________________________________________________ 11

6.4 Servicing and Maintenance Schedule ____________________________________ 11

6.5 Safe Disposal________________________________________________________ 12

S15-1006_1_A

1Safety Warnings

The Eliptig-S is designed to emit UVC radiation at 254nm which has been proven to be highly effective at

killing bacteria and viruses by destroying the molecular bonds that hold their DNA together.

The Eliptig-S must only be operated in a secure environment. DO NOT operate the device while people are

in the area.

Persons operating the unit must wear the safety glasses provided along with appropriate PPE.

The User Manual must always remain legible and kept with the Eliptig-S.

DO NOT use the power cable to manoeuvre the device.

WARNING –MERCURY HAZARD: Do not break the UVC lamps. Each UVC lamp contains small amounts

of mercury that can have harmful effects if exposed or ingested.

•Exposure to mercury may cause redness or irritation.

•In the case of a broken UVC lamp, sweep up all the broken glass and debris into a plastic bag and

secure it with a seal.

•Dispose of broken or UVC lamp debris at a local recycling center.

•Do not use a vacuum cleaner or incinerator to collect or dispose of any lamp debris.

WARNING - UVC LIGHT HAZARD: Use of controls, adjustments or performance of procedures

other than those specified herein may result in hazardous radiation exposure. No attempt to

operate this UV system until the User Manual has been read and fully understood. In addition, a

clear understanding of the biological effects of the interaction of UV light with tissue / eyes

should be prerequisite to the use of this UV system. When not in use the UV equipment should

be protected from unqualified use. UVC radiation can cause severe burns (of the skin) and eye

injuries (photokeratitis). Avoid direct skin exposure to UVC radiation and never look directly into

a UVC light source, even briefly.

S15-1006_1_A

WARNING: Do not modify this equipment without authorization of the manufacturer.

The manufacturer of the Eliptig-S has made every effort to provide as many safety features as possible to

assure personal safety. To be effective, these safety features must be utilised and not ignored.

Electrical Safety

WARNING: To avoid risk of electric shock, this equipment must only be connected to a supply mains with

protective earth.

HIGH VOLTAGE WARNING: There are no user serviceable parts inside the unit, only manufacturer spares

and accessories should be used with the system, non-standard cables, components and accessories may

degrade performance, create safety hazards or affect EMC performance. NO ATTEMPT SHOULD BE

MADE TO REMOVE THE OUTER COVER

WARNING: Use of this equipment adjacent to or stacked with other equipment should be avoided because

it could result in improper operation. If such use is necessary, this equipment and the other equipment

should be observed to verify that they are operating normally.

S15-1006_1_A

2Labelling

2.1 Labelling

UV Hazard Warning (located on base top)

Emergency Stop (located on base rear)

Consult Accompanying Documents (located on base front)

Waste Electronic & Electrical Equipment (WEEE) (located on base rear)

Manufacturers Label (located on Rear)

S15-1006_1_A

3Technical Specification

Electrical Class:

Class 1

Voltage (V):

100-240Vac

Current (I):

100Vac, 6.5 Amps

240Vac, 3 Amps

Frequency (Hz):

50/60Hz

Input Power (W):

640 Watts

Output UV Radiation:

140 Watts

Wavelength (nm)

254nm

Useful Lamp Life (Hrs)

8000 Hours

User Interface:

7” Touch Screen

4 button key fob module, 433MHz, 100m range

Ingress Protection

IPX0

Mains Fuses (I)

T10AH 250Vac

Motion Detection:

4 x Passive Infrared Sensors

Conditions of Use

100C to 300C Non-condensing humidities below 75% RH

Dimensions: (mm)

800mm x 400mm x 1345mm

Weight: (kg)

25 kg

Standards:

Electrical Safety: EN 61010-1:2010. EN 61010-2-040:2015,

EMC: EN 61326-2-1:2013 FCC CFR 47 Parts 15.107 & 15.109;

ICES-003 Issue 6.

•Figure 1 Dimensions

S15-1006_1_A

4Transportation and Installation.

4.1 Transport Damage.

The Eliptig-S has been carefully packed and should arrive at its destination in perfect condition. Upon

delivery, please check that the external packaging is not damaged. If signs of damage are present, or the

shock detector labels have been activated, please report them to the shipping carrier and the Customer

Service Department within 24 Hrs.

4.2 Environmental Transport & Storage Conditions.

The transport & storage conditions for the Eliptig-S were determined from specifications set by the

manufacturers of critical components as follows: -

Temperature +5C to +40C

Relative Humidity 35% to 65% Non-Condensing.

Atmospheric Pressure 500 –1060 hPa

S15-1006_1_A

5System Operation.

AC Input

•IEC C14 Switched Mains

Input Module

•Fuses T10AH

Emergency Stop Switch

•Twist to unlock clockwise

Motion Detection

•4 x Passive Infrared

Sensors

User Interface

•7” Touch Screen Display

S15-1006_1_A

Figure 1 UV Lamps OFF State

System State

•OFF

•COUNTDOWN

•ON

•HALTED

UV Lamp Hours Remaining

•8000 Hour Lamp Life

System Operation

•Start / Pause

•Stop / Reset

System Timer

•Adjustable in 10

Minute Intervals

Disinfection Time

•Increase

•Decrease

Figure 2 30 Second Delay Timer Countdown

S15-1006_1_A

Figure 3 UV Lamps ON State

Figure 4 UV Lamp Operation Halted Motion Detected (Lamps OFF)

Figure 5 Remote Control Module

Inhaltsverzeichnis

Andere Bluesky Zubehör Handbücher

Bluesky

Bluesky Pennine Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung