Bosch PRS-1AIP1 Bedienungsanleitung

IP Audio Interface

PRS-1AIP1

en Operating Manual

Table of contents

1Important Safety Instructions 5

2Short information 6

2.1 Purpose 6

2.2 Digital document 6

2.3 Intended audience 6

2.4 Related documentation 6

2.5 Alerts and notice signs 6

2.6 Conversion tables 7

2.7 Disclaimers 7

2.7.1 Bosch Security Systems B.V. 7

3System overview 8

3.1 Application 8

3.2 Key product features 8

3.3 Package content 8

3.4 Product view 9

3.4.1 Front view 9

3.4.2 Rear view 10

4Installation 12

4.1 Mechanical installation 12

4.2 Network (step 1) 12

4.3 Audio Outputs (step 2) 12

4.4 Power supply (step 3) 12

4.5 IP address (step 4) 12

4.5.1 No DHCP server is found 13

4.6 Audio Inputs 1/2 13

4.7 Control Inputs 13

4.8 Control Outputs 13

5Connection options 14

5.1 Unicast (point to point) 14

5.2 Multiple Unicast 14

5.3 Broadcast 14

5.4 Multicast 15

5.5 Re-broadcast 15

6Configuration 16

6.1 Connect to web browser 16

6.2 Configuration page 17

6.2.1 Network 18

6.2.2 Streaming 19

6.2.3 Partner Table 20

6.2.4 Outgoing Route Table 22

6.2.5 Control 23

6.2.6 Audio Settings 24

6.2.7 Supervision 27

6.2.8 Control Input Mapping Table 29

6.2.9 Control Output Mapping Table 30

6.2.10 Serial (RS-232/RS-485) 31

6.2.11 SNMP 32

IP Audio Interface Table of Contents | en 3

Bosch Security Systems B.V. Operating Manual 2013.03 | V2.0 |

6.2.12 Security 33

6.2.13 Default settings 34

6.2.14 Configuration view 35

6.2.15 Update 36

7Operation 39

7.1 Status page 39

7.1.1 Control Inputs (1..8) 39

7.1.2 Control Outputs (1..8) 40

7.1.3 Audio 40

7.1.4 Codec 40

7.1.5 Power, Fault & Temperature 40

7.1.6 Last Caller 41

7.1.7 Restart Page 41

8Maintenance 42

9Technical data 43

9.1 Electrical 43

9.2 Mechanical 44

9.3 Environmental conditions 44

9.4 EMC and Safety 45

4en | Table of Contents IP Audio Interface

2013.03 | V2.0 | Operating Manual Bosch Security Systems B.V.

Important Safety Instructions

The following important safety instructions are applicable to the PRS‑1AIP1 IP Audio Interface

apparatus.

– Read these instructions.

– Keep these instructions.

– Heed all warnings.

– Follow all instructions.

– Do not use this apparatus near water.

– Only clean the apparatus with a dry cloth.

– Do not block any ventilation openings.

– Always install the apparatus according to Bosch installation instructions.

– Do not install the apparatus near any heat sources, for example: radiators, heat registers,

stoves or other apparatus (including amplifiers) that generate heat.

– Protect the power supply cord from damage. For example: being walked on, pinched near

the plug or from stress at the point where the power supply cord exits from the

apparatus.

– Only use the apparatus with attachments and accessories supplied or recommended by

Bosch.

– This apparatus should only be serviced by qualified service personnel.

– If the apparatus has been damaged, servicing will be required. This includes damage

caused by: liquid spillage or objects falling into the apparatus and/or the apparatus being

exposed to rain or moisture. The apparatus must also be serviced if it does not function

normally, it has been dropped and/or if there is damage to the power supply cord and

plug.

– To prevent a risk of electrical shock, do not attempt to service the apparatus yourself.

Opening or removing the apparatus covers may expose you to dangerous voltages or

other hazards.

IP Audio Interface Important Safety Instructions | en 5

Bosch Security Systems B.V. Operating Manual 2013.03 | V2.0 |

Short information

Purpose

The purpose of this manual is to provide information required for installing, configuring,

operating and maintaining the PRS‑1AIP1 IP Audio Interface.

Digital document

This manual is also available as a digital document in the Adobe Portable Document Format

(PDF).

Intended audience

This manual is intended for installers and users of a PRS‑1AIP1 IP Audio Interface.

Related documentation

Plena Voice Alarm System Operating Manual and Praesideo Public Address and Emergency

Sound System Installation and User Instruction manual.

Alerts and notice signs

The following alerts and notices are used in this manual. The alert type is closely related to the

effect that may be caused if it is not observed.

Caution!

The equipment or the property can be damaged, or persons can be lightly injured if the alert

is not observed.

In this manual a ‘notice’ is used to provide tips, or to give some extra information:

Notice!

Alert containing additional information. Usually, not observing a ‘notice’ does not result in

damage to the equipment or personal injuries.

2.1

2.2

2.3

2.4

2.5

6en | Short information IP Audio Interface

2013.03 | V2.0 | Operating Manual Bosch Security Systems B.V.

Conversion tables

In this manual, SI units are used to express lengths, masses, temperatures, etc. These can be

converted to non-metric units using the following information.

Non-metric unit SI unit SI unit Non-metric unit

1 in = 25.4 mm 1 mm = 0.03937 in

1 in = 2.54 cm 1 cm = 0.3937 in

1 ft = 0.3048 m 1 m = 3.281 ft

1 mi = 1.609 km 1 km = 0.622 mi

Non-metric unit SI unit SI unit Non-metric unit

1 lb = 0.4536 kg 1 kg = 2.2046 lb

Non-metric unit SI unit SI unit Non-metric unit

1 psi = 68.95 hPa 1 hPa (= 1 mbar) = 0.0145 psi

Disclaimers

Bosch Security Systems B.V.

Although every effort has been made to ensure the information and data contained in these

manual is correct, no rights can be derived from the contents.

Bosch Security Systems B.V. disclaim all warranties with regard to the information provided in

these instructions.

In no event shall Bosch Security Systems B.V. be liable for any special, indirect or

consequential damages whatsoever resulting from loss of use, data or profits, whether in

action of contract, negligence or other tortuous action, arising out of or in connection with the

use of the information provided in these Installation and User Instructions.

2.6

2.7

2.7.1

IP Audio Interface Short information | en 7

Bosch Security Systems B.V. Operating Manual 2013.03 | V2.0 |

System overview

Application

The PRS‑1AIP1 IP Audio Interface is a universal, Internet Protocol based audio device

supporting VoIP and Audio over IP applications. It is used for bridging audio and contact

closures over long distance LAN and WAN networks. It extends and interfaces to e.g.

Praesideo and non network based traditional public address systems, like Plena, without the

need for a PC during operation.

The device has analog audio line inputs and line outputs for easy interfacing, it has optional

pilot tone supervision and generation for emergency sound purposes. One audio input can be

switched to microphone sensitivity with built‑in microphone supervision.

Control inputs and outputs can be used to set up an audio connection to start a remote call,

but also to pass remote fault events to e.g. a system controller. Also, the control inputs offer

cable and connection supervision, and can activate (remote) control outputs.

Key product features

Some key product features are:

– Digital audio transmission between public address systems on remote locations

– Designed to comply to international standards for emergency sound systems

– Supervised control inputs and control outputs

– A single unit can act as transmitter, receiver or both

– Installation and configuration via standard web browser

– Support for re‑broadcasting to extend the system size

– Built‑in configurable audio delay

Package content

The package contains:

– PRS‑1AIP1 IP Audio Interface

– CD with software and Installation and User Instructions

– Power supply for universal input voltage

– Screw block terminals (4 x 8 pin, 6 x 3 pin)

– Label stickers for screw block terminals

3.1

3.2

3.3

8en | System overview IP Audio Interface

2013.03 | V2.0 | Operating Manual Bosch Security Systems B.V.

Product view

Front view

Shows the controls and indicators on the front panel.

1 2 3

Figure 3.1: Front view

1 Reset button – Press this recessed button briefly (1..3 seconds) to

reset and start-up the device

– If you press it until the red LED (2) flashes (between 5

and 10 seconds) the device will be reset to factory

defaults, and configuration settings will be lost. The

network settings will not be lost

2 Green and red status

LEDs

The status LEDs show the device status. The following

modes exist:

Normal operation (power ON and no Errors)

– Green: ON

– Red: OFF

Searching IP address

– Green flashes five times, pauses four times, repeating

– Red flashes continuously

No application software loaded/Reset status

– Green: ON

– Red: flashes

Error detection

– Red: ON

– Green flashes five times: corrupt application loaded or

IP address conflict

– Green flashes three times: network hardware could

not be initialized or a corrupt MAC address

3Green LEDs (1...8) for

control input status

The status LEDs correspond to the control inputs with the

same number.

– All ON: searching for IP address or all inputs activated

– All OFF: IP address found and network connection

established and all inputs deactivated

– One or more ON: one or more inputs activated

– One or more slow flashing: open input circuit(s), while

supervision is enabled

– One or more fast flashing: shorted input circuit(s),

while supervision is enabled

3.4

3.4.1

IP Audio Interface System overview | en 9

Bosch Security Systems B.V. Operating Manual 2013.03 | V2.0 |

Rear view

Shows the connections on the rear panel.

4 6

5 7 7 911 16 17

8 12 13 14

10 15

1 1 13 31 88 1 3

Figure 3.2: Rear view

4Control Outputs 1..4 Default: open contacts (voltage free relay

contact).

– 1-2: CO1

– 3-4: CO2

– 5-6: CO3

– 7-8: CO4

5 Control Outputs 5..8 Default: open contacts (voltage free relay

contact).

– 1-2: CO5

– 3-4: CO6

– 5-6: CO7

– 7-8: CO8

6 Control Inputs 1..4 Default: open contacts (non isolated, 0 is

connected to ground).

– 1-2: CI1

– 3-4: CI2

– 5-6: CI3

– 7-8: CI4

7 Control Inputs 5..8 and Fault Relay out Default: open contacts (non isolated,

shared 0 is connected to ground, internal

pull-up current source).

– 1-2: CI5

– 3-4: CI6

– 5-6: CI7

– 7-8: CI8

Fault Relay out

Default (no fault): open contacts (voltage

free relay contact).

– 7-8: Fault contact

8Audio Output 2 Balanced, line level with pilot tone

generation.

– 1: -

– 2: ground

– 3: +

3.4.2

10 en | System overview IP Audio Interface

2013.03 | V2.0 | Operating Manual Bosch Security Systems B.V.

Andere Handbücher für PRS-1AIP1

Inhaltsverzeichnis

Andere Bosch Zubehör Handbücher

Bosch

Bosch BME680 Bedienungsanleitung

Bosch

Bosch Rexroth HEDE 10-3 Series Bedienungsanleitung

Bosch

Bosch RADION glass break Bedienungsanleitung

Bosch

Bosch PLS Bedienungsanleitung

Bosch

Bosch DS924iPET Bedienungsanleitung

Bosch

Bosch IMSA GT Class Scrutineering System Bedienungsanleitung

Bosch

Bosch BGS6235GB Bedienungsanleitung

Bosch

Bosch BME280 Bedienungsanleitung

Bosch

Bosch ISC-PDL1-W18G Bedienungsanleitung

Bosch

Bosch Rexroth MM7.10 Bedienungsanleitung

Bosch

Bosch GPL 5 Professional Bedienungsanleitung

Bosch

Bosch Rexroth ID 15 Bedienungsanleitung

Bosch

Bosch Rexroth 3 842 547 200 Bedienungsanleitung

Bosch

Bosch CISS Bedienungsanleitung

Bosch

Bosch TE 600 Bedienungsanleitung

Bosch

Bosch DS924i Bedienungsanleitung

Bosch

Bosch rexroth APAS CDE V01.00.00 Bedienungsanleitung

Bosch

Bosch ISC-CDL1-WA15G Bedienungsanleitung

Bosch

Bosch CleverMixx MSM1 IN Series Bedienungsanleitung

Bosch

Bosch GPL 3 Professional Bedienungsanleitung

Bosch

Bosch FR5CUEC Bedienungsanleitung

Bosch

Bosch EQ 1/TR Bedienungsanleitung

Bosch

Bosch Rexroth ActiveMover Bedienungsanleitung

Bosch

Bosch IVAS Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung