Bosch Infrared Imager EX80 Bedienungsanleitung

INSTALLATION

INSTRUCTIONS

EX80/82

Infrared Imager™

MAN-80-82-08

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep this instruction.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with manufacturer instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves or other

apparatus (including amplifiers) that produce

heat.

9. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A

grounding type plug has two blades and a third

grounding prong. The wide blade or the third

prong is provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the power where they exit from

the apparatus.

11. Only use attachments/accessories specified by

the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has

been damaged in a way, such as power-supply

cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

IMPORTANT

For best results, please read this Instruction Booklet

prior to installing the EX80/82 Infrared Imager.

WARNING !

CSA Certified / UL Listed CLASS 2 power adaptors must be used

in order to comply with electrical safety

®surveillance

“The cameras have not been evaluated for surveillance performance.”

Bosch Security Systems, Inc. will not be responsible for

injuries or damages resulting from the

improper installation or use of any product

sold by Bosch Security Systems, Inc their agents,

distributors or dealers.

NOTE: This equipment has been tested and found to

comply with the limits for a digital device, pursuant to part

15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. As part of it's normal operation this

device can generate radio frequency energy and if not

installed and used in accordance with the installation

manual may cause interference to radio communications.

However, there is no guarantee that interference will not

occur on a particular installation. If the device does cause

interference to radio or television reception the user is

encouraged to try to correct the interference by one or

more of the following measures:

1) Fit Ferrite beads on all cable to and from the power

supply box, within the box walls.

2) Route the composite cable between the camera and the

power supply in steel conduit piping over the entire run of

the cable up to and including connection to a deep conduit

base fitted under the camera and a conduit fitting adaptor in

the wall of the PSU box.

3) Contact BOSCH Service Center for further advice.

INDEX – EX80/82 Infrared Imager™

Description………………………………………………...1

Unpacking………………………………………………....2

Parts List…………………………………………………..2

Items Required for Installation………………………….2

Initial Preparations……………………………………….3

Guidelines………………………………………………...3

1. Mounting Bracket Preparation……………….……..…...4

2. Cable/Bracket Insertion.……..……………….……….....5

3. Mounting Bracket Attachment……………….…………..6

4. Camera Mounting……….……………….….…………....7

5. Camera Lens Adjustments and Select a Window..…..10

6. LED Array-Power Adjustments………………..…….….13

7. Camera Re-Assembly…………………………….…..…14

8. Troubleshooting Guide-Camera…………....….……....15

9. Troubleshooting Guide-LEDs…….……….……...….…18

10. Mounting Hole – Diagram………………………..…....19

17. General Specifications………………………..…….….20

DESCRIPTION

The EX80/82 Infrared Imager™ consists of two cameras:

color and mono-chrome. These cameras give optimum color

performance during daylight conditions and LXR-infrared

illuminated performance in the pitch black of night.

Both cameras have “Vari-Focal” lenses, and are seamlessly

switched by a photocell when light conditions change from

day to night, ensuring “No Focus Shift”.

The all-weather housing with tough polycarbonate windows

contains all the electronics. Low voltage operation, low power

consumption, LED illuminators, thermostat controlled

defroster and solid-state CCD technology make this camera

very reliable and efficient.

A voltage regulator circuit allows for DC or AC operation, also

providing protection from voltage surges, transient spikes,

and reverse voltage.

UNPACKING

Care should be taken when unpacking the shipped unit.

Check the parts list and confirm all items have been

located. Inspect the equipment thoroughly to ensure

nothing was damaged in transit.

Contact BOSCH Service Center if a problem is noted,

see the rear page of this booklet for contact numbers.

PARTS LIST (items supplied with unit)

-EX80/82 Infrared Imager™ assembly

-Installation Instructions booklet

-EXMB028B or EXMB028W cable management

mounting bracket.

-Extra window (80illumination beam) for 4-9mm

version only.

ITEMS REQUIRED FOR INSTALLATION (not

supplied with units)

•Mounting hardware

•Mounting tools

•Camera Power supply

INITIAL PREPARATIONS

•Determine the operating voltage at the

installation site. The camera‘s Voltage Regulator

Board accepts both 10.5-40VDC and 12-28VAC

input without change to internal connections.

•Determine the optimum mounting location for

the camera. See Section 4, Camera Mounting.

•All cameras have been tested and pre-focused

with telephoto setting as factory default prior to

shipment. If any adjustment needed, it is

advisable to check the camera’s operation

before installation.

GUIDELINES

The installation of the EX80/82 Infrared Imager™ is

explained in Sections 1 to 7.

It is important that these steps are followed in numerical

order.

It is also important to follow proper safety guidelines

when installing this product.

1. MOUNTING BRACKET PREPARATON

•Use the supplied Allen Key to remove the

setscrew from the supplied mounting

bracket.

•Separate the two sections of the

mounting bracket.

EXMB.028

Mounting Bracket

SET SCREW

Andere Handbücher für Infrared Imager EX80

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bosch IP-Kamera Handbücher

Bosch

Bosch DinionHD NBN-832 Bedienungsanleitung

Bosch

Bosch NDN-921 Installationsanleitung

Bosch

Bosch DINION IP imager 9000 HD Betriebsanleitung

Bosch

Bosch NDC-225-PI Bedienungsanleitung

Bosch

Bosch NDN-265-PIO Gebrauchsanweisung

Bosch

Bosch NWC-0455-20P Bedienungsanleitung

Bosch

Bosch LTC 7960 Series Bedienungsanleitung

Bosch

Bosch NIN-51022-V3 Bedienungsanleitung

Bosch

Bosch DINION IP starlight 8000 MP Bedienungsanleitung

Bosch

Bosch EX85 Bedienungsanleitung

Bosch

Bosch NWD-455 FlexiDome Bedienungsanleitung

Bosch

Bosch DinionHD NBN-921 Bedienungsanleitung

Bosch

Bosch AUTODOME 7100i Bedienungsanleitung

Bosch

Bosch MIC IP ultra 7100i Bedienungsanleitung

Bosch

Bosch NII-41012-V3 Bedienungsanleitung

Bosch

Bosch NDC-455 Bedienungsanleitung

Bosch

Bosch Infrared Imager EX80 Bedienungsanleitung

Bosch

Bosch NBC-455 Bedienungsanleitung

Bosch

Bosch NDC-455 Bedienungsanleitung

Bosch

Bosch FLEXIDOME IP panoramic 6000 IC Bedienungsanleitung

Bosch

Bosch MIC IP fusion 9000i Bedienungsanleitung

Bosch

Bosch Flexidome IP 4000i Bedienungsanleitung

Bosch

Bosch Autodome IP 4000 HD Montageanleitung

Bosch

Bosch AN traffic 4000 IR Bedienungsanleitung

Beliebte IP-Kamera Handbücher anderer Marken

FLIR

FLIR Exx series Bedienungsanleitung

Avigilon

Avigilon H4A-BO1-IR Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWCA-C128-64 Bedienungsanleitung

ShareTech

ShareTech AV1 Bedienungsanleitung

Ezviz

Ezviz C6C Bedienungsanleitung

Melchioni

Melchioni UCAM 2015 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-4630 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Bedienungsanleitung

Mitel

Mitel 6800i Series Service-Handbuch

Vitek

Vitek VTC-IR403-212NP Bedienungsanleitung

THOMSON

THOMSON DSC - 323W Bedienungsanleitung

AVer

AVer FB2027 Bedienungsanleitung

ENFORCER

ENFORCER EV-T5105-N2SQ Bedienungsanleitung

Wansview

Wansview NC543 Bedienungsanleitung

Eneo

Eneo MCB-64A0003M0A Bedienungsanleitung

deView electronics

deView electronics CBDNI36F Bedienungsanleitung

Swann

Swann SwannEye Bedienungsanleitung

LevelOne

LevelOne IP CamSecure Bedienungsanleitung