Bosch DIVAR IP 7000 2U Bedienungsanleitung

DIVAR IP 7000 2U

DIP-7080-00N, DIP-7082-8HD

en Quick Installation Guide

Table of contents

1Safety precautions 4

1.1 General safety precautions 4

1.2 Electrical safety precautions 5

1.3 ESD precautions 6

1.4 Operating precautions 6

1.5 Important notices 7

1.6 FCC and ICES compliance 7

2System overview 8

3System setup - hardware 10

3.1 Introduction 10

3.2 Unpacking the system 10

3.3 Preparing for setup 10

3.3.1 Choosing a setup location 10

3.3.2 Rack precautions 10

3.3.3 General system precautions 11

3.3.4 Rack mounting considerations 11

3.4 Rack mounting instructions 12

3.4.1 Separating the sections of the rack rails 12

3.4.2 Installing the inner rails 13

3.4.3 Installing the outer rails to the rack 13

3.4.4 Installing the chassis into the rack 14

3.4.5 Installing the chassis into a Telco rack 15

3.5 Turning on the system 15

4System setup - first steps 16

4.1 Introduction 16

4.2 Setup instruction 16

4.3 Starting the application 16

4.4 Using Configuration Wizard 17

5Additional documentation 27

6Service and repair 28

DIVAR IP 7000 2U Table of Contents | en 3

Bosch Sicherheitssysteme GmbH Quick Installation Guide 2013.05 | V1 | DOC

Safety precautions

Observe the safety precautions in this chapter.

General safety precautions

Follow these rules to ensure general safety:

– Keep the area around the system clean and free of clutter.

– Place the chassis top cover and any system components that have been removed away

from the system or on a table so that they won't accidentally be stepped on.

– While working on the system, do not wear loose clothing such as neckties and

unbuttoned shirt sleeves, which can come into contact with electrical circuits or be

pulled into a cooling fan.

– Remove any jewelry or metal objects from your body, which are excellent metal

conductors that can create short circuits and harm you if they come into contact with

printed circuit boards or areas where power is present.

– After accessing the inside of the system, close the system back up and secure it to the

rack unit after ensuring that all connections have been made.

– The system weighs approximately 57 lbs. (25.9 kg) when fully loaded. When lifting the

system, two people at either end should lift slowly with their feet spread out to distribute

the weight. Always keep your back straight and lift with your legs.

Warning!

Interruption of mains supply:

Voltage is applied as soon as the mains plug is inserted into the mains socket.

However, for devices with a mains switch, the device is only ready for operation when the

mains switch (ON/OFF) is in the ON position. When the mains plug is pulled out of the

socket, the supply of power to the device is completely interrupted.

Warning!

Removing the housing:

To avoid electric shock, the housing must only be removed by qualified service personnel.

Before removing the housing, the plug must always be removed from the mains socket and

remain disconnected while the housing is removed. Servicing must only be carried out by

qualified service personnel. The user must not carry out any repairs.

Warning!

Power cable and AC adapter:

When installing the product, use the provided or designated connection cables, power cables

and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire.

Electrical Appliance and Material Safety Law prohibits the use of UL or CSA-certified cables

(that have UL/CSA shown on the code) for any other electrical devices.

1.1

4en | Safety precautions DIVAR IP 7000 2U

2013.05 | V1 | DOC Quick Installation Guide Bosch Sicherheitssysteme GmbH

Warning!

Lithium battery:

Batteries that have been inserted wrongly can cause an explosion. Always replace empty

batteries with batteries of the same type or a similar type recommended by the manufacturer.

Handle used batteries carefully. Do not damage the battery in any way. A damaged battery

may release hazardous materials into the environment.

Dispose of empty batteries according to the manufacturer's instructions.

Warning!

Handling of lead solder materials used in this product may expose you to lead, a chemical

known to the State of California to cause birth defects and other reproductive harm.

Notice!

Electrostatically sensitive device:

To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried

out correctly.

When handling electrostatically sensitive printed circuits, grounded anti-static wrist bands

must be worn and the ESD safety precautions observed.

Notice!

Installation should only be carried out by qualified customer service personnel in accordance

with the applicable electrical regulations.

Disposal

Your Bosch product has been developed and manufactured using high-

quality materials and components that can be reused.

This symbol means that electronic and electrical devices that have reached

the end of their working life must be disposed of separately from

household waste.

In the EU, separate collecting systems are already in place for used

electrical and electronic products. Please dispose of these devices at your

local communal waste collection point or at a recycling center.

Electrical safety precautions

Basic electrical safety precautions should be followed to protect you from harm and the

system from damage:

– Be aware of the locations of the power on/off switch on the chassis as well as the room's

emergency power-off switch, disconnection switch or electrical outlet. If an electrical

accident occurs, you can then quickly remove power from the system.

– Do not work alone when working with high voltage components.

– Power should always be disconnected from the system when removing or installing main

system components, such as the motherboard or memory modules. When disconnecting

power, you should first turn off the system and then unplug the power cords from all the

power supply modules in the system.

– When working around exposed electrical circuits, another person who is familiar with the

power-off controls should be nearby to switch off the power if necessary.

1.2

DIVAR IP 7000 2U Safety precautions | en 5

Bosch Sicherheitssysteme GmbH Quick Installation Guide 2013.05 | V1 | DOC

– Use only one hand when working with powered-on electrical equipment. This is to avoid

making a complete circuit, which will cause electrical shock. Use extreme caution when

using metal tools, which can easily damage any electrical components or circuit boards

they come into contact with.

– The power supply power cords must include a grounding plug and must be plugged into

grounded electrical outlets. The unit has more than one power supply cord. Disconnect

both power supply cords before servicing to avoid electrical shock.

– Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Temperature

Coefficient) fuses on the mainboard must be replaced by trained service technicians only.

The new fuse must be the same or equivalent as the one replaced. Contact technical

support for details and support.

Caution!

Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside

down, which will reverse its polarities. This battery must be replaced only with the same or

an equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries

according to the manufacturer's instructions.

Caution!

DVD-ROM Laser: This system comes without a DVD-ROM drive but if added: To prevent direct

exposure to the laser beam and hazardous radiation exposure, do not open the enclosure or

use the unit in any unconventional way.

ESD precautions

Electrostatic Discharge (ESD) is generated by two objects with different electrical charges

coming into contact with each other. An electrical discharge is created to neutralize this

difference, which can damage electronic components and printed circuit boards. The

following measures are generally sufficient to neutralize this difference before contact is made

to protect your equipment from ESD:

– Do not use mats designed to decrease electrostatic discharge as protection from

electrical shock. Instead, use rubber mats that have been specifically designed as

electrical insulators.

– Use a grounded wrist strap designed to prevent static discharge.

– Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready

for use.

– Touch a grounded metal object before removing the board from the antistatic bag.

– Do not let components or printed circuit boards come into contact with your clothing,

which may retain a charge even if you are wearing a wrist strap.

– Handle a board by its edges only. Do not touch its components, peripheral chips, memory

modules or contacts.

– When handling chips or modules, avoid touching their pins.

– Put the mainboard and peripherals back into their antistatic bags when not in use.

– For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and the

mainboard.

Operating precautions

The chassis cover must be in place when the system is operating to assure proper cooling. Out

of warranty damage to the system can occur if this practice is not strictly followed.

1.3

1.4

6en | Safety precautions DIVAR IP 7000 2U

2013.05 | V1 | DOC Quick Installation Guide Bosch Sicherheitssysteme GmbH

Note:

Please handle used batteries carefully. Do not damage the battery in any way. A damaged

battery may release hazardous materials into the environment. Do not discard a used battery

in the garbage or a public landfill. Please comply with the regulations set up by your local

hazardous waste management agency to dispose of your used battery properly.

Important notices

Accessories - Do not place this unit on an unstable stand, tripod, bracket,

or mount. The unit may fall, causing serious injury and/or serious damage to

the unit. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer. When a cart is used, use caution and care when moving

the cart/apparatus combination to avoid injury from tip-over. Quick stops,

excessive force, or uneven surfaces may cause the cart/unit combination to

overturn. Mount the unit per the manufacturer's instructions.

FCC and ICES compliance

(only for U.S.A. and Canada)

This equipment has been tested and found to comply with the limits for a Class A digital

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the manufacturer’s instruction manual, may cause

harmful interference with radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference, in which case you will be required to correct the

interference at your own expense.

1.5

1.6

DIVAR IP 7000 2U Safety precautions | en 7

Bosch Sicherheitssysteme GmbH Quick Installation Guide 2013.05 | V1 | DOC

System overview

DIVAR IP 7000 is an affordable, simple and reliable all-in-one recording, viewing and

management solution for network surveillance systems of up to 64 channels (with 32 channels

pre-licensed). Running the full Bosch VMS (Video Management System) solution and powered

by Bosch VRM (Video Recording Manager) software, the DIVAR IP 7000 is an intelligent IP

storage device that eliminates the need for separate NVR (Network Video Recorder) server and

storage hardware.

The 2U rack mount unit combines advanced management and state-of-the-art recording

management into a single cost-effective, plug and play IP recording appliance for IT-minded

customers which are seeking for a state-of-the-art “second generation” NVR recording

solution.

DIVAR IP 7000 features:

– Instant real time access to video

View high quality HD video despite low or limited bandwidth connections. Dynamic

Transcoding technology ensures that you can view your video immediately — anytime,

anywhere.

– Easy installation

DIVAR IP 7000 2U features wizard based set-up and centralized configuration to reduce

installation times. All components are pre-installed and pre-configured. Simply connect to

the network and turn on the unit — DIVAR IP 7000 2U starts recording straight out of the

box.

– Access to Bosch VMS

After starting the system, immediate access to the Bosch VMS management application is

offered by a customized user interface. The ability to use one central user interface for

configuration and operation management reduces installation and training requirements,

and helps to keep ongoing system management costs low.

Front view:

34 7

1Power Failure 5Power

2Overheat/Fan Fail 6Reset

3NIC1/NIC2 7Power on/off

4HDD

8en | System overview DIVAR IP 7000 2U

2013.05 | V1 | DOC Quick Installation Guide Bosch Sicherheitssysteme GmbH

Rear view:

267

12x mains connection 100 – 240 VAC,

50 - 60 Hz

5Monitor (VGA)

22x PS/2 (mouse and keyboard) 62x NIC

32x USB 7Slots for:

– 1x graphic card (1x Display Port,

1x DVI)

– 1x sound card

– 2x USB 2.0

4Serial interface COM1

DIVAR IP 7000 2U System overview | en 9

Bosch Sicherheitssysteme GmbH Quick Installation Guide 2013.05 | V1 | DOC

System setup - hardware

Introduction

Scope of delivery:

– DIVAR IP 7000 – 8-bay system, fully equipped with 8 hard drives (DIP-7082-8HD)

– In addition to the system itself, the following items should have been shipped along with

each system

– One rackmount kit

– One AC power cable for each power supply in the system

– This quick install guide

Unpacking the system

You should inspect the box the chassis was shipped in and note if it was damaged in any way.

If the chassis itself shows damage, file a damage claim with the carrier who delivered it and

notify the respective Bosch RMA desk.

You will also need it placed near at least one grounded power outlet.

Due to the weight of the system: After opening the top of the shipping box, one person should

stand at either end and lift the disk array out together.

Be sure to read the safety precautions.

Preparing for setup

The box the system is shipped in includes a rack mount kit, which you will need to install the

system into the rack.

Follow the steps in the order given to complete the installation process in a minimum amount

of time. Read this section before you begin the installation procedure outlined in the sections

that follow.

Choosing a setup location

– Situate the system in a clean, dust-free area that is well ventilated. Avoid areas where

heat, electrical noise and electromagnetic fields are generated. Place the system near a

grounded power outlet.

– Leave approximately 25 inches clearance in front of the rack to be able to open the front

door completely.

– Leave approximately 30 inches of clearance in the back of the rack to allow for sufficient

airflow and ease in servicing.

– Install the system only in a Restricted Access Location (dedicated equipment rooms,

service closets and the like).

Notice!

This product is not suitable for use with visual display work place devices acccording to §2 of

the the German Ordinance for Work with Visual Display Units.

Rack precautions

Warning!

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special

precautions to ensure that the system remains stable. The following guidelines are provided

to ensure your safety:

3.1

3.2

3.3

3.3.1

3.3.2

10 en | System setup - hardware DIVAR IP 7000 2U

2013.05 | V1 | DOC Quick Installation Guide Bosch Sicherheitssysteme GmbH

Andere Handbücher für DIVAR IP 7000 2U

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bosch Netzwerk-Hardware Handbücher

Bosch

Bosch DIVAR IP 3000 DIP-3040-00N Bedienungsanleitung

Bosch

Bosch VideoJet X SN Bedienungsanleitung

Bosch

Bosch NPD-6001A Bedienungsanleitung

Bosch

Bosch VIP X1600 Module Bedienungsanleitung

Bosch

Bosch VIP X1600 Module Bedienungsanleitung

Bosch

Bosch Rexroth NK350 Bedienungsanleitung

Bosch

Bosch DIVAR IP 6000 1U Bedienungsanleitung

Bosch

Bosch VIP X1600 Module Bedienungsanleitung

Bosch

Bosch VideoJet X10 SN Bedienungsanleitung

Bosch

Bosch PHANTOM EDGE Bedienungsanleitung

Bosch

Bosch VIP-X1XF Bedienungsanleitung

Bosch

Bosch VideoJet X10/X20/X40 Bedienungsanleitung

Bosch

Bosch VIPX1A Bedienungsanleitung

Bosch

Bosch RTS RVON+ Bedienungsanleitung

Bosch

Bosch VIDEOJET X40 Montageanleitung

Bosch

Bosch DIVAR IP all-in-one 6000 Bedienungsanleitung

Bosch

Bosch DLA-AIOL0 Bedienungsanleitung

Bosch

Bosch VIP X1 Bedienungsanleitung

Bosch

Bosch VideoJet 8008 Bedienungsanleitung

Bosch

Bosch VideoJet 8008 Bedienungsanleitung

Bosch

Bosch VIP X1 Bedienungsanleitung

Bosch

Bosch DIVAR IP 6000 (2U) Bedienungsanleitung

Bosch

Bosch LTC 4600 Series Bedienungsanleitung

Bosch

Bosch DVRXEAP01 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung