Bosch LE10 Bedienungsanleitung

LE10 Radio Receiver

CRS-URE-0100 | F.01U.278.517 | V2.0 | 2012.11

en User Manual

LE10 Radio Receiver Table of Contents | en 3

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

Table of Contents

1 Safety instructions 5

1.1 General safety instructions 5

1.2 Environmental conditions 5

1.3 Electrostatic Discharge (ESD) 5

2 Product information 6

2.1 General description 6

2.2 Compatible transmitters 6

2.3 Main applications 7

2.4 Description of the different modes 7

3 Installation 9

3.1 Unpacking 9

3.2 Connecting the power supply 9

3.2.1 Power supply with the RJ12 power socket 9

3.2.2 Power supply connected to a wired installation 9

3.3 Wall installation 10

4 Connection compartment 11

4.1 Connecting ports 11

4.2 Mode selection 12

4.2.1 Mode indication after power on 12

5 Programming 13

5.1 Enter programming mode 13

5.2 Program a transmitter in modes 1, 2 or 5 13

5.3 Delete a transmitter 14

5.4 Delete all transmitters 14

5.5 Program a door address in modes 3 or 4 15

5.5.1 Programming in modes 6 or 7 15

6Operation 16

6.1 Standby mode 16

6.1.1 Standby with no transmitter programmed 16

6.1.2 Standby with at least one transmitter programmed 16

4en | Table of Contents LE10 Radio Receiver

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

6.2 Normal mode (modes 1 and 2) 16

6.2.1 Activation of a transmitter in normal mode 16

6.3 Dementia (mode 3) 17

6.3.1 Activation of a MIYS37L Wristband Transmitter 17

6.3.2 Detection of a MIYS37E Wristband Transmitter alone 18

6.3.3 Detection of a MIYS37L Wristband Transmitter with a MIYS37E

Wristband Transmitter nearby 18

6.4 Dementia with Accompany (mode 4) 19

6.4.1 Activation of a MIYS37L Wristband Transmitter 19

6.5 Remote control (mode 5) 19

6.5.1 Activation of a programmed transmitter 19

6.5.2 Activation of a programmed transmitter with a battery-low

message or with a new battery 20

6.6 Open receiver (modes 6 and 7) 20

6.6.1 Activation of a transmitter in the reception range 20

6.7 Daily messages in modes 1, 2 or 5 20

6.7.1 Daily message with battery-low signal 20

6.7.2 Reset of a battery-low indication with button T1 21

6.8 Extended MIYN46 (mode 8, only with SW 1.10) 21

6.9 Dual channel receiver (mode 9, only with SW 1.10) 22

7 Technical data 23

LE10 Radio Receiver Safety instructions | en 5

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

1 Safety instructions

1.1 General safety instructions

Installation and initial operation should only be carried out by

trained service personnel.

1.2 Environmental conditions

The LE10 Radio Receiver must not be located near a water tap

or any other source of water. The electrical safety of the LE10

Radio Receiver is only guaranteed if the electrical installation is

in accordance with the national regulations and if this

installation works properly. The LE10 Radio Receiver may not

be used in buildings prone to fire and explosion hazards.

The LE10 Radio Receiver may not be used under exposure to

direct sunlight, to heat, to dust or to an excessive humidity

(only use the equipment in a clean environment).

1.3 Electrostatic Discharge (ESD)

WARNING!

The LE10 Radio Receiver contains highly sensitive electronic

components. It should be opened only in an ESD protected

environment with respect to the following precautions.

Discharge yourself from electrostatic loads by touching a

grounded conductive surface before opening the unit. Avoid

touching conductive parts inside the LE10 Radio Receiver if not

absolutely necessary.

6en | Product information LE10 Radio Receiver

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

2 Product information

2.1 General description

The LE10 Radio Receiver is designed to receive radio signals

from different Bosch radio transmitters at the frequency of

434.01 MHz. After receiving radio signals from either

programmed or not programmed wireless transmitters, the

LE10 Radio Receiver reacts by activating its two green and red

LEDs and by switching relay outputs of two relays.

Figure 2.1 Front view of the LE10 Radio Receiver

2.2 Compatible transmitters

All of the following Bosch wireless transmitters are compatible

with the LE10 Radio Receiver:

– MIYS37 Wristband Transmitters

– MIYS37L Wristband Transmitters with Locating function

– MIYS37E Wristband Transmitters with Accompany function

– MIYS35 Pendant Transmitters

– MIYMD ManDown Sensors

– MIYRAC Wireless Contact

LED 1 (green)

LED 2 (red)

LE10 Radio Receiver Product information | en 7

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

2.3 Main applications

LE10 Radio Receiver as small stand alone call system

After receiving a radio signal from a programmed radio

transmitter, the relay output switches a siren or a lamp to

indicate locally a wireless call.

LE10 Radio Receiver connected to a emergency call system

via relay contact

After receiving a radio signal from a programmed radio

transmitter, the relay will be switched. This relay output is

connected to a wired emergency call system by wire and hereby

a call will be generated or forwarded.

LE10 Radio Receiver as part of a Resident Alert System

monitoring dementia

After receiving a signal from a dementia transmitter, the relay

will be activated to close a monitored door.

2.4 Description of the different modes

Mode Name Description

1 Normal 20 wireless transmitters can be programmed.

Calls are indicated by the red LED and Relay 1.

A battery-low signal is indicated by the red

LED and Relay 2.

2 Normal, with red LED

deactivated at

battery-low indication

The same functions as in mode 1 are available,

except for the battery-low signal which is not

indicated by the red LED, but only by Relay 2.

3 Dementia The MIYS37L and MIYS37E wireless

transmitters are detected. Relay 1 can be used

to lock a monitored door. Relay 2 can be used

to interrupt a monitoring loop.

8en | Product information LE10 Radio Receiver

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

4 Dementia with

Accompany

This mode allows to connect the LE10 Radio

Receiver to a wired emergency call system, in

which the Accompany function can be

implemented. It will wait 10 seconds after

receiving a signal from a MIYS37L transmitter.

If it detects a MIYS37E transmitter in this lapse

of time, no alarm is generated. If not, Relay 1 is

activated for 2 seconds.

5 Remote control 20 wireless transmitters can be programmed.

Per sequence, only the same transmitter can

switch on and off the Relay1. A battery-low

signal is indicated by the red LED and Relay 2.

6 Open receiver No wireless transmitter needs to be

programmed. Any transmitter within reception

range of the LE10 Radio Receiver can activate

the device.

7 Open receiver with

reduced range

Same functions as in mode 6, but with

reduced range. This functionality is designed

to improve reception of transmitters located

closer to the LE10 Radio Receiver.

8 Extended MIYN46

transmitter

programming

(only with SW 1.10)

Additional MIYN46 transmitters can be

programmed. Behavior is similar to normal

mode 1, with certain differences according to

the transmitter that is activated.

9 Dual channel receiver

(only with SW 1.10)

Only MIYS37 wireless transmitters can be

programmed. Calls are indicated by Relay 1 or

Relay 2, according to the slot in which the

MIYS37 wireless transmitter is programmed. A

battery-low signal is indicated by the red LED.

Mode Name Description

NOTICE!

Factory setting is normal mode 1, in which 20 wireless

transmitters can be programmed. Calls are indicated by the red

LED and Relay 1. A battery-low signal is indicated by the red

LED and Relay 2.

LE10 Radio Receiver Installation | en 9

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

3 Installation

3.1 Unpacking

The LE10 Radio Receiver is carefully packed for transportation.

The components contained in the box are protected, but should

be handled with care. Store the packaging material for further

use (storage or transport). In case of defective or missing

equipment, do not try to install the LE10 Radio Receiver.

Contact immediately your local representative.

1. Take all components out of the box and place the LE10 Radio

Receiver on the working space.

2. Check that the following accessories are delivered: the

fixings (2 screws and 2 screw anchors) and this user manual.

3. Check that the LE10 Radio Receiver and its accessories have

not been damaged during transportation.

3.2 Connecting the power supply

There are two different ways to connect the power supply of

the LE10 Radio Receiver. After connection, the LE10 Radio

Receiver will be in standby mode.

3.2.1 Power supply with the RJ12 power socket

The LE10 Radio Receiver can be powered by a power supply

unit (PSU). The PSU should be plugged in the RJ12 socket on

the rear side of the unit and should be easily accessible at any

time. See Section 4.1 Connecting ports, page 11 for access to

the socket. See Section 7 Technical data, page 23 for

information about the power supply.

3.2.2 Power supply connected to a wired installation

The LE10 Radio Receiver can be powered by connecting a wired

input into poles 1 and 2 of the connection board. See

Section 4.1 Connecting ports, page 11 for information about the

power supply.

10 en | Installation LE10 Radio Receiver

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

3.3 Wall installation

You can fasten the LE10 Radio Receiver on a smooth wall

surface using two screws. Installation cables should be placed

inside the cable channels on the bottom.

Figure 3.1 Dimensions of the backside of the LE10 Radio Receiver

3.4 in (80 mm)

Ø0.3in

(7.5 mm)

2.2 in (53.8 mm)

0.51 in

(13.1 mm) 0.15 in

(3.7 mm)

0.63 in (16 mm)

0.26 in (6.6 mm)

2.36 in (59.9 mm)

1.06 in (27 mm

0.71 in (18.1 mm)

5.16 in (131 mm)

0.08 in

(2 mm)

1.62 in

(26 mm) 0.15 in

(3.7 mm)

Andere Handbücher für LE10

Inhaltsverzeichnis

Andere Bosch Empfänger Handbücher

Bosch

Bosch Coach smartPanel NAFTA 7 620 210 046 Technisches Handbuch

Bosch

Bosch FA400 Bedienungsanleitung

Bosch

Bosch LR 2 Professional Bedienungsanleitung

Bosch

Bosch LR 6 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Bosch

Bosch LR 1 Professional Bedienungsanleitung

Bosch

Bosch Radion B810 Bedienungsanleitung

Bosch

Bosch LTC 8561 Series Bedienungsanleitung

Bosch

Bosch RFRC-OPT Bedienungsanleitung

Bosch

Bosch Radion B810 Bedienungsanleitung

Bosch

Bosch Radion B810 Bedienungsanleitung

Bosch

Bosch BLE 130 Professional Bedienungsanleitung

Bosch

Bosch LR30 Bedienungsanleitung

Bosch

Bosch RFRC-OPT Bedienungsanleitung

Bosch

Bosch ISW-EN4216R Bedienungsanleitung

Bosch

Bosch Conettix D6600 Betriebsanleitung

Bosch

Bosch RF3212E Bedienungsanleitung

Bosch

Bosch Professional GCT 30-42 Bedienungsanleitung

Bosch

Bosch LR 1 Professional Bedienungsanleitung

Bosch

Bosch LR 2 Professional Bedienungsanleitung

Bosch

Bosch EN4216R Bedienungsanleitung

Bosch

Bosch WE800EV2 RF Bedienungsanleitung

Bosch

Bosch RE005EV2 Bedienungsanleitung

Bosch

Bosch LE10 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung

Dish Network

Dish Network Satellite Television Bedienungsanleitung