Bosch LR 6 Bedienungsanleitung

Operating / Safety Instructions

Consignes d’utilisation / de sécurité

Instrucciones de funcionamiento y seguridad

LR 6

IMPORTANT:

Read Before Using

IMPORTANT :

Lire avant usage

IMPORTANTE:

Leer antes de usar

English Version

See page 5

Version française

Voir page 15

Versión en español

Ver la página 25

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

LR6

Professional

LR6

Professional

Call Toll Free for Consumer Information & Service Locations

Pour obtenir des informations et les adresses de nos centres de

service après-vente, appelez ce numéro gratuit

Llame gratis para obtener información para el consumidor y

ubicaciones de servicio

-2-

LR6

Professional

LR 6

1 618 C01 18C

-3-

LR6

Professional

-4-

General Safety Rules

Read all instructions. Failure to follow all instruc-

tions listed below may result in electric shock,

ﬁre and/or serious injury.

SAVE THESE INSTRUCTIONS

Work area safety

Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

DO NOT operate the laser tool around children or allow chil-

dren to operate the laser tool. Serious eye injury could result.

Electrical safety

Batteries can explode or leak, cause injury or

ﬁre. To reduce this risk, always follow all in-

structions and warnings on the battery label and package.

DO NOT short any battery terminals.

DO NOT charge alkaline batteries.

DO NOT mix old and new batteries. Replace all of them at the

same time with new batteries of the same brand and type.

DO NOT mix battery chemistries. Dispose of or recycle batter-

ies per local code.

DO NOT dispose of batteries in ﬁre.

Keep batteries out of reach of children.

Remove batteries if the device will not be used for several

months.

FCC Statement

Changes or modiﬁcations to this unit not

expressly approved by the party responsible

for compliance could void the user’s authority to operate the

equipment.

Note: This product has been tested and found to comply with the

limits for a Class B Digital device, pursuant to Part 15 of the FCC

-5-

Rules. These limits are designed to provide reasonable protec-

tion against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can

be determined by turning the equipment oﬀ and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit diﬀerent from

that to which the receiver is connected.

– Consult the dealer or an experienced radio TV technician for

help.

Personal safety

Stay alert, watch what you are doing and use

common sense when operating a tool. Do not

use a tool while you are tired or under the inﬂuence of drugs,

alcohol or medication. A moment of inattention while operating

a tool may result in serious personal injury or incorrect measure-

ment results.

Use safety equipment. Always wear eye protection. Safety

equipment such as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

Keep the measuring tool away from cardiac pace-

makers. The magnet plate 10 generates a ﬁeld that

can impair the function of cardiac pacemakers.

Keep the measuring tool away from magnetic data medium and

magnetically-sensitive equipment. The eﬀect of the magnet plate

10 can lead to irreversible data loss.

-6-

Noise Information

The A-weighted sound pressure level of the audio signal at one

meter distance is 80 dB(A).

Do not hold the tool close to your ear!

Use and care

Use the correct tool for your application. The

correct tool will do the job better and safer.

Do not use the tool if the switch does not turn it on and oﬀ. Any

tool that cannot be controlled with the switch is dangerous and

must be repaired.

Store idle tool out of the reach of children and do not allow

persons unfamiliar with the tool or these instructions to oper-

ate the tool. Tools are dangerous in the hands of untrained users.

Maintain tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may af-

fect the operation. If damaged, tool repaired before use. Many

accidents are caused by poorly maintained tools.

Use the tool, accessories, etc., in accordance with these in-

structions and in the manner intended for the particular type of

tool, taking into account the working conditions and the work

to be performed. Use of the tool for operations diﬀerent from

those intended could result in a hazardous situation.

Service

Have your tool serviced by a qualiﬁed repair person using only

identical replacement parts. This will ensure that the safety of

the tool is maintained.

Develop a periodic maintenance schedule for tool. When clean-

ing a tool be careful not to disassemble any portion of the tool

since internal wires may be misplaced or pinched or may be

improperly mounted. Certain cleaning agents such as gasoline,

carbon tetrachloride, ammonia, etc. may damage plastic parts.

SAVE THESE INSTRUCTIONS.

-7-

Intended Use

The tool is intended for detecting pulsating line lasers.

Preparation

Inserting/Replacing the Battery

Alkaline batteries are recommended for the tool.

Pull the latch 16 of battery lid outward and open the battery lid 15.

When inserting batteries, pay attention to the correct polarity.

When the batteries become weak, the LED indicator 3will begin

to ﬂash. It is still possible to work with the measuring tool.

Remove the batteries from the tool when not

using it for extended periods. When storing

for extended periods, the batteries can corrode and discharge

themselves.

Features

The numbering of the product features shown refers to the illustra-

tion of the tool on the graphic page.

1Accuracy Button

2On/Oﬀ button

3Power indicator/Battery

warning

4Audio signal button

5Speaker

6Direction LED “move

upward”

7Center-indication LED

8Direction LED “move

downward”

9Reception area for the

laser beam

10 Magnets

11 Guide groove for

mounting bracket

12 Center mark

13 Type plate

14 Serial number

15 Battery lid

16 Latch of battery lid

17 Mounting bracket

18 Rotary knob of the

mounting bracket

19 Guide rail

20 Mounting bracket latch

21 Push-button to release

the lock

-8-

Laser Receiver.................................................LR 6

Article number ...................................... 3 601 K69 H10

Working range1) .................................... 16’-164’ (5-50 m)

Receiving angle ................................................ 90°

Measuring accuracy2)

– “Fine” adjustment ..................................±1/32” (±1 mm)

– “Coarse” adjustment .................................±1/8” (±3 mm)

Operating temperature ..................14 °F....+122 °F (-10 °C...+50 °C)

Storage temperature .....................-4 °F...+158 °F (-20 °C...+70 °C)

Batteries ........................................2 x1.5V LR03 (AAA)

Operating time, approx. .........................................30 h

Weight ............................................0.26 lb (0.12 kg)

Degree of protection ...........................................IP 54

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(dust and splash water protected)

Dimensions (length x width x height) ....................2.7” x 1.1” x 4.8”

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(69 x 28 x 123 mm)

1) The working range can be decreased by unfavorable environmental

conditions (e.g. direct sun exposure).

2) The angular accuracy between the 45° laser line and the 90° laser line

is max. ±5/32” @ 30 ft (±0.4 mm/m).

Please observe the article number on the type plate of your tool.

The trade names of the individual tools may vary.

The tool can be clearly identified with the serial number 14 on the type

plate.

Technical Data

-9-

Operation

Initial Operation

• Protect the tool against moisture.

• Do not subject the tool to extreme temperatures or variations

in temperature. As an example, do not leave it in vehicles for

longer periods. In case of large variations in temperature, allow

the tool to adjust to the ambient temperature before putting it

into operation. In case of extreme temperatures or variations in

temperature, the accuracy of the tool can be impaired.

DO NOT stare directly at the laser beam or project

the laser beam directly into the eyes of others.

Serious eye injury could result.

Setting Up the Tool (see ﬁgure A)

Position the tool at least 17 ft (5 m) away from the cross-line

laser. Switch on the pulsating function of the cross-line laser and

select horizontal or vertical operation.

Note: Do not select cross-line operation or else faulty indications

on the height of the laser beam can occur.

Position the tool in such a manner that the laser beam can reach

the reception area 9. Align the tool in such a manner that the la-

ser beam runs horizontally through the reception area (as shown

in the ﬁgure).

Switching On and Oﬀ

• A loud audio signal sounds when switching on the tool.

Therefore, keep the tool away from your ear or other people

when switching on. The loud audio signal can cause hearing

defects.

To switch on the tool, press the On/Oﬀ button 2. An audio signal

will sound and all LEDs will light up brieﬂy.

To switch oﬀ the tool, press the On/Oﬀ button 2again. An audio

signal will sound three times and all LEDs will light up brieﬂy

before the tool switches oﬀ. The power indicator 3turns oﬀ.

-10-

When no button is pressed on the tool for approx. 20 minutes

and when no laser beam reaches the reception area 9for 20

minutes, the tool automatically switches oﬀ in order to save

battery power.

Selecting the Setting of the Center Indicator

With button 1, you can specify with which accuracy the position

of the laser beam is indicated on the reception area:

– “Fine” adjustment (the centre-indication LED 7ﬂashes),

– “Coarse” adjustment (the LED direction indicators 8and 6

ﬂash).

Whenever switching on the tool, the accuracy level “Fine” is set.

Direction Indicators

The position of the laser beam on the reception area 9is indi-

cated:

– via the LEDs “move downward” 8, “move upward” 6or the

center-indication LED 7on the front and back of the tool,

– optionally via the audio signal (see “Audio Signal for Indication

of the Laser Beam”).

Tool too low: When the laser beam runs through the top half of

the reception area 9, the corresponding direction LED 6lights

up. When the audio signal is switched on, a high frequency signal

sounds. Move the tool upward in the direction of the arrow.

Tool too high: When the laser beam runs through the bottom half

of the reception area 9, the corresponding direction LED 8lights

up. When the audio signal is switched on, a low frequency signal

sounds. Move the tool downward in the direction of the arrow.

Tool in center position: When the laser beam runs through the

reception area 9at the center mark 12, the corresponding center-

indication LED 7lights up. When the audio signal is switched on,

a continuous signal sounds.

Inhaltsverzeichnis

Sprachen:

Andere Bosch Empfänger Handbücher

Bosch

Bosch LE10 Bedienungsanleitung

Bosch

Bosch ISW-EN4216R Bedienungsanleitung

Bosch

Bosch WE800EV2 RF Bedienungsanleitung

Bosch

Bosch BLE 130 Professional Bedienungsanleitung

Bosch

Bosch LR30 Bedienungsanleitung

Bosch

Bosch LR 1 Professional Bedienungsanleitung

Bosch

Bosch Coach smartPanel NAFTA 7 620 210 046 Technisches Handbuch

Bosch

Bosch LE10 Bedienungsanleitung

Bosch

Bosch Professional GCT 30-42 Bedienungsanleitung

Bosch

Bosch RF3212E Bedienungsanleitung

Bosch

Bosch RFRC-OPT Bedienungsanleitung

Bosch

Bosch LR 2 Professional Bedienungsanleitung

Bosch

Bosch RFRC-OPT Bedienungsanleitung

Bosch

Bosch EN4216R Bedienungsanleitung

Bosch

Bosch Professional LR 60 Bedienungsanleitung

Bosch

Bosch LTC 8561 Series Bedienungsanleitung

Bosch

Bosch Radion B810 Bedienungsanleitung

Bosch

Bosch GML 10,8 V-LI Bedienungsanleitung

Bosch

Bosch RE005EV2 Bedienungsanleitung

Bosch

Bosch LR 2 Professional Bedienungsanleitung

Bosch

Bosch RFRC-OPT Bedienungsanleitung

Bosch

Bosch RF3224 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Bosch

Bosch RE005EV2 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung

Dish Network

Dish Network Satellite Television Bedienungsanleitung