Bosch DIVAR DIP-6080-00N Bedienungsanleitung
DIVAR IP 6000 2U
DIP-6080-00N, DIP-6082-8HD
en Quick Installation Guide
Table of contents
1Safety precautions 4
1.1 General safety precautions 4
1.2 Electrical safety precautions 5
1.3 ESD precautions 6
1.4 Operating precautions 6
1.5 Important notices 7
1.6 FCC and ICES compliance 7
2System overview 8
2.1 System interface 8
3System setup - hardware 10
3.1 Introduction 10
3.2 Unpacking the system 10
3.3 Preparing for setup 10
3.3.1 Choosing a setup location 10
3.3.2 Rack precautions 10
3.3.3 General system precautions 11
3.3.4 Rack mounting considerations 11
3.4 Rack mounting instructions 12
3.4.1 Separating the sections of the rack rails 12
3.4.2 Installing the inner rails 13
3.4.3 Installing the outer rails to the rack 13
3.4.4 Installing the chassis into the rack 14
3.4.5 Installing the chassis into a Telco rack 15
3.5 Turning on the system 15
4System Setup – first Steps 16
4.1 Introduction 16
4.2 Setup instruction 16
4.3 Setting the IP address 16
4.3.1 Remote desktop connection 16
4.3.2 Physical connection 19
4.4 VRM Appliance 21
4.4.1 Default installation 21
4.4.2 Disabling the VRM service 21
4.5 Standard system configuration 21
5Additional software and documentation 22
6Service and repair 23
DIVAR IP 6000 2U Table of Contents | en 3
Bosch Sicherheitssysteme GmbH Quick Installation Guide 2013.05 | V3 | DOC
Safety precautions
Observe the safety precautions in this chapter.
General safety precautions
Follow these rules to ensure general safety:
– Keep the area around the system clean and free of clutter.
– Place the chassis top cover and any system components that have been removed away
from the system or on a table so that they won't accidentally be stepped on.
– While working on the system, do not wear loose clothing such as neckties and
unbuttoned shirt sleeves, which can come into contact with electrical circuits or be
pulled into a cooling fan.
– Remove any jewelry or metal objects from your body, which are excellent metal
conductors that can create short circuits and harm you if they come into contact with
printed circuit boards or areas where power is present.
– After accessing the inside of the system, close the system back up and secure it to the
rack unit after ensuring that all connections have been made.
– The system weighs approximately 57 lbs. (25.9 kg) when fully loaded. When lifting the
system, two people at either end should lift slowly with their feet spread out to distribute
the weight. Always keep your back straight and lift with your legs.
!
Warning!
Interruption of mains supply:
Voltage is applied as soon as the mains plug is inserted into the mains socket.
However, for devices with a mains switch, the device is only ready for operation when the
mains switch (ON/OFF) is in the ON position. When the mains plug is pulled out of the
socket, the supply of power to the device is completely interrupted.
!
Warning!
Removing the housing:
To avoid electric shock, the housing must only be removed by qualified service personnel.
Before removing the housing, the plug must always be removed from the mains socket and
remain disconnected while the housing is removed. Servicing must only be carried out by
qualified service personnel. The user must not carry out any repairs.
!
Warning!
Power cable and AC adapter:
When installing the product, use the provided or designated connection cables, power cables
and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire.
Electrical Appliance and Material Safety Law prohibits the use of UL or CSA-certified cables
(that have UL/CSA shown on the code) for any other electrical devices.
1
1.1
4en | Safety precautions DIVAR IP 6000 2U
2013.05 | V3 | DOC Quick Installation Guide Bosch Sicherheitssysteme GmbH
!
Warning!
Lithium battery:
Batteries that have been inserted wrongly can cause an explosion. Always replace empty
batteries with batteries of the same type or a similar type recommended by the manufacturer.
Handle used batteries carefully. Do not damage the battery in any way. A damaged battery
may release hazardous materials into the environment.
Dispose of empty batteries according to the manufacturer's instructions.
!
Warning!
Handling of lead solder materials used in this product may expose you to lead, a chemical
known to the State of California to cause birth defects and other reproductive harm.
Notice!
Electrostatically sensitive device:
To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried
out correctly.
When handling electrostatically sensitive printed circuits, grounded anti-static wrist bands
must be worn and the ESD safety precautions observed.
Notice!
Installation should only be carried out by qualified customer service personnel in accordance
with the applicable electrical regulations.
Disposal
Your Bosch product has been developed and manufactured using high-
quality materials and components that can be reused.
This symbol means that electronic and electrical devices that have reached
the end of their working life must be disposed of separately from
household waste.
In the EU, separate collecting systems are already in place for used
electrical and electronic products. Please dispose of these devices at your
local communal waste collection point or at a recycling center.
Electrical safety precautions
Basic electrical safety precautions should be followed to protect you from harm and the
system from damage:
– Be aware of the locations of the power on/off switch on the chassis as well as the room's
emergency power-off switch, disconnection switch or electrical outlet. If an electrical
accident occurs, you can then quickly remove power from the system.
– Do not work alone when working with high voltage components.
– Power should always be disconnected from the system when removing or installing main
system components, such as the motherboard or memory modules. When disconnecting
power, you should first turn off the system and then unplug the power cords from all the
power supply modules in the system.
– When working around exposed electrical circuits, another person who is familiar with the
power-off controls should be nearby to switch off the power if necessary.
1.2
DIVAR IP 6000 2U Safety precautions | en 5
Bosch Sicherheitssysteme GmbH Quick Installation Guide 2013.05 | V3 | DOC
– Use only one hand when working with powered-on electrical equipment. This is to avoid
making a complete circuit, which will cause electrical shock. Use extreme caution when
using metal tools, which can easily damage any electrical components or circuit boards
they come into contact with.
– The power supply power cords must include a grounding plug and must be plugged into
grounded electrical outlets. The unit has more than one power supply cord. Disconnect
both power supply cords before servicing to avoid electrical shock.
– Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Temperature
Coefficient) fuses on the mainboard must be replaced by trained service technicians only.
The new fuse must be the same or equivalent as the one replaced. Contact technical
support for details and support.
!
Caution!
Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside
down, which will reverse its polarities. This battery must be replaced only with the same or
an equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries
according to the manufacturer's instructions.
!
Caution!
DVD-ROM Laser: This system comes without a DVD-ROM drive but if added: To prevent direct
exposure to the laser beam and hazardous radiation exposure, do not open the enclosure or
use the unit in any unconventional way.
ESD precautions
Electrostatic Discharge (ESD) is generated by two objects with different electrical charges
coming into contact with each other. An electrical discharge is created to neutralize this
difference, which can damage electronic components and printed circuit boards. The
following measures are generally sufficient to neutralize this difference before contact is made
to protect your equipment from ESD:
– Do not use mats designed to decrease electrostatic discharge as protection from
electrical shock. Instead, use rubber mats that have been specifically designed as
electrical insulators.
– Use a grounded wrist strap designed to prevent static discharge.
– Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready
for use.
– Touch a grounded metal object before removing the board from the antistatic bag.
– Do not let components or printed circuit boards come into contact with your clothing,
which may retain a charge even if you are wearing a wrist strap.
– Handle a board by its edges only. Do not touch its components, peripheral chips, memory
modules or contacts.
– When handling chips or modules, avoid touching their pins.
– Put the mainboard and peripherals back into their antistatic bags when not in use.
– For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and the
mainboard.
Operating precautions
The chassis cover must be in place when the system is operating to assure proper cooling. Out
of warranty damage to the system can occur if this practice is not strictly followed.
1.3
1.4
6en | Safety precautions DIVAR IP 6000 2U
2013.05 | V3 | DOC Quick Installation Guide Bosch Sicherheitssysteme GmbH
Note:
Please handle used batteries carefully. Do not damage the battery in any way. A damaged
battery may release hazardous materials into the environment. Do not discard a used battery
in the garbage or a public landfill. Please comply with the regulations set up by your local
hazardous waste management agency to dispose of your used battery properly.
Important notices
Accessories - Do not place this unit on an unstable stand, tripod, bracket,
or mount. The unit may fall, causing serious injury and/or serious damage to
the unit. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer. When a cart is used, use caution and care when moving
the cart/apparatus combination to avoid injury from tip-over. Quick stops,
excessive force, or uneven surfaces may cause the cart/unit combination to
overturn. Mount the unit per the manufacturer's instructions.
FCC and ICES compliance
(only for U.S.A. and Canada)
This equipment has been tested and found to comply with the limits for a Class A digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the manufacturer’s instruction manual, may cause
harmful interference with radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case you will be required to correct the
interference at your own expense.
1.5
1.6
DIVAR IP 6000 2U Safety precautions | en 7
Bosch Sicherheitssysteme GmbH Quick Installation Guide 2013.05 | V3 | DOC
System overview
DIVAR IP 6000 is an affordable, simple and reliable all-in-one recording management solution
for network surveillance systems of up to 64 cameras. Powered by VRM (Video Recording
Manager) software, the system is an intelligent IP storage device that eliminates the need for
separate NVR (Network Video Recorder) server and storage hardware.
The system is a 2U rack mount unit that combines advanced recording management and state-
of-the-art iSCSI storage into a single cost-effective, plug and play IP recording appliance for IT-
minded customers seeking for a state-of-the-art “second generation” NVR recording solution.
DIVAR IP 6000 features:
– Instant real time access to video
View high quality HD video despite low or limited bandwidth connections. Dynamic
Transcoding technology ensures that you can view your video immediately — anytime,
anywhere.
– Remote viewing
DIVAR IP 6000 comes with our advanced Video Client for remote viewing. Video Client is a
Windows PC application for live viewing and playback including Configuration Manager.
Configuration Manager allows the settings of the DIVAR IP 6000 be configured. A stand-
alone archive player will allow archive playback and authentication without any other
workstation software.
System interface
There are several LEDs on the front and rear of the chassis. The LEDs show the over-all status
of the system and the activity and health of specific components.
Front view:
1Power Failure 5Power
2Overheat/Fan Fail 6Reset
3NIC1/NIC2 7Power on/off
4HDD
2
2.1
8en | System overview DIVAR IP 6000 2U
2013.05 | V3 | DOC Quick Installation Guide Bosch Sicherheitssysteme GmbH
Rear view:
26
15
34
12x mains connection 100 – 240 VAC,
50 - 60 Hz
4Serial interface COM1
22x PS/2 5Monitor (VGA)
32x USB 62x Ethernet (RJ45)
DIVAR IP 6000 2U System overview | en 9
Bosch Sicherheitssysteme GmbH Quick Installation Guide 2013.05 | V3 | DOC
System setup - hardware
Introduction
Scope of delivery:
– DIVAR IP 6000 – 8-bay system, fully equipped with 8 hard drives (DIP‑6082‑8HD)
– In addition to the system itself, the following items should have been shipped along with
each system
– One rackmount kit
– One AC power cable for each power supply in the system
– This quick install guide
Unpacking the system
You should inspect the box the chassis was shipped in and note if it was damaged in any way.
If the chassis itself shows damage, file a damage claim with the carrier who delivered it and
notify the respective Bosch RMA desk.
You will also need it placed near at least one grounded power outlet.
Due to the weight of the system: After opening the top of the shipping box, one person should
stand at either end and lift the disk array out together.
Be sure to read the safety precautions.
Preparing for setup
The box the system is shipped in includes a rack mount kit, which you will need to install the
system into the rack.
Follow the steps in the order given to complete the installation process in a minimum amount
of time. Read this section before you begin the installation procedure outlined in the sections
that follow.
Choosing a setup location
– Situate the system in a clean, dust-free area that is well ventilated. Avoid areas where
heat, electrical noise and electromagnetic fields are generated. Place the system near a
grounded power outlet.
– Leave approximately 25 inches clearance in front of the rack to be able to open the front
door completely.
– Leave approximately 30 inches of clearance in the back of the rack to allow for sufficient
airflow and ease in servicing.
– Install the system only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).
Notice!
This product is not suitable for use with visual display work place devices acccording to §2 of
the the German Ordinance for Work with Visual Display Units.
Rack precautions
!
Warning!
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided
to ensure your safety:
3
3.1
3.2
3.3
3.3.1
3.3.2
10 en | System setup - hardware DIVAR IP 6000 2U
2013.05 | V3 | DOC Quick Installation Guide Bosch Sicherheitssysteme GmbH
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Bosch Sicherheitssystem Handbücher
Bosch
Bosch Plena BGM Source Bedienungsanleitung
Bosch
Bosch Spexor Bedienungsanleitung
Bosch
Bosch Fire System Bedienungsanleitung
Bosch
Bosch ISW-BMC1-S135X Bedienungsanleitung
Bosch
Bosch DIP-3042-2HD Bedienungsanleitung
Bosch
Bosch DIP-2040-00N Bedienungsanleitung
Bosch
Bosch Solution 6000-IP CC615GWF Bedienungsanleitung
Bosch
Bosch Solution 16plus Bedienungsanleitung
Bosch
Bosch CM705B Anleitung zur Verwendung
Bosch
Bosch Solution 144 Bedienungsanleitung
Bosch
Bosch IUI-MAP0001 Bedienungsanleitung
Bosch
Bosch ISW-BMC1-M82X Anleitung zur Verwendung
Bosch
Bosch Plena Power Amplifier Montageanleitung
Bosch
Bosch PRAESENSA PRA-SCL Merkblatt
Bosch
Bosch TC2073 Bedienungsanleitung
Bosch
Bosch Plena PLE-1CS Referenzhandbuch
Bosch
Bosch DINION 4000 Gebrauchsanweisung
Bosch
Bosch D621 Series Bedienungsanleitung
Bosch
Bosch DIP-2040-00N Bedienungsanleitung
Bosch
Bosch LTC 1311/20 FlexiDome I Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung