Bowflex ElitePlus Bedienungsanleitung

51018 Rev AB (10/2004)

The Bowflex® Elite™

Home Gym

Assembly Instructions

CONGRATULATIONS on your commitment to improving

your health and fitness! With the Bowflex® Elite™ home gym,

you have everything you need to exceed all of your physical

fitness, strength and health expectations!

The Bowflex® Elite™ home gym’s exceptional resistance and

quality is unmatched by any other single piece of home fitness

equipment available. You will not believe the amazing results

your body will get with the Bowflex® Elite™ home gym!

With all of the fitness choices available today, finding the

best workout equipment for your needs can be confusing.

Everyone at Nautilus would like to congratulate you and thank

you for selecting the Bowflex® Elite™ home gym.

The Bowflex® Elite™ home gym is the best home fitness

product available, and you’re just about to prove it to yourself.

Get to Know Your Machine

Home Gym

Before You Assemble

Select where you are going to locate your

Bowflex® Elite™ home gym carefully. The

best place for your Bowflex® Elite™ home

gym is on a hard, level surface. Assemble

your Bowflex® Elite™ home gym in the

location where you intend to use it, as the

Bowflex® Elite™ home gym does not go

through doors easily once fully assembled.

Allow a workout area of at least 8’4” x 6’6”

(2.6m x 2.0m) of free space for safe operation

of the Bowflex® Elite™ home gym.

A-1

Get To Know Your Machine

Parts List*

Item No. Qty. Description

1 1 LOWER LAT TOWER

2 1 BASE PLATFORM

3 1 BASE RIGHT LEG

4 1 BASE LEFT LEG

5 1 SQUAT PLATFORM

6 1 CHEST BAR

7 1 SEAT PAD

8 1 SEAT BRACKET

9 1 SEAT RAIL

10 1 REAR LEG

11 1 REAR LEG CROSS TUBE

12 1 SEAT RAIL KNOB

13 1 LEG EXTENSION PIVOT TUBE

14 6 FOAM ROLLERS

15 6 FOAM ROLLER END CAPS

16 2 SHORT CHROME ROLLER TUBES

17 1 LONG CHROME ROLLER TUBE

18 2 ROLLER TUBE SPACERS

19 1 LEG EXTENSION SEAT PAD

21 1 LEG EXTENSION SEAT SUPPORT TUBE

22 1 LAT CROSS BAR

23 1 UPPER LAT TOWER

24 1 ROD BOX FRAME

25 1 ROD BOX WITH POWER RODS®

26 1 FACEPLATE

27 1 FACEPLATE BACK RIGHT

28 1 FACEPLATE BACK LEFT

29 1 BENCH PAD

30 1 LOCK OUT PIN

31 2 CHEST PULLEYS

Hardware List*

Item No. Qty. Description

A 4 SCREW, #10 PHILLIPS HEAD

B 3 SCREW, #10 X 1" PHILLIPS HEAD

C 8 SCREW, 5/16" X 3/4" BUTTON HEAD

E 10 SCREW, 3/8" X 3/4" BUTTON HEAD

F 1 SCREW, 3/8" X 2 1/2" BUTTON HEAD

G 1 SCREW, 3/8" X 2 3/4" BUTTON HEAD

H 8 SCREW, 3/8" X 3" BUTTON HEAD

I 2 SCREW, 3/8" X 3 1/4" BUTTON HEAD

J 2 SCREW, 3/8" X 4 1/4" BUTTON HEAD

K 4 SCREW, 3/8" X 5" BUTTON HEAD

L 3 WASHER, 1/4"

M 8 WASHER 5/16"

N 46 WASHER, 3/8"

O 18 NYLOCK NUT 3/8"

Q 9 BOLT COVERS, 3/8"

Accessory List*

Item No. Qty. Description

R 1 SQUAT BAR

S 1 BENT LAT BAR

T 2 HAND GRIPS

U 1 ROWING BELT

V 2 SNAP HOOKS

W 2 SQUAT STRAPS

Y 2 ROD CABLES W/ 2 SNAP HOOKS (attached)

Z 2 LAT CABLES W/ 2 SNAP HOOKS (attached)

AA 1 LEG CABLE

BB 2 SQUAT CABLES W/ 2 SNAP HOOKS (attached)

NOTE: LEAVE ALL CABLES WRAPPED AND BAGGED UNTIL YOUR BOWFLEX® ELITE™ HOME GYM IS FULLY ASSEMBLED.

*Specifications subject to change without notice.

Basic Assembly Principles

Here are a few basic tips that will make your assembly of the Bowflex® Elite™ home gym quick and easy. By using these

principles, you can simplify each process and save yourself extra time and effort.

1. To make the assembly process go faster, gather the pieces you need for each step and thoroughly read the assembly

instructions for that step prior to starting assembly for the step.

2. When tightening a locknut on a bolt, use a combination wrench to grip the locknut and ensure that it is fastened securely.

3. When attaching two pieces, gently lift and look through the bolt holes to help guide the bolt through the holes.

4. As a general rule, and for all bolts and nuts on your Bowflex® Elite™ home gym, turn bolts or nuts toward the right to

tighten and left to loosen. Or you can remember the mnemonic: “Righty tighty, lefty loosey.”

A-2

Item #: G

Qty.: 1

Descr: 3/8" X 2 3/4"

Button Head Screw

Item #: C

Qty.:

Descr: 5/16" X 3/4"

Button Head Screw

Item #: A

Qty.: 4

Descr: #10 X .75”

Phillips Head Screw

Item # N

Qty.: 46

Descr: 3/8" Flat Washer

Item #: B

Qty.: 3

Descr: #10 X 1"

Phillips Head Screw

Item #: L

Qty.: 3

Descr: 1/4" Flat Washer

Item #: H

Qty.: 8

Descr: 3/8" X 3"

Button Head Screw

Item #: E

Qty.: 10

Descr: 3/8" X 3/4"

Button Head Screw

Item #: J

Qty.: 2

Descr: 3/8" X 4 1/4"

Button Head Screw

Item #: K

Qty.: 4

Descr: 3/8" X 5"

Button Head Screw

Item #: M

Qty.: 8

Descr: 5/16" Flat Washer

Item #: O

Qty.: 18

Descr: 3/8" Nylock Nut

Tools You Will Need

You will need the following tools to complete the assembly of your Bowflex® Elite™ home gym. If you don’t have these

tools, you can find them at any hardware or department store for a reasonable price.

• 1/2" combination wrench

• 9/16" combination wrench

• Phillips screw driver

• Rubber mallet (optional)

• Utility Knife or Scissors

• (2) Allen Wrenches (included)

Hardware Guide

Item #: F

Qty.: 1

Descr: 3/8" X 2 1/2"

Button Head Screw

Item #: I

Qty.: 2

Descr: 3/8" X 3 1/4"

Button Head Screw

Note: Drawings are actual size

A-3

Step 1 - Attach the Lower Lat Tower to the Base

Platform

Locate the following items:

• Item #1 - Lower Lat Tower

• Item #2 - Base Platform

• Item #H - (4) 3/8" X 3" Button Head Screws

• Item #N - (8) 3/8" Washers

• Item #O - (4) 3/8" Nylock Nuts

Set the Base Platform (Item #2) onto the floor as shown in

Figure 1. Line up the bolt holes in the mounting channels

on the Lower Lat Tower (Item #1) with the holes in the

Base Platform tubes.

Place (4) 3/8" Washers (Item #N) over the ends of (4) 3/8" X

3" Button Head Screws (Item #H) - one washer per screw.

Insert the forward screws through the bolt holes in the Lower

Lat Tower and Base Platform first, then tip the Base Platform

back to install rear screws. Place (4) 3/8" Washers over the ends

of the screws, one washer per screw, and secure using (4) 3/8"

Nylock Nuts (Item #O), as shown in Figure 1.

Completely tighten hardware installed during Step 1.

Figure 2

Base Platform/

Lower

Lat Tower

Assembly

Stems

Tube

Ends

Stems

Pulleys

Figure 1

Mounting

Channels

Base Platform

Tubes

Forward

Screws

Step 2 - Attach the Base Legs to the Base Platform

Locate the following items:

• From Step 1 - Base Platform/Lower Lat Tower Assembly

• Item #3 - Base Right Leg - Do not unwrap cables!

• Item #4 - Base Left Leg - Do not unwrap cables!

• Item #E - (4) 3/8" X 3/4" Button Head Screws

• Item #N - (4) 3/8" Washers

With the Base Platform/Lower Lat Tower Assembly (from

Step 1) on the floor, insert the stems from each Base Leg

into the tube ends on the Base Platform, as shown in Figure 2.

Make sure to orient the 2 pulleys upward.

Carefully line up the two bolt holes on each Leg with the

corresponding holes on the Base Platform/Lower Lat Tower

Assembly.

Place (4) 3/8" Washers (Item #N) over the ends of (4) 3/8" X

3/4" Button Head Screws (Item #E) - one washer per screw.

Loosely secure the Base Legs to the Base Platform Assembly

with the screws and washers as shown in Figure 2.

Completely tighten hardware installed during Step 2.

Assembly Guide

A-4

Step 3 - Attach the Squat Platform to the Main

Assembly

Locate the following items:

• From Step 2 - Base Platform/Lat Tower (Main) Assembly

• Item #5 - Squat Platform

• Item #I - (2) 3/8" X 3 1/4" Button Head Screws

• Item #N - (4) 3/8" Washers

• Item #O - (2) 3/8" Nylock Nuts

• Item #Q - (4) Bolt Covers

With the Base Frame/Lower Lat Tower (Main)

Assembly (from Step 2) on the floor, carefully lift up the

front of the unit, then slide the Squat Platform (Rubber-

pad side down) underneath both Legs.

Line up the bolt holes in the brackets on the Squat

Platform with the bolt holes on each Leg (directly behind

the pulleys), as shown in Figure 3a.

Place (2) 3/8" Washers (Item #N) over the ends of (2)

3/8" X 3 1/4" Button Head Screws (Item #I) - one washer

per screw. Insert the screws through the lined-up holes as

shown, then place (2) 3/8" Washers and (2) 3/8" Nylock

Nuts (Item #O) over the end of each screw, securely

tightening them in place.

Completely tighten hardware installed during Step 3.

Place (2) Bolt Covers (Item #Q) over the Nylock Nuts

installed in this step - one cover per nut. Then, place (2)

additional Bolt Covers over the J-bolts, one cover per bolt,

that attach the Pulleys to the Leg, as shown in Figure 3b.

Figure 3b

Figure 3a

Base Platform/Lower

Lat Tower Assembly

Squat

Platform

Brackets

Bolt

Holes

Leg

Assembly Guide

A-5

Step 4 - Attach the Chest Bar with Pulleys to the

Main Assembly

Locate the following items:

• From Step 3 - Main Assembly

• Item #6 - Chest Bar

• Item #31 - Chest Pulleys

• Item #K - (2) 3/8" X 5" Button Head Screws

• Item #N - (4) 3/8" Washers

• Item #O - (2) 3/8" Nylock Nuts

Line up the bolt holes in the brackets on the Chest Bar

(Item #6) with the lowest bolt holes on the Lower Lat

Tower, as shown in Figure 4.

Place (2) 3/8" Washers (Item #N) over the end of (2) 3/8” X

5" Button Head Screws (Item #K) - one washer per screw.

Insert the screws through the lined up holes in the Chest

Bar and the Lower Lat Tower, and secure each screw by

placing (1) 3/8" Washers and (1) 3/8" Nylock Nuts (Item

#O) over the end of each screw.

Remove the (2) 1/4” X 1/2” Socket Head Cap Screws from

the underside of each end of the Chest Bar. Slide the Chest

Pulleys (Item #31) over each end of the Chest Bar. Install

(1) 1/4” X 1/2” Socket Head Cap Screw into the hole on

the underside of each end of the Chest Bar. This prevents

the Chest Pulleys from sliding off

Completely tighten hardware installed during Step 4.

Step 5 - Attach the Seat Bracket to the Seat Pad

Locate the following items:

• Item #7 - Seat Pad

• Item #8 - Seat Bracket

• Item #C - (4) 5/16" X 3/4" Button Head Screws

• Item #M - (4) 5/16" Washers

Place the Seat Pad (Item #7) on the floor, cushion-side down.

Position the Seat Bracket (Item #8) so the cut-out is toward the

angled edge of the Seat Pad. Align the four holes in the Seat

Bracket with the four holes in the Seat Pad.

Place (4) 5/16" Washers (Item #M) over (4) 5/16" X 3/4" Button

Head Screws (Item #C) - one over each screw, and use those

screws to secure the Seat Bracket to the Seat Pad.

Completely tighten hardware installed during Step 5.

Figure 5

Cut-out

Angled

Edge

Base Platform/

Lower Lat Tower

Assembly

Figure 4

Chest Bar

Brackets

Assembly Guide

A-6

Step 6 - Attach the Seat Rail to the Seat Assembly

Locate the following items:

• From Step 5 - Seat Pad/Seat Bracket Assembly

• Item #9 - Seat Rail

Undo the twist ties from the Rail Pivot Bushings and remove the

Bushings. Set aside until the end of this step.

Line up the Seat Rail (Item #9) with the Seat Assembly (from Step

5). Orient the Seat Rail so that the Pull Pin on the Seat Bracket is

on the same side as the holes in the Seat Rail.

Pull out the Pull Pin on the Seat Bracket, and then insert the

Seat Rail through the Seat Bracket, (see Figure 6).

To adjust the Seat, slide the Seat until the Pull Pin is aligned

with one hole, then release the Pull Pin into the hole.

Once you have attached the Seat Assembly to the Seat Rail,

reinstall the Rail Pivot Bushings that you removed at the

beginning of this step.

Note: See Step 22 to adjust the Seat Bracket.

Step 7 - Attach the Rear Leg to the Rear Leg Cross

Tube

Locate the following items:

• Item #10 - Rear Leg - Do not unwrap cables!

• Item #11 - Rear Leg Cross Tube

• Item #H - (2) 3/8" X 3" Button Head Screws

• Item #N - (4) 3/8" Washers

• Item #O - (2) 3/8" Nylock Nuts

Line up the holes in the bracket on the Rear Leg (Item #10) with

the holes in the Rear Leg Cross Tube (Item #11) as shown in

Figure 7.

Place (2) 3/8" Washers (Item #N) over the end of (2) 3/8"

X 3" Button Head Screws (Item #H) - one per each screw.

Insert the screws through the lined up holes, and secure by

placing (1) 3/8" Washer and (1) 3/8" Nylock Nut (Item #O)

over the end of each screw, as shown in Figure 7.

Completely tighten hardware installed during Step 7.

Figure 7

Rear Leg

Bracket

Figure 6

Seat Pad/Seat

Bracket Assembly

Holes in the

Seat Rail

Pull Pin

Rail Pivot

Bushings

Assembly Guide

A-7

Step 8 - Attach the Rear Leg to the Seat Rail

Locate the following items:

• From Step 6 - Seat Rail Assembly

• From Step 7 - Rear Leg Assembly

• Item #J - (1) 3/8" X 4 1/4" Button Head Screw

• Item #N - (2) 3/8" Washers

• Item #O - (1) 3/8" Nylock Nut

• Item #Q - (2) Bolt Covers

Undo the twist ties from the Pivot Bushings on the end of the Rear

Leg Assembly (from Step 6), but do not remove the Bushings.

Note: When attaching the Rear Leg Assembly (from Step 7)

to the Seat Rail Assembly, rotate the Rear Leg forward (as

shown in Figure 8b), to allow the Leg Latch to engage with

the Seat Rail Pull Pin.

Align the holes on the End Bracket of the Seat Rail Assembly

with the middle holes on the Rear Leg Assembly, (see Figure 8).

Place (1) 3/8" Washer (Item #N) over the end of (1) 3/8" X 4 1/4"

Button Head Screw (Item #J). Insert the screw through the lined

up holes and then loosely secure on the opposite side by placing (1)

3/8" Washer and (1) 3/8" Nylock Nut (Item #O) over the end.

Do not over-tighten hardware from Step 8.

Note: Tighten the nylock nut enough that the threads of the

screw extend through the nylock nut, but loosely enough that the

Leg Assembly can move freely.

At this time, place (1) Bolt Cover (Item #Q) over the

Nylock Nut installed during Step 8, place 1 bolt cover over

the Nylock Nut going through the rear leg pulley.

Once you have completed Step 8, rotate the Rear Leg back

until it engages the Seat Rail Pull Pin.

Figure 8

Rear Leg

Assembly

Rail

Assembly

End

Bracket

Middle

Hole

Figure 8b

Rail

Assembly

Rear Leg

Seat Rail

Pull Pin

Leg Latch

Assembly Guide

A-8

Step 9 - Attach the Seat Rail to the Main Assembly

Locate the following items:

• From Step 4 - Main Assembly

• From Step 8 - Seat Rail Assembly

• Item #12 - Seat Rail Knob

• Item #J - (1) 3/8" X 4 1/4" Button Head Screw

• Item #N - (2) 3/8" Washers

• Item #O - (1) 3/8" Nylock Nut

• Item #Q - (1) Bolt Cover

Align the holes on the Seat Rail Assembly (from Step 8)

with the holes in the Rail Bracket on the Main Assembly

(from Step 4), as shown in Figure 9.

Insert the Seat Rail Assembly into the Seat Rail Bracket,

and then place (1) 3/8" Washer (Item #N) over the end of

(1) 3/8" X 4 1/4" Button Head Screw (Item #J). Insert the

screw through the aligned holes, as shown, and place (1)

3/8" Washer and (1) 3/8" Nylock Nut (Item #O) over the

end of the screw to secure.

Do not over-tighten the hardware from Step 9.

Note: Tighten the nylock nut enough that the threads of the

screw extend through the nylock nut, but loosely enough that

the Seat Rail Assembly can move freely.

At this time, place (1) Bolt Cover (Item #Q) over the

Nylock Nut installed during Step 9. Then, thread the Seat

Rail Knob (Item #12) into the top hole on the Seat Rail

Bracket, as shown in Figure 9, but do not over-tighten.

Figure 9

Rail

Assembly

Main

Assembly

Seat Rail

Bracket

Assembly Guide

Andere Handbücher für ElitePlus

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bowflex Heim-Fitnessstudio Handbücher

Bowflex

Bowflex SelectTech 4.1 Bedienungsanleitung

Bowflex

Bowflex Xceed Bedienungsanleitung

Bowflex

Bowflex BOWFLEX XTREME.SE Bedienungsanleitung

Bowflex

Bowflex SelectTech 5.1 Bedienungsanleitung

Bowflex

Bowflex ULTIMATE 2 Bedienungsanleitung

Bowflex

Bowflex SelectTech 2080 Bedienungsanleitung

Bowflex

Bowflex Xtreme 2 Bedienungsanleitung

Bowflex

Bowflex PR3000 Bedienungsanleitung

Bowflex

Bowflex Xceed Plus Bedienungsanleitung

Bowflex

Bowflex Xtreme SE Bedienungsanleitung

Bowflex

Bowflex Xtreme SE Bedienungsanleitung

Bowflex

Bowflex Bowflex Xtreme 2 SE Bedienungsanleitung

Bowflex

Bowflex Xtreme 2 Bedienungsanleitung

Bowflex

Bowflex BOWFLEX XTREME.SE Bedienungsanleitung

Bowflex

Bowflex PR1000 Bedienungsanleitung

Bowflex

Bowflex ElitePlus Bedienungsanleitung

Bowflex

Bowflex Classic Bedienungsanleitung

Bowflex

Bowflex Blaze Bedienungsanleitung

Bowflex

Bowflex Blaze Bedienungsanleitung

Bowflex

Bowflex Conquest Bedienungsanleitung

Bowflex

Bowflex Conquest Bedienungsanleitung

Bowflex

Bowflex Revolution Bedienungsanleitung

Bowflex

Bowflex Bowflex Xtreme 2 SE Bedienungsanleitung

Bowflex

Bowflex Revolution Bedienungsanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Weider

Weider 8300 Hard Drive Bedienungsanleitung

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Weider

Weider 8700 I Kurzanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Weider

Weider WEMC10161 Bedienungsanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

ParaBody

ParaBody 40 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Insportline

Insportline RW600 Bedienungsanleitung

Stamina

Stamina 55-1532 Bedienungsanleitung