Bradford White RE350T6-1NC Series Bedienungsanleitung

238-44422-00P REV 9/14

ELECTRIC WATER HEATER

THE WARRANTY ON THIS WATER HEATER IS IN EFFECT ONLY WHEN

THE WATER HEATER IS INSTALLED AND OPERATED IN

ACCORDANCE WITH LOCAL CODES AND THESE INSTRUCTIONS.

THE MANUFACTURER OF THIS HEATER WILL NOT BE LIABLE FOR

ANY DAMAGE RESULTING FROM FAILURE TO COMPLY WITH THESE

INSTRUCTIONS. READ THESE INSTRUCTIONS THOROUGHLY

BEFORE STARTING.

For your family’s comfort, safety and convenience, it is

recommended this water heater be installed and serviced by a

plumbing professional.

A Spanish language version of these instructions is available by contacting

the manufacturer listed on the rating plate.

La version espanola de estas instruccions se puede obtener al escribirle a la

fábrica cuyo nombre aparece in la placa de especificaciones.

INSTALLATION & OPERATING

INSTRUCTION MANUAL

TABLE OF CONTENTS

General Information ........................................................ 3

Installation ....................................................................... 4

Locating The Water Heater ......................................... 4

Water Connections...................................................... 6

Electrical Connections................................................13

General Operation ...........................................................14

Thermostat Adjustment ..............................................15

Maintenance.....................................................................16

Notes ................................................................................19

CONGRATULATIONS!

You have just purchased one of the finest water heaters on

the market today!

This installation, operation and instruction manual will

explain in detail the installation and maintenance of your

new Electric Water Heater. We strongly recommend that

you contact a plumbing professional for the installation of

this water heater.

We require that you carefully read this manual, as well as

the enclosed warranty, and refer to it when questions arise.

If you have any specific questions concerning your

warranty, please consult the plumbing professional from

whom your water heater was purchased. For your records

we recommend that you write the model, serial number and

installation date of your water heater in the maintenance

section in the back of this manual.

This manual should be kept with the water heater.

GENERAL INFORMATION

This electric water heater’s design is certified by INTERTEK (ETL) and listed

in accordance with UL 174. CETL listed in accordance with Canadian

National Standard C22.2, No. 110-M90.

Water heaters with a capacity of 19 gallons through 119 gallons are

evaluated by INTERTEK in accordance with Part 280.707(d) (1) of HUD

Mobile Home Construction and Safety Standards for Energy Efficiency. For

mobile home installations, these water heaters must be installed in

accordance with Section 3280.709 of HUD Mobile Home Construction and

Safety Standards for Installation of Appliances.

This water heater must be installed in accordance with local codes. In the

absence of local codes, install this water heater in accordance with the

N.E.C. Reference Book (latest edition).

The warranty for this water heater is in effect only when the water heater is

installed, adjusted, and operated in accordance with these Installation and

Operating Instructions. The manufacturer will not be held liable for damage

resulting from alteration and/or failure to comply with these instructions.

This water heater has been designed and certified for the purpose of heating

potable water. The installation and use of this water heater for any purpose

other than the heating of potable water, may cause damage to the water

heater and create a hazardous condition and nullify the warranty.

Do not use this appliance if any part has been submerged in water. The

plumbing professional responsible for the installation of this water heater

should be contacted to inspect the appliance and to replace any part of the

control system, including thermostat, which has been submerged in water.

Make sure that the rating plate on the water heater is referenced for certainty

that the correct voltage is being supplied to the water heater.

CAUTION

Incorrect operation of this appliance may create a hazard to life and

property and will nullify the warranty.

DANGER

Do not store or use gasoline or other flammable, combustible, or

corrosive vapors and liquids in the vicinity of this or any other

appliance.

General Information continued-

A sacrificial anode is used to extend tank life. Removal of this anode, for any

reason, will nullify the warranty. In areas where water is unusually active, an

odor may occur at the hot water faucet due to a reaction between the

sacrificial anode and impurities in the water. If this should happen, an

alternative anode may be purchased from the supplier that installed this

water heater. This will minimize the odor while protecting the tank.

Additionally, the water heater should be flushed with appropriate dissolvers

to eliminate any bacteria.

INSTALLATION

Locating The Water Heater

This water heater MUST be installed indoors out of the wind and

weather.

This water heater shall NOT be installed in any location where gasoline

or flammable vapors are likely to be present, unless the installation is

such to eliminate the probable ignition of gasoline or flammable

vapors.

The location this water heater is to be installed is of utmost importance.

Before installing this water heater, consult the installation section of these

instructions. After reading these installation and operating instructions,

select a location for the water heater where the floor is level and is easily

accessible to a power supply and water connections. It is recommended

that the water heater be located near the center of greatest hot water usage

to prevent heat loss through the pipes.

DO NOT locate the water heater where water lines could be subjected

to freezing temperatures. Locate the water heater so that access

panels and drain valves are accessible.

IMPORTANT

Before proceeding, please inspect the water heater and it’s components for

possible damage. DO NOT install any damaged components. If damage is

evident, please contact the supplier where the water heater was purchased

or the manufacturer listed on the rating plate for replacement parts.

WARNING

Water heaters are heat producing appliances. To avoid damage or injury,

there shall be no materials stored against the water heater and proper care

shall be taken to avoid unnecessary contact (especially by children) with

the water heater. UNDER NO CIRCUMSTANCES SHALL FLAMMABLE

MATERIALS, SUCH AS GASOLINE OR PAINT THINNER BE USED OR

STORED IN THE VICINITY OF THIS WATER HEATER OR ANY

LOCATION FROM WHICH FUMES COULD REACH THE WATER

HEATER.

Locating The Water Heater continued-

Some models are not equipped with a drain valve. For those models, install

a drain tee in the cold water inlet as close as practical to the water heater.

Water heater corrosion and component failure can be caused by the heating

and breakdown of airborne chemical vapors. Examples of some typical

compounds that are potentially corrosive are: spray can propellants, cleaning

solvents, refrigerator and air conditioning refrigerants, swimming pool

chemicals, calcium or sodium chloride, waxes and process chemicals.

These materials are corrosive at very low concentration levels with little or no

odor to reveal their presence.

NOTE: DAMAGE TO THE WATER HEATER CAUSED BY EXPOSURE TO

CORROSIVE VAPORS IS NOT COVERED BY THE WARRANTY. DO

NOT OPERATE THE WATER HEATER IF EXPOSURE HAS OR WILL

OCCUR. DO NOT STORE ANY POTENTIALLY CORROSIVE

COMPOUNDS IN THE VICINITY OF THE WATER HEATER.

This water heater must be located in an area where leakage of the tank or

water line connections and the combination temperature and pressure relief

valve will not result in damage to the area adjacent to the water heater or to

lower floors of the structure. When such locations cannot be avoided, a

suitable drain pan must be installed under the water heater. The drain pan

must have a minimum length and width of at least 4 in. (10.2 cm) greater

than the diameter of the water heater. The drain pan, as described above,

can be purchased from your plumbing professional. The drain pan must be

piped to an adequate drain. The piping must be pitched for proper drainage.

CLEARANCES

1. Minimum clearance to combustible material is 0 inches for the Top,

Sides, Front, and Rear of this water heater. However, it is recommended

that at least 18 inches (45.7 cm) from the Top, and 24 inches (61 cm)

from the Front. Clearance for servicing may be reduced down to

minimum clearance to combustible material, but service time and effort

may be greatly increased.

2. Increase distances to provide clearances for servicing.

To comply with NSF requirements this water heater is to be:

a) Sealed to the floor with sealant, in a smooth and easily cleanable

way, or

b) Installed with an optional leg kit that includes legs and/or extensions

that provide a minimum clearance of 6” beneath the water heater.

Note: For California installation this water heater must be braced,

anchored, or strapped to avoid falling or moving during an earthquake.

See instructions for correct installation procedures. Instructions may

be obtained from DSA Headquarters Office, 1102 Q Street, Suite 5100,

Sacramento, CA 95811.

Water Connections

NOTE: BEFORE PROCEEDING WITH THE INSTALLATION, CLOSE THE

MAIN WATER SUPPLY VALVE.

After shutting the main water supply valve, open a faucet to relieve the water

line pressure to prevent any water from leaking out of the pipes while making

the water connections to the water heater. After the pressure has been

relieved, close the faucet. The COLD water inlet and HOT water outlet are

identified on top of the water heater. The fittings at the cold water inlet and

hot water outlet are dielectric waterway fittings with 3/4” NPT tapered male

threads. Make the proper plumbing connections between the water heater

and the plumbing system in the house. Install a shut-off valve in the cold

water supply line.

If this water heater is installed in a closed water supply system, such as the

one having a back-flow preventer in the cold water supply, provisions shall

be made to control thermal expansion. DO NOT operate this water heater in

a closed system without provisions for controlling thermal expansion. Your

water supplier or local plumbing inspector should be contacted on how to

control this situation.

After installation of the water lines, open the main water supply valve and fill

the water heater. While the water heater is filling, open several hot water

faucets to allow air to escape from the water system. When a steady stream

of water flows through the faucets, close them and check all water

connections for possible leaks. NEVER OPERATE THE WATER HEATER

WITHOUT FIRST BEING CERTAIN IT IS FILLED WITH WATER.

CAUTION

If sweat fittings are to be used, DO NOT apply heat to the nipples on top

of the water heater. Sweat the tubing to the adapter before fitting the

adapter to the water connections. It is imperative that heat is not applied

to the nipples containing a plastic liner.

IMPORTANT

FAILURE TO INSTALL AND MAINTAIN A NEW, LISTED 3/4” X 3/4”

TEMPERATURE-PRESSURE RELIEF VALVE WILL RELEASE THE

MANUFACTURER FROM ANY CLAIM WHICH MIGHT RESULT FROM

EXCESSIVE TEMPERATURE AND PRESSURES.

Water Connections continued-

WARNING

For protection against excessive temperatures and pressure, install

temperature and pressure protective equipment required by local codes,

but not less than a combination temperature and pressure relief valve

certified by a nationally recognized testing laboratory that maintains

periodic inspection of production of listed equipment or materials, as

meeting the Requirements for Relief Valves and Automatic Gas Shutoff

Devices for Hot Water Supply Systems, ANSI Z21.22, and the Standard

CAN1-4.4 Temperature, Pressure, Temperature and Pressure Relief

Valves and Vacuum Relief Valves. The combination temperature and

pressure relief valve shall be marked with a maximum set pressure, not to

exceed the maximum working pressure of the water heater. The

combination temperature and pressure relief valve shall also have an

hourly rated temperature steam BTU discharge capacity not less than the

hourly input rating of the water heater.

Install the combination temperature and pressure relief valve into the

opening provided and marked for this purpose on the water heater

Note: Some models may already be equipped or supplied with a

combination temperature and pressure relief valve. Verify that the

combination temperature and pressure relief valve complies with local

codes. If the combination temperature and pressure relief valve does not

comply with local codes, replace it with one that does. Follow the

installation instructions above on this page.

Install a discharge line so that water discharged from the combination

temperature and pressure relief valve will exit within six (6) inches (15.3

cm) above, or any distance below the structural floor and cannot contact

any live electrical part. The discharge line is to be installed to allow for

complete drainage of both the temperature and pressure relief valve and

the discharge line. The discharge opening must not be subjected to

blockage or freezing. DO NOT thread, plug or cap the discharge line. It is

recommended that a minimum of four (4) inches (10.2 cm) be provided on

the side of the water heater for servicing and maintenance of the

combination temperature and pressure relief valve.

Do not place a valve between the combination temperature and pressure

relief valve and the tank.

Water Connections continued-

WARNING

Hydrogen gas can be produced in a hot water system served by this

water heater that has not been used for a long period of time

(generally two weeks or more). Hydrogen gas is extremely

flammable. To reduce the risk of injury under these conditions, it is

recommended that the hot water faucet be opened for several

minutes at the kitchen sink before using any electrical appliance

connected to the hot water system. If hydrogen is present, there will

probably be an unusual sound such as air escaping through the pipe

as the water begins to flow. There should be no smoking or open

flame near the faucet at the time it is open.

CAUTION

INCREASING THE THERMOSTAT SETTING ABOVE THE PRESET

TEMPERATURE MAY CAUSE SEVERE BURNS AND CONSUME

EXCESSIVE ENERGY. HOTTER WATER INCREASES THE RISK OF

SCALD INJURY.

Water Connections continued-

This water heater can deliver scalding temperature water at any faucet in the

system. Be careful whenever using hot water to avoid scalding injury.

Certain appliances, such as dishwashers and automatic clothes washers,

may require increased temperature water. By setting the thermostat on this

water heater to obtain increased temperature water required by these

appliances, you may create the potential for scald injury. To protect against

injury, you should install an ASSE approved mixing valve in the water

system. This valve will reduce point of discharge temperature by mixing cold

and hot water in branch supply lines. Such valves are available from the

manufacturer of this water heater or a local plumbing supplier. Please

consult with a plumbing professional.

APPROXIMATE TIME/TEMPERATURE RELATIONSHIPS IN SCALDS

120°F (49°C) More than 5 minutes

125°F (52°C) 1½ to 2 minutes

130°F (54°C) About 30 seconds

135°F (57°C) About 10 seconds

140°F (60°C) Less than 5 seconds

145°F (63°C) Less than 3 seconds

150°F (66°C) About 1½ seconds

155°F (68°C) About 1 second

(52°C) can cause severe burns

are at highest risk of being

Children, disabled and elderly

instantly or death from scalds.

Water temperature over 125°F

Feel water before bathing or

before setting temperature

available.

showering.

Temperature limiting valves are

Review this instruction manual

at water heater.

scalded.

Water Connections continued-

Upright Models (See Figures 1A & 1B)

The hot and cold water connections are identified on the top of the water

heater (See figure 1A). For bottom inlet models (-503 models), the cold

water inlet is located on the side of the drain valve (see figure 1B). Connect

the hot and cold water lines to the installed nipples using unions. Install a

listed temperature-pressure relief valve in the opening on the side of the

water heater.

Figure 1A (Top Inlet Models)

Figure 1B (Bottom Inlet Models)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradford White Boiler Handbücher

Bradford White

Bradford White Brute MagnaTech BCFH1000 Bedienungsanleitung

Bradford White

Bradford White Brute MagnaTech BMGV1600 Bedienungsanleitung

Bradford White

Bradford White 238-44219-00J Beilage

Bradford White

Bradford White 238-46392-00G Montageanleitung

Bradford White

Bradford White MII Series Bedienungsanleitung

Bradford White

Bradford White 30S Bedienungsanleitung

Bradford White

Bradford White RE2 Bedienungsanleitung

Bradford White

Bradford White mi5036en10 Bedienungsanleitung

Bradford White

Bradford White UCG100H3993N Bedienungsanleitung

Bradford White

Bradford White RG250H6N-475 Bedienungsanleitung

Bradford White

Bradford White BWCV Bedienungsanleitung

Bradford White

Bradford White Gas Water Heaters Bedienungsanleitung

Bradford White

Bradford White U4-30T6FRN Bedienungsanleitung

Bradford White

Bradford White 238-37281-00R Beilage

Bradford White

Bradford White ECO-DEFENDER U130T*FRN Bedienungsanleitung

Bradford White

Bradford White TTW URG2PV75H6N Bedienungsanleitung

Bradford White

Bradford White RE340T6 Betriebsanleitung

Bradford White

Bradford White ULG2100H805N Bedienungsanleitung

Bradford White

Bradford White VR-150-(kW) Handbuch

Bradford White

Bradford White PE4403S Series Bedienungsanleitung

Bradford White

Bradford White 238-45917-OON Beilage

Bradford White

Bradford White RG130T*N Series Bedienungsanleitung

Bradford White

Bradford White UPDX series Bedienungsanleitung

Bradford White

Bradford White RG250T6N Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung